Magnavox TB110MW9 Specifications, Others, Product, Tuner, Connecting Jacks ANT. IN/OUT, Weight

Page 31

Specifications

Product

DTV Digital to Analog Converter

Tuner

Receivable channels 2-69ch

Connecting Jacks

ANT. IN/OUT

RF connector x2 (75ohm)

Video Output

RCA jack x1, 1Vpp (75ohm)

Analog Audio Output

RCA jack (L / R) x2 2V rms (100k ohm)

Power Source

120V AC+/-10%, 60Hz+/-0.5%

Power Consumption

8W (Power on), Less than 1 W (Power off )

Closed Caption System

§15.122/FCC (digital CC)

Operating Condition

41°F (5°C) - 104°F (40°C)

Dimensions (W x H x D)

9.5" x 1.7" x 6"

(240mm x 43mm x 150mm)

Weight

1.4lbs. (0.6Kg)

Designs and Specifications are subject to change without notice.

Finin

Others

Image 31

Contents DTV Digital to Analog Converter Set Top Box INSTRUCCIONES EN ESPAÑOL INCLUIDASTHAT MAKE USING YOUR MAGNAVOX PRODUCT MORE ENJOYABLE TB110MW9Important Safeguards Before UsingRISK OF ELECTRIC SHOCK DO NOT OPEN Model No Before UsingINSERT Dealer Phone NoAvoid the Hazards of Electrical Shock and Fire PrecautionsInstall the product in a horizontal position LocationAdvanced Operation Before UsingInitial Setup Setup Wizard T a b l e o f C o n t e n t sConexión a una caja de cable OverviewConexión a un TV sin tomas de A/V Conexión a un TV con tomas de A/V1 Unsnap the battery cover from the AccessoriesInstalling Batteries Check the following accessories when unpacking the STB2 Number buttons 3 OK button Remote ControlLocation of Controls Ubicación del controlRear Panel 1 Remote control sensor 2 POWER indicator1 AC power cord Front Panelwhite red yellow A Connecting to a TV without A/V JacksB Connecting to a TV with A/V Jacks Connectionsy ellow C Connecting to a Cable Box OptionalNote to the Cable TV System Installer whiteon the STB to the audio input jack on the DVD D Connecting to Other DevicesConexión a otros dispositivos red yellow”SETUP WIZARD” screen automatically appears Initial Setup Setup WizardInitial Setup 1 Press STANDBY-ON on the remote control to activate the STB9 Select “AUTOSCAN” using K / L, then press OK 3 Select “CONTINUE” using s / B, then press OK4 Select the language using K / L, then press OK 6 Select your time zone using K / L, then press OK“NO SIGNAL” appears after the sub-channel broadcast is over using CH K / LIf the main channel number is 1 digit, press . when finish entering If the sub-channel number is 1 digit, press OK when finish enteringChoosing Audio Language To cancel still modePress AUDIO repeatedly Press STILL1 Press EPG while watching TV 2 Select the desired program using s / Bprovide signals for “EPG” Press DISPLAY1 Press SETUP 1 Press SETUP 2 Select “CHANNEL” using K / L, then press OK3 Select “AUTOSCAN” using K / L, then press OK 4 Select “AUTOSCAN” using K / L, then press OKOperation 6 Press SETUP to exit4 Select “DELETE” using K / L, then press OK 5 Press OK again to add the channel to the channel map1 Press SETUP 2 Select “DETAIL” using K / L, then press OK Adjusting Antenna2 Press SETUP 3 Select “CHANNEL” using K / L, then press OK 4 Select “ANTENNA” using K / L, then press OK4 Select your time zone using K / L , then press OK Setting the Time Zone and D.S.T Daylight Saving Time1 Press SETUP 2 Select “TIME” using K / L , then press OK 3 Select “TIME ZONE” using K / L , then press OK3 Select “V-CHIP” using K / L , then press OK 3 Select “D.S.T” using K / L , then press OK4 Select “ON” or “OFF” using s / B , then press OK 1 Press SETUP 2 Select “DETAIL” using K / L , then press OKMPAA Rating 5 Select the desired rating type using K / L , then press OK6 Select the desired rating using K / L , then press OK repeatedly to switch between view and block6 Enter the new 4-digit password using the Number buttons 7 Press SETUP to exit4 Enter 4737 in the password entry field 5 Select “NEW PASSWORD” using K / L , then press OK5 Select the desired DTV closed caption using K / L , then press OK 5 Select “MANUAL” using K / L , then press OK3 Select “CLOSED CAPTION” using K / L , then press OK 4 Select the desired closed caption item using K / L , then press OK3 Select “AUTO POWER DOWN” using K / L , then press OK Auto Power Down4 Select desired amount of time using K / L , then press OK Viewing Analog TV You can view analog TV by switching “RF OUT” settingYou cannot view Digital TV with this setting You cannot view Analog TV with this setting3 Select the desired channel on your TV You can view analog TV without switching “RF OUT” settingMethod 2 Método 2 Select “RF THROUGH” in “RF OUT”3 Select “RF OUT” using K / L, then press OK Setting RF OUTUsing SETUP to Switch “RF OUT” Setting 2 Select “CHANNEL” using K / L, then press OKLow volume TroubleshootingNo power to the remote controlPower Consumption SpecificationsConnecting Jacks ANT. IN/OUT Power SourceCustomer Service LIMITED WARRANTYWARRANTY STATEMENT REGARDING NON AUTHORIZED REPAIRS FUNAI SERVICE CORPORATION