Magnavox TB110MW9 Information on Display Mode, Select “TIME ZONE” using K / L , then press OK

Page 21

Information on Display Mode

Information on Display Mode

LETTERBOX

16:9 picture is scaled down until the both sides of the picture fits the 4:3 TV. Black bars appear on top and bottom of the TV screen.

ZOOM

Displays the 16:9 image with the top and the bottom of the picture fit to the 4:3 TV screen. Both sides of the picture are cut off.

FULL

16:9 image is squeezed into the 4:3 TV screen. No parts are cropped, but the picture gets distorted.

CAUTION:

If the TV is left in LETTER BOX mode for a long period of time, the black bars may cause a permanent burn- in effect.

Setting the Time Zone and D.S.T (Daylight Saving Time)

You need to select the time zone of your area and set D.S.T correctly to make use of the EPG and the Channel banner function.

1 Press [SETUP].

2Select “TIME” using [ K / L ], then press [OK].

Time Zone

3Select “TIME ZONE” using [ K / L ], then press [OK].

TIME

EXIT
		TIME ZONE	EASTERN
CHANNEL		D.S.T	OFF

TIME
TIME
DETAIL
INITIAL

4 Select your time zone using [ K / L ], then press [OK].

Select Time Zone.

ATLANTIC

EASTERN

CENTRAL

MOUNTAIN

PACIFIC

ALASKA

HAWAII

5 Press [SETUP] to exit.





	Operation	Advanced

21

EN

Image 21

Contents THAT MAKE USING YOUR MAGNAVOX PRODUCT MORE ENJOYABLE INSTRUCCIONES EN ESPAÑOL INCLUIDASTB110MW9 DTV Digital to Analog Converter Set Top BoxBefore Using Important SafeguardsRISK OF ELECTRIC SHOCK DO NOT OPEN INSERT Before UsingDealer Phone No Model NoInstall the product in a horizontal position PrecautionsLocation Avoid the Hazards of Electrical Shock and FireInitial Setup Setup Wizard Before UsingT a b l e o f C o n t e n t s Advanced OperationConexión a un TV sin tomas de A/V OverviewConexión a un TV con tomas de A/V Conexión a una caja de cableInstalling Batteries AccessoriesCheck the following accessories when unpacking the STB 1 Unsnap the battery cover from theLocation of Controls Remote ControlUbicación del control 2 Number buttons 3 OK button1 AC power cord 1 Remote control sensor 2 POWER indicatorFront Panel Rear PanelB Connecting to a TV with A/V Jacks A Connecting to a TV without A/V JacksConnections white red yellowNote to the Cable TV System Installer C Connecting to a Cable Box Optionalwhite y ellowConexión a otros dispositivos D Connecting to Other Devicesred yellow on the STB to the audio input jack on the DVDInitial Setup Initial Setup Setup Wizard1 Press STANDBY-ON on the remote control to activate the STB ”SETUP WIZARD” screen automatically appears4 Select the language using K / L, then press OK 3 Select “CONTINUE” using s / B, then press OK6 Select your time zone using K / L, then press OK 9 Select “AUTOSCAN” using K / L, then press OKIf the main channel number is 1 digit, press . when finish entering using CH K / LIf the sub-channel number is 1 digit, press OK when finish entering “NO SIGNAL” appears after the sub-channel broadcast is overPress AUDIO repeatedly To cancel still modePress STILL Choosing Audio Languageprovide signals for “EPG” 2 Select the desired program using s / BPress DISPLAY 1 Press EPG while watching TV3 Select “AUTOSCAN” using K / L, then press OK 1 Press SETUP 2 Select “CHANNEL” using K / L, then press OK4 Select “AUTOSCAN” using K / L, then press OK 1 Press SETUP4 Select “DELETE” using K / L, then press OK 6 Press SETUP to exit5 Press OK again to add the channel to the channel map Operation2 Press SETUP 3 Select “CHANNEL” using K / L, then press OK Adjusting Antenna4 Select “ANTENNA” using K / L, then press OK 1 Press SETUP 2 Select “DETAIL” using K / L, then press OK1 Press SETUP 2 Select “TIME” using K / L , then press OK Setting the Time Zone and D.S.T Daylight Saving Time3 Select “TIME ZONE” using K / L , then press OK 4 Select your time zone using K / L , then press OK4 Select “ON” or “OFF” using s / B , then press OK 3 Select “D.S.T” using K / L , then press OK1 Press SETUP 2 Select “DETAIL” using K / L , then press OK 3 Select “V-CHIP” using K / L , then press OK6 Select the desired rating using 5 Select the desired rating type using K / L , then press OKK / L , then press OK repeatedly to switch between view and block MPAA Rating4 Enter 4737 in the password entry field 7 Press SETUP to exit5 Select “NEW PASSWORD” using K / L , then press OK 6 Enter the new 4-digit password using the Number buttons3 Select “CLOSED CAPTION” using K / L , then press OK 5 Select “MANUAL” using K / L , then press OK4 Select the desired closed caption item using K / L , then press OK 5 Select the desired DTV closed caption using K / L , then press OKAuto Power Down 3 Select “AUTO POWER DOWN” using K / L , then press OK4 Select desired amount of time using K / L , then press OK You cannot view Digital TV with this setting You can view analog TV by switching “RF OUT” settingYou cannot view Analog TV with this setting Viewing Analog TVMethod 2 Método You can view analog TV without switching “RF OUT” setting2 Select “RF THROUGH” in “RF OUT” 3 Select the desired channel on your TVUsing SETUP to Switch “RF OUT” Setting Setting RF OUT2 Select “CHANNEL” using K / L, then press OK 3 Select “RF OUT” using K / L, then press OKNo power Troubleshootingto the remote control Low volumeConnecting Jacks ANT. IN/OUT SpecificationsPower Source Power ConsumptionWARRANTY STATEMENT REGARDING NON AUTHORIZED REPAIRS LIMITED WARRANTYFUNAI SERVICE CORPORATION Customer Service