Magnavox TB110MW9 Initial Setup Setup Wizard, Ajùste inicial, Appropriate Viewing Channel

Page 13

Initial Setup (Setup Wizard)

Initial Setup (Setup Wizard)

Initial Setup

Ajùste inicial

1 Press [STANDBY-ON] on the remote control to activate the STB.

Presione [STANDBY-ON] en el mando a distancia para activar el STB.

lights up in green

se vuelve verde

2Turn on the TV, and select the viewing channel (ch3 or external input channel) on your TV. (Refer to your TV’s manual.)

Encienda el TV, y seleccione el canal que quiera ver (canal 3 o uno de entrada externo) en su TV. (Véase el manual del TV.)

2

1

Appropriate Viewing Channel

Configuración apropiada de el Canal de Visión

	Viewing	STB	Cable Box	DVD or VCR
	Connection

	A (p.10)	“CH3”	-	-
	B (p.10)	External input channel	-	-
		Canal de entrada externo

	C (p.11)	External input channel	Ch3	-
		Canal de entrada externo

	D (p.12)	“CH3”	-	External input channel
				Canal de entrada externo

•If your TV’s ch3 is already occupied, select ch4, and set the STB’s output channel to ch4. You can switch ch3 / ch4 by holding [SETUP] down over 3 seconds.

Si el c3 de su TV ya está ocupado, seleccione el c4 y luego ajuste el canal de salida del STB a c4. Puede alternar entre el c3 y 4 manteniendo presionado [SETUP] durante 3 segundos.

”SETUP WIZARD” screen automatically appears.Follow the directions shown on the TV screen to set the each setting.

13

Initial Setup (Setup Wizard)

EN

Image 13

Contents THAT MAKE USING YOUR MAGNAVOX PRODUCT MORE ENJOYABLE INSTRUCCIONES EN ESPAÑOL INCLUIDASTB110MW9 DTV Digital to Analog Converter Set Top BoxImportant Safeguards Before UsingRISK OF ELECTRIC SHOCK DO NOT OPEN INSERT Before UsingDealer Phone No Model NoInstall the product in a horizontal position PrecautionsLocation Avoid the Hazards of Electrical Shock and FireInitial Setup Setup Wizard Before UsingT a b l e o f C o n t e n t s Advanced OperationConexión a un TV sin tomas de A/V OverviewConexión a un TV con tomas de A/V Conexión a una caja de cableInstalling Batteries AccessoriesCheck the following accessories when unpacking the STB 1 Unsnap the battery cover from theLocation of Controls Remote ControlUbicación del control 2 Number buttons 3 OK button1 AC power cord 1 Remote control sensor 2 POWER indicatorFront Panel Rear PanelB Connecting to a TV with A/V Jacks A Connecting to a TV without A/V JacksConnections white red yellowNote to the Cable TV System Installer C Connecting to a Cable Box Optionalwhite y ellowConexión a otros dispositivos D Connecting to Other Devicesred yellow on the STB to the audio input jack on the DVDInitial Setup Initial Setup Setup Wizard1 Press STANDBY-ON on the remote control to activate the STB ”SETUP WIZARD” screen automatically appears4 Select the language using K / L, then press OK 3 Select “CONTINUE” using s / B, then press OK6 Select your time zone using K / L, then press OK 9 Select “AUTOSCAN” using K / L, then press OKIf the main channel number is 1 digit, press . when finish entering using CH K / LIf the sub-channel number is 1 digit, press OK when finish entering “NO SIGNAL” appears after the sub-channel broadcast is overPress AUDIO repeatedly To cancel still modePress STILL Choosing Audio Languageprovide signals for “EPG” 2 Select the desired program using s / BPress DISPLAY 1 Press EPG while watching TV3 Select “AUTOSCAN” using K / L, then press OK 1 Press SETUP 2 Select “CHANNEL” using K / L, then press OK4 Select “AUTOSCAN” using K / L, then press OK 1 Press SETUP4 Select “DELETE” using K / L, then press OK 6 Press SETUP to exit5 Press OK again to add the channel to the channel map Operation2 Press SETUP 3 Select “CHANNEL” using K / L, then press OK Adjusting Antenna4 Select “ANTENNA” using K / L, then press OK 1 Press SETUP 2 Select “DETAIL” using K / L, then press OK1 Press SETUP 2 Select “TIME” using K / L , then press OK Setting the Time Zone and D.S.T Daylight Saving Time3 Select “TIME ZONE” using K / L , then press OK 4 Select your time zone using K / L , then press OK4 Select “ON” or “OFF” using s / B , then press OK 3 Select “D.S.T” using K / L , then press OK1 Press SETUP 2 Select “DETAIL” using K / L , then press OK 3 Select “V-CHIP” using K / L , then press OK6 Select the desired rating using 5 Select the desired rating type using K / L , then press OKK / L , then press OK repeatedly to switch between view and block MPAA Rating4 Enter 4737 in the password entry field 7 Press SETUP to exit5 Select “NEW PASSWORD” using K / L , then press OK 6 Enter the new 4-digit password using the Number buttons3 Select “CLOSED CAPTION” using K / L , then press OK 5 Select “MANUAL” using K / L , then press OK4 Select the desired closed caption item using K / L , then press OK 5 Select the desired DTV closed caption using K / L , then press OK3 Select “AUTO POWER DOWN” using K / L , then press OK Auto Power Down4 Select desired amount of time using K / L , then press OK You cannot view Digital TV with this setting You can view analog TV by switching “RF OUT” settingYou cannot view Analog TV with this setting Viewing Analog TVMethod 2 Método You can view analog TV without switching “RF OUT” setting2 Select “RF THROUGH” in “RF OUT” 3 Select the desired channel on your TVUsing SETUP to Switch “RF OUT” Setting Setting RF OUT2 Select “CHANNEL” using K / L, then press OK 3 Select “RF OUT” using K / L, then press OKNo power Troubleshootingto the remote control Low volumeConnecting Jacks ANT. IN/OUT SpecificationsPower Source Power ConsumptionWARRANTY STATEMENT REGARDING NON AUTHORIZED REPAIRS LIMITED WARRANTYFUNAI SERVICE CORPORATION Customer Service