Magnavox TB110MW9 Connections, A Connecting to a TV without A/V Jacks, white red yellow

Page 10

Connections

Connections

1Disconnect the AC power cords of the devices from the AC outlet.

Desconecte los cables de alimentación de los aparatos del tomacorriente CA.

2Disconnect RF coaxial cable from antenna input jack of your TV.

Desconecte el cable coaxial de RF del conector hembra de entrada de antena de su televisor.

3Make the connections as illustrated below.

Efectúe las conexiones tal como se ilustra a continuación.

4Plug all AC power cords into AC outlets, then turn all devices on.

Enchufe todos los cables eléctricos de CA en los tomacorrientes de CA y conecte la alimentación de todos los equipos.

AConnecting to a TV without A/V Jacks

Conexión a un TV sin tomas de A/V

TV

TV antenna

Antena de TV

STB

RF cable (supplied)

cable de RF (se incluye)

BConnecting to a TV with A/V Jacks

Conexión a un TV con tomas de A/V

TV

TV antenna

Antena de TV

STB

white red

yellow

NOTE:

	yellow
white
red

Audio cable
cable de audio		Video cable
		Video cable
		cable de
		video

•If your TV has only one audio jack, connect the AUDIO OUT jack (L) (white) on the STB to the audio input jack on the TV.

Si su TV sólo tiene una toma de audio, conecte la toma AUDIO OUT (L) (blanco) del STB, a la toma de entrada de audio del TV.

10

EN

Image 10

Contents TB110MW9 INSTRUCCIONES EN ESPAÑOL INCLUIDASTHAT MAKE USING YOUR MAGNAVOX PRODUCT MORE ENJOYABLE DTV Digital to Analog Converter Set Top BoxImportant Safeguards Before UsingRISK OF ELECTRIC SHOCK DO NOT OPEN Dealer Phone No Before UsingINSERT Model NoLocation PrecautionsInstall the product in a horizontal position Avoid the Hazards of Electrical Shock and FireT a b l e o f C o n t e n t s Before UsingInitial Setup Setup Wizard Advanced OperationConexión a un TV con tomas de A/V OverviewConexión a un TV sin tomas de A/V Conexión a una caja de cableCheck the following accessories when unpacking the STB AccessoriesInstalling Batteries 1 Unsnap the battery cover from theUbicación del control Remote ControlLocation of Controls 2 Number buttons 3 OK buttonFront Panel 1 Remote control sensor 2 POWER indicator1 AC power cord Rear PanelConnections A Connecting to a TV without A/V JacksB Connecting to a TV with A/V Jacks white red yellowwhite C Connecting to a Cable Box OptionalNote to the Cable TV System Installer y ellowred yellow D Connecting to Other DevicesConexión a otros dispositivos on the STB to the audio input jack on the DVD1 Press STANDBY-ON on the remote control to activate the STB Initial Setup Setup WizardInitial Setup ”SETUP WIZARD” screen automatically appears6 Select your time zone using K / L, then press OK 3 Select “CONTINUE” using s / B, then press OK4 Select the language using K / L, then press OK 9 Select “AUTOSCAN” using K / L, then press OKIf the sub-channel number is 1 digit, press OK when finish entering using CH K / LIf the main channel number is 1 digit, press . when finish entering “NO SIGNAL” appears after the sub-channel broadcast is overPress STILL To cancel still modePress AUDIO repeatedly Choosing Audio LanguagePress DISPLAY 2 Select the desired program using s / Bprovide signals for “EPG” 1 Press EPG while watching TV4 Select “AUTOSCAN” using K / L, then press OK 1 Press SETUP 2 Select “CHANNEL” using K / L, then press OK3 Select “AUTOSCAN” using K / L, then press OK 1 Press SETUP5 Press OK again to add the channel to the channel map 6 Press SETUP to exit4 Select “DELETE” using K / L, then press OK Operation4 Select “ANTENNA” using K / L, then press OK Adjusting Antenna2 Press SETUP 3 Select “CHANNEL” using K / L, then press OK 1 Press SETUP 2 Select “DETAIL” using K / L, then press OK3 Select “TIME ZONE” using K / L , then press OK Setting the Time Zone and D.S.T Daylight Saving Time1 Press SETUP 2 Select “TIME” using K / L , then press OK 4 Select your time zone using K / L , then press OK1 Press SETUP 2 Select “DETAIL” using K / L , then press OK 3 Select “D.S.T” using K / L , then press OK4 Select “ON” or “OFF” using s / B , then press OK 3 Select “V-CHIP” using K / L , then press OKK / L , then press OK repeatedly to switch between view and block 5 Select the desired rating type using K / L , then press OK6 Select the desired rating using MPAA Rating5 Select “NEW PASSWORD” using K / L , then press OK 7 Press SETUP to exit4 Enter 4737 in the password entry field 6 Enter the new 4-digit password using the Number buttons4 Select the desired closed caption item using K / L , then press OK 5 Select “MANUAL” using K / L , then press OK3 Select “CLOSED CAPTION” using K / L , then press OK 5 Select the desired DTV closed caption using K / L , then press OK3 Select “AUTO POWER DOWN” using K / L , then press OK Auto Power Down4 Select desired amount of time using K / L , then press OK You cannot view Analog TV with this setting You can view analog TV by switching “RF OUT” settingYou cannot view Digital TV with this setting Viewing Analog TV2 Select “RF THROUGH” in “RF OUT” You can view analog TV without switching “RF OUT” settingMethod 2 Método 3 Select the desired channel on your TV2 Select “CHANNEL” using K / L, then press OK Setting RF OUTUsing SETUP to Switch “RF OUT” Setting 3 Select “RF OUT” using K / L, then press OKto the remote control TroubleshootingNo power Low volumePower Source SpecificationsConnecting Jacks ANT. IN/OUT Power ConsumptionFUNAI SERVICE CORPORATION LIMITED WARRANTYWARRANTY STATEMENT REGARDING NON AUTHORIZED REPAIRS Customer Service