Magnavox TB110MW9 Select the desired rating type using K / L , then press OK, MPAA Rating, higher

Page 23

5Select the desired rating type using [ K / L ], then press [OK].

5Select the desired rating type using [ K / L ], then press [OK].

E.g., “TV RATING”

V-CHIP

EXIT		MPAA RATING

CHANNEL		TV RATING
TIME		CANADIAN ENGLISH RATING
		CANADIAN FRENCH RATING
DETAIL		DOWNLOADABLE RATING
		CLEAR DOWNLOADABLE RATING

INITIAL		NEW PASSWORD

NOTE:

•“DOWNLOADABLE RATING” will be available when the STB receives a digital broadcast which contains V-chip 2.0 signal.

•If the broadcasting signal does not have the downloadable rating information, “Downloadable Rating is currently not available.” will appear.

This message will also appear when you try to access “DOWNLOADABLE RATING” after you have cleared the downloadable rating information, and the new information has not been downloaded since.

•To clear the downloadable rating information and its setting, select “CLEAR DOWNLOADABLE RATING”.

6Select the desired rating using

[ K / L ], then press [OK] repeatedly to switch between view and block.

• When the rating is blocked, will appear.

MPAA Rating

Rating	Description
X	Mature audience only	higher
NC-17	No one under 17 admitted

Restricted; under 17 requires

Raccompanying parent or adult guardian

PG-13	Unsuitable for children under 13
PG	Parental guidance suggested
G	General audience		lower
NR	No rating

TV Rating

Rating		Description
TV-MA	Mature audience only		higher
TV-14	Unsuitable for children under
TV-14	14
	14
TV-PG	Parental guidance suggested
TV-G	General audience
TV-Y7	Appropriate for all children 7
TV-Y7	and older
	and older
TV-Y	Appropriate for all children		lower
None	No rating

Operation	Advanced

E.g.,

“MPAA rating”

V-CHIP

Select MPAA rating.

EXIT

X

CHANNEL NC-17

R

TIME PG-13

PG

DETAIL G

“TV rating”

V-CHIP

Set TV rating.

EXIT

FV

V

S

L

D

CHANNEL

TV-MA

TV-14

TIME

TV-PG

TV-G

DETAIL

TV-Y7

TV-Y

INITIAL

NR

INITIAL

None

“Canadian English rating” “Canadian French rating”

V-CHIP						V-CHIP

		Set Canadian English rating.						Set Canadian French rating.
EXIT		18+				EXIT		18ans+
		18+						18ans+
CHANNEL		14+				CHANNEL		16ans+
		PG						13ans+
TIME						TIME
TIME		G				TIME		8ans+
DETAIL		C8+				DETAIL		G
DETAIL		C				DETAIL		E
INITIAL		E				INITIAL

23

EN

Image 23

Contents DTV Digital to Analog Converter Set Top Box INSTRUCCIONES EN ESPAÑOL INCLUIDASTHAT MAKE USING YOUR MAGNAVOX PRODUCT MORE ENJOYABLE TB110MW9RISK OF ELECTRIC SHOCK DO NOT OPEN Before UsingImportant Safeguards Model No Before UsingINSERT Dealer Phone NoAvoid the Hazards of Electrical Shock and Fire PrecautionsInstall the product in a horizontal position LocationAdvanced Operation Before UsingInitial Setup Setup Wizard T a b l e o f C o n t e n t sConexión a una caja de cable OverviewConexión a un TV sin tomas de A/V Conexión a un TV con tomas de A/V1 Unsnap the battery cover from the AccessoriesInstalling Batteries Check the following accessories when unpacking the STB2 Number buttons 3 OK button Remote ControlLocation of Controls Ubicación del controlRear Panel 1 Remote control sensor 2 POWER indicator1 AC power cord Front Panelwhite red yellow A Connecting to a TV without A/V JacksB Connecting to a TV with A/V Jacks Connectionsy ellow C Connecting to a Cable Box OptionalNote to the Cable TV System Installer whiteon the STB to the audio input jack on the DVD D Connecting to Other DevicesConexión a otros dispositivos red yellow”SETUP WIZARD” screen automatically appears Initial Setup Setup WizardInitial Setup 1 Press STANDBY-ON on the remote control to activate the STB9 Select “AUTOSCAN” using K / L, then press OK 3 Select “CONTINUE” using s / B, then press OK4 Select the language using K / L, then press OK 6 Select your time zone using K / L, then press OK“NO SIGNAL” appears after the sub-channel broadcast is over using CH K / LIf the main channel number is 1 digit, press . when finish entering If the sub-channel number is 1 digit, press OK when finish enteringChoosing Audio Language To cancel still modePress AUDIO repeatedly Press STILL1 Press EPG while watching TV 2 Select the desired program using s / Bprovide signals for “EPG” Press DISPLAY1 Press SETUP 1 Press SETUP 2 Select “CHANNEL” using K / L, then press OK3 Select “AUTOSCAN” using K / L, then press OK 4 Select “AUTOSCAN” using K / L, then press OKOperation 6 Press SETUP to exit4 Select “DELETE” using K / L, then press OK 5 Press OK again to add the channel to the channel map1 Press SETUP 2 Select “DETAIL” using K / L, then press OK Adjusting Antenna2 Press SETUP 3 Select “CHANNEL” using K / L, then press OK 4 Select “ANTENNA” using K / L, then press OK4 Select your time zone using K / L , then press OK Setting the Time Zone and D.S.T Daylight Saving Time1 Press SETUP 2 Select “TIME” using K / L , then press OK 3 Select “TIME ZONE” using K / L , then press OK3 Select “V-CHIP” using K / L , then press OK 3 Select “D.S.T” using K / L , then press OK4 Select “ON” or “OFF” using s / B , then press OK 1 Press SETUP 2 Select “DETAIL” using K / L , then press OKMPAA Rating 5 Select the desired rating type using K / L , then press OK6 Select the desired rating using K / L , then press OK repeatedly to switch between view and block6 Enter the new 4-digit password using the Number buttons 7 Press SETUP to exit4 Enter 4737 in the password entry field 5 Select “NEW PASSWORD” using K / L , then press OK5 Select the desired DTV closed caption using K / L , then press OK 5 Select “MANUAL” using K / L , then press OK3 Select “CLOSED CAPTION” using K / L , then press OK 4 Select the desired closed caption item using K / L , then press OK4 Select desired amount of time using K / L , then press OK Auto Power Down3 Select “AUTO POWER DOWN” using K / L , then press OK Viewing Analog TV You can view analog TV by switching “RF OUT” settingYou cannot view Digital TV with this setting You cannot view Analog TV with this setting3 Select the desired channel on your TV You can view analog TV without switching “RF OUT” settingMethod 2 Método 2 Select “RF THROUGH” in “RF OUT”3 Select “RF OUT” using K / L, then press OK Setting RF OUTUsing SETUP to Switch “RF OUT” Setting 2 Select “CHANNEL” using K / L, then press OKLow volume TroubleshootingNo power to the remote controlPower Consumption SpecificationsConnecting Jacks ANT. IN/OUT Power SourceCustomer Service LIMITED WARRANTYWARRANTY STATEMENT REGARDING NON AUTHORIZED REPAIRS FUNAI SERVICE CORPORATION