Magnavox TB110MW9 Viewing Analog TV, Method 1 Método, Select “CH3” in “RF OUT” menu, Connection

Page 27

Viewing Analog TV

Viewing Analog TV

Viendo TV Analógica

Method 1 Método 1

You can view analog TV by switching “RF OUT” setting.

Usted podrá ver TV analógica cambiando la configuración de “SALIDA RF”.

CONNECTIONCONEXIÓNTV

STB

TV antenna

Antena de TV

RF cable (supplied)

cable de RF (se incluye)

Viewing Analog TVViendo TV Analógica1 Press [STANDBY-ON] to activate the STB.Presione [STANDBY-ON] para activar el STB.

2 Select “RF THROUGH” in “RF OUT”

menu. ( Page 29)Seleccione“TRAVÉS DE RF”en el menú“SALIDA RF”.

3 Select the desired channel on your TV.

Seleccione el canal deseado en su TV.ch4

ch6

ch8

You can view analog TV on your TV channel.

Usted podrá ver TV analógica en su canal de TV.

NOTE:

•You cannot view Digital TV with this setting.

•With this setting, the analog TV signal can directly be sent to your TV.

Viewing Digital TVViendo TV Digital

1 Press [STANDBY-ON] to activate the STB.

Presione [STANDBY-ON] para activar el STB.

2 Select “CH3” in “RF OUT” menu.

( Page 29)Seleccione “CH3” en el menú “SALIDA RF”.

3 Select ch3 on your TV.

Seleccione canal3 en su TV.

ch3

You can view digital TV on ch3 of your TV.

Usted podrá ver TV digital en el c3 de su TV.

4 Select desired channel on the STB.

Seleccione el canal deseado en el STB.ch3

ch3

ch3

NOTE:

•You cannot view Analog TV with this setting.

•You can switch “RF THROUGH” to “CH3” by holding [SET UP] down over 3 seconds.

Holding [SETUP] down over 3 seconds does not switch the setting back to “RF THROUGH”.

27	To switch the setting back to “RF THROUGH”, follow
	the steps in “Setting RF OUT” on page 29.

Operation	Advanced

EN

Image 27

Contents DTV Digital to Analog Converter Set Top Box INSTRUCCIONES EN ESPAÑOL INCLUIDASTHAT MAKE USING YOUR MAGNAVOX PRODUCT MORE ENJOYABLE TB110MW9Before Using Important SafeguardsRISK OF ELECTRIC SHOCK DO NOT OPEN Model No Before UsingINSERT Dealer Phone NoAvoid the Hazards of Electrical Shock and Fire PrecautionsInstall the product in a horizontal position LocationAdvanced Operation Before UsingInitial Setup Setup Wizard T a b l e o f C o n t e n t sConexión a una caja de cable OverviewConexión a un TV sin tomas de A/V Conexión a un TV con tomas de A/V1 Unsnap the battery cover from the AccessoriesInstalling Batteries Check the following accessories when unpacking the STB2 Number buttons 3 OK button Remote ControlLocation of Controls Ubicación del controlRear Panel 1 Remote control sensor 2 POWER indicator1 AC power cord Front Panelwhite red yellow A Connecting to a TV without A/V JacksB Connecting to a TV with A/V Jacks Connectionsy ellow C Connecting to a Cable Box OptionalNote to the Cable TV System Installer whiteon the STB to the audio input jack on the DVD D Connecting to Other DevicesConexión a otros dispositivos red yellow”SETUP WIZARD” screen automatically appears Initial Setup Setup WizardInitial Setup 1 Press STANDBY-ON on the remote control to activate the STB9 Select “AUTOSCAN” using K / L, then press OK 3 Select “CONTINUE” using s / B, then press OK4 Select the language using K / L, then press OK 6 Select your time zone using K / L, then press OK“NO SIGNAL” appears after the sub-channel broadcast is over using CH K / LIf the main channel number is 1 digit, press . when finish entering If the sub-channel number is 1 digit, press OK when finish enteringChoosing Audio Language To cancel still modePress AUDIO repeatedly Press STILL1 Press EPG while watching TV 2 Select the desired program using s / Bprovide signals for “EPG” Press DISPLAY1 Press SETUP 1 Press SETUP 2 Select “CHANNEL” using K / L, then press OK3 Select “AUTOSCAN” using K / L, then press OK 4 Select “AUTOSCAN” using K / L, then press OKOperation 6 Press SETUP to exit4 Select “DELETE” using K / L, then press OK 5 Press OK again to add the channel to the channel map1 Press SETUP 2 Select “DETAIL” using K / L, then press OK Adjusting Antenna2 Press SETUP 3 Select “CHANNEL” using K / L, then press OK 4 Select “ANTENNA” using K / L, then press OK4 Select your time zone using K / L , then press OK Setting the Time Zone and D.S.T Daylight Saving Time1 Press SETUP 2 Select “TIME” using K / L , then press OK 3 Select “TIME ZONE” using K / L , then press OK3 Select “V-CHIP” using K / L , then press OK 3 Select “D.S.T” using K / L , then press OK4 Select “ON” or “OFF” using s / B , then press OK 1 Press SETUP 2 Select “DETAIL” using K / L , then press OKMPAA Rating 5 Select the desired rating type using K / L , then press OK6 Select the desired rating using K / L , then press OK repeatedly to switch between view and block6 Enter the new 4-digit password using the Number buttons 7 Press SETUP to exit4 Enter 4737 in the password entry field 5 Select “NEW PASSWORD” using K / L , then press OK5 Select the desired DTV closed caption using K / L , then press OK 5 Select “MANUAL” using K / L , then press OK3 Select “CLOSED CAPTION” using K / L , then press OK 4 Select the desired closed caption item using K / L , then press OKAuto Power Down 3 Select “AUTO POWER DOWN” using K / L , then press OK4 Select desired amount of time using K / L , then press OK Viewing Analog TV You can view analog TV by switching “RF OUT” settingYou cannot view Digital TV with this setting You cannot view Analog TV with this setting3 Select the desired channel on your TV You can view analog TV without switching “RF OUT” settingMethod 2 Método 2 Select “RF THROUGH” in “RF OUT”3 Select “RF OUT” using K / L, then press OK Setting RF OUTUsing SETUP to Switch “RF OUT” Setting 2 Select “CHANNEL” using K / L, then press OKLow volume TroubleshootingNo power to the remote controlPower Consumption SpecificationsConnecting Jacks ANT. IN/OUT Power SourceCustomer Service LIMITED WARRANTYWARRANTY STATEMENT REGARDING NON AUTHORIZED REPAIRS FUNAI SERVICE CORPORATION