Magnavox TB110MW9 Information on Digital Broadcasting, Accessories, Installing Batteries, pilas

Page 7
Information on Digital Broadcasting

Information on Digital Broadcasting

Before Using

Receives

ATSC

ATSC

 

Digital

Digital terrestrialterrestrial signals antenna

STB (Set Top Box)

converts the ATSC signal to analog signal

TV

This STB makes it possible to view the digital TV programs on your analog TV by converting the digital signal to the analog signal. You can use most features provided by the digital broadcast, except that the resolution of the image is always output in 480i (standard resolution).

Accessories

Check the following accessories when unpacking the STB:

Remote control:

Owner’s manual:

AA battery (x2)

RF cable:

NA386UD (x1)

1VMN25977 (x1)

 

WPZ0901TM002 /

 

 

 

WPZ0901TM005 (x1)

Installing Batteries

Instalación de pilas

1 Unsnap the battery cover from the

2 Install two AA batteries making
3 Snap the battery
back of the remote control.
sure the polarity (+ / - ) is correct.
cover back.
Abra la cubierta de pilas de la parte

Instale dos pilas AA asegurándose que

Cierre la cubierta de

trasera del mando a distancia.
la polaridad (+ / - ) sea la correcta.
pilas.

NOTE:

When replacing batteries, replace them in pairs.

Cuando cambie las pilas, hágalo por pares.

CAUTION:

Do not mix battery types (alkaline and manganese, or old ones and new ones).

No mezcle tipos de baterías (baterías alcalinas y de manganeso, ni pilas viejas con pilas nuevas).

Do not recharge, short-circuit, heat, burn or disassemble batteries.

No recargue, caliente, queme o desarme baterías ni provoque un corto circuito con ellas.

Remove batteries from battery compartment that is not going to be used for a month or more.

Quite las pilas del compartimento de pilas si no se va a utilizar durante un mes o más.

7

EN

Image 7
Contents DTV Digital to Analog Converter Set Top Box INSTRUCCIONES EN ESPAÑOL INCLUIDASTHAT MAKE USING YOUR MAGNAVOX PRODUCT MORE ENJOYABLE TB110MW9Important Safeguards Before UsingRISK OF ELECTRIC SHOCK DO NOT OPEN Model No Before UsingINSERT Dealer Phone NoAvoid the Hazards of Electrical Shock and Fire PrecautionsInstall the product in a horizontal position LocationAdvanced Operation Before UsingInitial Setup Setup Wizard T a b l e o f C o n t e n t sConexión a una caja de cable OverviewConexión a un TV sin tomas de A/V Conexión a un TV con tomas de A/V1 Unsnap the battery cover from the AccessoriesInstalling Batteries Check the following accessories when unpacking the STB2 Number buttons 3 OK button Remote ControlLocation of Controls Ubicación del controlRear Panel 1 Remote control sensor 2 POWER indicator1 AC power cord Front Panelwhite red yellow A Connecting to a TV without A/V JacksB Connecting to a TV with A/V Jacks Connectionsy ellow C Connecting to a Cable Box OptionalNote to the Cable TV System Installer whiteon the STB to the audio input jack on the DVD D Connecting to Other DevicesConexión a otros dispositivos red yellow”SETUP WIZARD” screen automatically appears Initial Setup Setup WizardInitial Setup 1 Press STANDBY-ON on the remote control to activate the STB9 Select “AUTOSCAN” using K / L, then press OK 3 Select “CONTINUE” using s / B, then press OK4 Select the language using K / L, then press OK 6 Select your time zone using K / L, then press OK“NO SIGNAL” appears after the sub-channel broadcast is over using CH K / LIf the main channel number is 1 digit, press . when finish entering If the sub-channel number is 1 digit, press OK when finish enteringChoosing Audio Language To cancel still modePress AUDIO repeatedly Press STILL1 Press EPG while watching TV 2 Select the desired program using s / Bprovide signals for “EPG” Press DISPLAY1 Press SETUP 1 Press SETUP 2 Select “CHANNEL” using K / L, then press OK3 Select “AUTOSCAN” using K / L, then press OK 4 Select “AUTOSCAN” using K / L, then press OKOperation 6 Press SETUP to exit4 Select “DELETE” using K / L, then press OK 5 Press OK again to add the channel to the channel map1 Press SETUP 2 Select “DETAIL” using K / L, then press OK Adjusting Antenna2 Press SETUP 3 Select “CHANNEL” using K / L, then press OK 4 Select “ANTENNA” using K / L, then press OK4 Select your time zone using K / L , then press OK Setting the Time Zone and D.S.T Daylight Saving Time1 Press SETUP 2 Select “TIME” using K / L , then press OK 3 Select “TIME ZONE” using K / L , then press OK3 Select “V-CHIP” using K / L , then press OK 3 Select “D.S.T” using K / L , then press OK4 Select “ON” or “OFF” using s / B , then press OK 1 Press SETUP 2 Select “DETAIL” using K / L , then press OKMPAA Rating 5 Select the desired rating type using K / L , then press OK6 Select the desired rating using K / L , then press OK repeatedly to switch between view and block6 Enter the new 4-digit password using the Number buttons 7 Press SETUP to exit4 Enter 4737 in the password entry field 5 Select “NEW PASSWORD” using K / L , then press OK5 Select the desired DTV closed caption using K / L , then press OK 5 Select “MANUAL” using K / L , then press OK3 Select “CLOSED CAPTION” using K / L , then press OK 4 Select the desired closed caption item using K / L , then press OK3 Select “AUTO POWER DOWN” using K / L , then press OK Auto Power Down4 Select desired amount of time using K / L , then press OK Viewing Analog TV You can view analog TV by switching “RF OUT” settingYou cannot view Digital TV with this setting You cannot view Analog TV with this setting3 Select the desired channel on your TV You can view analog TV without switching “RF OUT” settingMethod 2 Método 2 Select “RF THROUGH” in “RF OUT”3 Select “RF OUT” using K / L, then press OK Setting RF OUTUsing SETUP to Switch “RF OUT” Setting 2 Select “CHANNEL” using K / L, then press OKLow volume TroubleshootingNo power to the remote controlPower Consumption SpecificationsConnecting Jacks ANT. IN/OUT Power SourceCustomer Service LIMITED WARRANTYWARRANTY STATEMENT REGARDING NON AUTHORIZED REPAIRS FUNAI SERVICE CORPORATION