Magnavox TB110MW9 Others, Troubleshooting, No power, The STB is not responding, Low volume

Page 30

Others

Others

Troubleshooting

Before requesting service, check the table below for a possible cause of the problem.

Symptom

Remedy

	No power	•	Make sure that the AC power cord is securely plugged into the power
	No power		outlet.
			outlet.

		• Make sure to point the remote control at the remote control sensor.
		• You may be too far from STB. Try moving closer.
	The STB is not responding	• Remove any obstacles between the remote control and the remote
	The STB is not responding		control sensor.
	to the remote control.		control sensor.
	to the remote control.	• Make sure that the batteries are installed in the correct direction

			(+ and –). ( Page 7.)
		• The batteries may be depleted. Replace them with new ones.
		• Make sure that the audio / video cables are correctly connected.
		• Make sure that the TV is turned on.
	No audio / picture	• Make sure that the correct viewing channel (ch3 or external input
	No audio / picture		channel) is selected on your TV. ( Page 13.) Refer to your TV’s manual
			for further information.
		• Make sure the cables are not damaged.
		•	Make sure “RF OUT” setting is correct. ( Page 29.)
	Blocked noise on picture	•	Make sure that the RF cable is connected correctly. (	Pages 10 - 12.)
	No EPG or the provided	•	Make sure that “D.S.T” and “TIME ZONE” is set correctly. ( Page 21.)
	information is wrong
	Low volume	•	Sound volume differs depending on the audio out setting. Select “RF
	Low volume		OUT” at step 5 in the “Initial Setup (Setup Wizard)”. (	Page 14.)
			OUT” at step 5 in the “Initial Setup (Setup Wizard)”. (	Page 14.)
		• Make sure to complete autoscan in “SETUP WIZARD” or in “SETUP”
			menu. When autoscan is not completed, some channels will not be
		•	received.
	No reception	•	The selected channel does not exist at that time. There are not always
			sub-channels being broadcast.
		• Some channels with weak signal may not be received properly.
			This is not a malfunction.
	When you forget the	•	If you forget the password, refer to “New Password”. (	Page 24.)
	password for V-chip
	Closed captioning display	•	Change the channel on your TV.
	(TEXT mode) does not go	•	Turn the TV off, and then on.
	off even after changing
	channels through STB.
	The TV screen goes blank	•	This is a normal part of the start-up process and is not a malfunction.
	just after turning the STB
	on.

30

EN

Image 30

Contents TB110MW9 INSTRUCCIONES EN ESPAÑOL INCLUIDASTHAT MAKE USING YOUR MAGNAVOX PRODUCT MORE ENJOYABLE DTV Digital to Analog Converter Set Top BoxBefore Using Important SafeguardsRISK OF ELECTRIC SHOCK DO NOT OPEN Dealer Phone No Before UsingINSERT Model NoLocation PrecautionsInstall the product in a horizontal position Avoid the Hazards of Electrical Shock and FireT a b l e o f C o n t e n t s Before UsingInitial Setup Setup Wizard Advanced OperationConexión a un TV con tomas de A/V OverviewConexión a un TV sin tomas de A/V Conexión a una caja de cableCheck the following accessories when unpacking the STB AccessoriesInstalling Batteries 1 Unsnap the battery cover from theUbicación del control Remote ControlLocation of Controls 2 Number buttons 3 OK buttonFront Panel 1 Remote control sensor 2 POWER indicator1 AC power cord Rear PanelConnections A Connecting to a TV without A/V JacksB Connecting to a TV with A/V Jacks white red yellowwhite C Connecting to a Cable Box OptionalNote to the Cable TV System Installer y ellowred yellow D Connecting to Other DevicesConexión a otros dispositivos on the STB to the audio input jack on the DVD1 Press STANDBY-ON on the remote control to activate the STB Initial Setup Setup WizardInitial Setup ”SETUP WIZARD” screen automatically appears6 Select your time zone using K / L, then press OK 3 Select “CONTINUE” using s / B, then press OK4 Select the language using K / L, then press OK 9 Select “AUTOSCAN” using K / L, then press OKIf the sub-channel number is 1 digit, press OK when finish entering using CH K / LIf the main channel number is 1 digit, press . when finish entering “NO SIGNAL” appears after the sub-channel broadcast is overPress STILL To cancel still modePress AUDIO repeatedly Choosing Audio LanguagePress DISPLAY 2 Select the desired program using s / Bprovide signals for “EPG” 1 Press EPG while watching TV4 Select “AUTOSCAN” using K / L, then press OK 1 Press SETUP 2 Select “CHANNEL” using K / L, then press OK3 Select “AUTOSCAN” using K / L, then press OK 1 Press SETUP5 Press OK again to add the channel to the channel map 6 Press SETUP to exit4 Select “DELETE” using K / L, then press OK Operation4 Select “ANTENNA” using K / L, then press OK Adjusting Antenna2 Press SETUP 3 Select “CHANNEL” using K / L, then press OK 1 Press SETUP 2 Select “DETAIL” using K / L, then press OK3 Select “TIME ZONE” using K / L , then press OK Setting the Time Zone and D.S.T Daylight Saving Time1 Press SETUP 2 Select “TIME” using K / L , then press OK 4 Select your time zone using K / L , then press OK1 Press SETUP 2 Select “DETAIL” using K / L , then press OK 3 Select “D.S.T” using K / L , then press OK4 Select “ON” or “OFF” using s / B , then press OK 3 Select “V-CHIP” using K / L , then press OKK / L , then press OK repeatedly to switch between view and block 5 Select the desired rating type using K / L , then press OK6 Select the desired rating using MPAA Rating5 Select “NEW PASSWORD” using K / L , then press OK 7 Press SETUP to exit4 Enter 4737 in the password entry field 6 Enter the new 4-digit password using the Number buttons4 Select the desired closed caption item using K / L , then press OK 5 Select “MANUAL” using K / L , then press OK3 Select “CLOSED CAPTION” using K / L , then press OK 5 Select the desired DTV closed caption using K / L , then press OKAuto Power Down 3 Select “AUTO POWER DOWN” using K / L , then press OK4 Select desired amount of time using K / L , then press OK You cannot view Analog TV with this setting You can view analog TV by switching “RF OUT” settingYou cannot view Digital TV with this setting Viewing Analog TV2 Select “RF THROUGH” in “RF OUT” You can view analog TV without switching “RF OUT” settingMethod 2 Método 3 Select the desired channel on your TV2 Select “CHANNEL” using K / L, then press OK Setting RF OUTUsing SETUP to Switch “RF OUT” Setting 3 Select “RF OUT” using K / L, then press OKto the remote control TroubleshootingNo power Low volumePower Source SpecificationsConnecting Jacks ANT. IN/OUT Power ConsumptionFUNAI SERVICE CORPORATION LIMITED WARRANTYWARRANTY STATEMENT REGARDING NON AUTHORIZED REPAIRS Customer Service