Magnavox TB110MW9 Adjusting Antenna, Selecting Display Mode, Press SETUP to exit, Status bar

Page 20

Adjusting Antenna

Advanced Operation

Adjusting Antenna

You can verify the signal strength of each channel.

1Select a channel to adjust using [the Number buttons] or [CH K / L ].

2 Press [SETUP].

3Select “CHANNEL” using [ K / L], then press [OK].

4Select “ANTENNA” using [ K / L], then press [OK].

CHANNEL

EXIT		ADD/DELETE
CHANNEL
		ANTENNA
TIME		ADD/DELETE

DETAIL		RF OUT

INITIAL

•STB starts receiving the signal for the channel.

5By referring to the on-screen indication, adjust the antenna’s direction to get the best reception.

Status bar:

Stretches to the right as the signal strength gets stronger.

ANTENNA		10.1
		10.1
EXIT	WEAK	STRONG
	WEAK	STRONG
CHANNEL	NOW
TIME	10
TIME		50
		50
DETAIL	BACK	PEAK
DETAIL

INITIAL

Peak indicator:

Indicates the highest strength ever reached.

To adjust other channels:

Select the channel using [CH K / L ], then adjust it.

6 Press [SETUP] to exit.

Selecting Display Mode

You can adjust the aspect ratio of the digital TV program to fit your 4:3 TV monitor.

Display Mode

1 Press [SETUP].

2Select “DETAIL” using [ K / L], then press [OK].

SETUP

EXIT
EXIT		V-CHIP
CHANNEL		V-CHIP
CHANNEL		CLOSED CAPTION
		CLOSED CAPTION
TIME		DISPLAY MODE	LETTERBOX
DETAIL		AUTO POWER DOWN		4 HOURS
INITIAL

3Select“DISPLAY MODE”using [ K / L], then press [OK].

DETAIL

	EXIT		V-CHIP
	CHANNEL		V-CHIP
	CHANNEL		CLOSED CAPTION
			CLOSED CAPTION
	TIME
			DISPLAY MODE		LETTERBOX
	DETAIL		AUTO POWER DOWN
	DETAIL		AUTO POWER DOWN			4 HOURS
	INITIAL

4Select the desired display mode using [ K / L], then press [OK].

* Descriptions of each settings are explained in the “Information on Display Mode” on the next page.

Select display mode.

LETTERBOX

ZOOM

FULL

5 Press [SETUP] to exit.

20

EN

Image 20

Contents INSTRUCCIONES EN ESPAÑOL INCLUIDAS THAT MAKE USING YOUR MAGNAVOX PRODUCT MORE ENJOYABLETB110MW9 DTV Digital to Analog Converter Set Top BoxRISK OF ELECTRIC SHOCK DO NOT OPEN Before UsingImportant Safeguards Before Using INSERTDealer Phone No Model NoPrecautions Install the product in a horizontal positionLocation Avoid the Hazards of Electrical Shock and FireBefore Using Initial Setup Setup WizardT a b l e o f C o n t e n t s Advanced OperationOverview Conexión a un TV sin tomas de A/VConexión a un TV con tomas de A/V Conexión a una caja de cableAccessories Installing BatteriesCheck the following accessories when unpacking the STB 1 Unsnap the battery cover from theRemote Control Location of ControlsUbicación del control 2 Number buttons 3 OK button1 Remote control sensor 2 POWER indicator 1 AC power cordFront Panel Rear PanelA Connecting to a TV without A/V Jacks B Connecting to a TV with A/V JacksConnections white red yellowC Connecting to a Cable Box Optional Note to the Cable TV System Installerwhite y ellowD Connecting to Other Devices Conexión a otros dispositivosred yellow on the STB to the audio input jack on the DVDInitial Setup Setup Wizard Initial Setup1 Press STANDBY-ON on the remote control to activate the STB ”SETUP WIZARD” screen automatically appears3 Select “CONTINUE” using s / B, then press OK 4 Select the language using K / L, then press OK6 Select your time zone using K / L, then press OK 9 Select “AUTOSCAN” using K / L, then press OKusing CH K / L If the main channel number is 1 digit, press . when finish enteringIf the sub-channel number is 1 digit, press OK when finish entering “NO SIGNAL” appears after the sub-channel broadcast is overTo cancel still mode Press AUDIO repeatedlyPress STILL Choosing Audio Language2 Select the desired program using s / B provide signals for “EPG”Press DISPLAY 1 Press EPG while watching TV1 Press SETUP 2 Select “CHANNEL” using K / L, then press OK 3 Select “AUTOSCAN” using K / L, then press OK4 Select “AUTOSCAN” using K / L, then press OK 1 Press SETUP6 Press SETUP to exit 4 Select “DELETE” using K / L, then press OK5 Press OK again to add the channel to the channel map OperationAdjusting Antenna 2 Press SETUP 3 Select “CHANNEL” using K / L, then press OK4 Select “ANTENNA” using K / L, then press OK 1 Press SETUP 2 Select “DETAIL” using K / L, then press OKSetting the Time Zone and D.S.T Daylight Saving Time 1 Press SETUP 2 Select “TIME” using K / L , then press OK3 Select “TIME ZONE” using K / L , then press OK 4 Select your time zone using K / L , then press OK3 Select “D.S.T” using K / L , then press OK 4 Select “ON” or “OFF” using s / B , then press OK1 Press SETUP 2 Select “DETAIL” using K / L , then press OK 3 Select “V-CHIP” using K / L , then press OK5 Select the desired rating type using K / L , then press OK 6 Select the desired rating usingK / L , then press OK repeatedly to switch between view and block MPAA Rating7 Press SETUP to exit 4 Enter 4737 in the password entry field5 Select “NEW PASSWORD” using K / L , then press OK 6 Enter the new 4-digit password using the Number buttons5 Select “MANUAL” using K / L , then press OK 3 Select “CLOSED CAPTION” using K / L , then press OK4 Select the desired closed caption item using K / L , then press OK 5 Select the desired DTV closed caption using K / L , then press OK4 Select desired amount of time using K / L , then press OK Auto Power Down3 Select “AUTO POWER DOWN” using K / L , then press OK You can view analog TV by switching “RF OUT” setting You cannot view Digital TV with this settingYou cannot view Analog TV with this setting Viewing Analog TVYou can view analog TV without switching “RF OUT” setting Method 2 Método2 Select “RF THROUGH” in “RF OUT” 3 Select the desired channel on your TVSetting RF OUT Using SETUP to Switch “RF OUT” Setting2 Select “CHANNEL” using K / L, then press OK 3 Select “RF OUT” using K / L, then press OKTroubleshooting No powerto the remote control Low volumeSpecifications Connecting Jacks ANT. IN/OUTPower Source Power ConsumptionLIMITED WARRANTY WARRANTY STATEMENT REGARDING NON AUTHORIZED REPAIRSFUNAI SERVICE CORPORATION Customer Service