Magnavox TB110MW9 Precautions, Location, Avoid the Hazards of Electrical Shock and Fire

Page 4

Precautions

Before Using

Precautions

Location

For safe operation and satisfactory performance of this product, keep the following in mind when selecting a place for its installation:

•Shield it from direct sunlight and keep it away from sources of intense heat.

•Avoid dusty or humid places.

•Avoid places with insufficient ventilation for proper heat dissipation. Do not block the ventilation holes at the top and bottom of the product. Do not place the product on a carpet because this will block the ventilation holes.

•Install the product in a horizontal position.

•Avoid locations subject to strong vibration.

•Do not place this product near strong magnetic fields.

Important Copyright Information

Unauthorized recording or use of broadcast television programming, video tape, film or other copyrighted material may violate applicable copyright laws. We assume no responsibility for the unauthorized duplication, use or other acts which infringe upon the rights of copyright owners.

FCC WARNING - This equipment may generate or use radio frequency energy. Changes or modifications to this equipment may cause harmful interference unless the modifications are expressly approved in the instruction manual. The user could lose the authority to operate this equipment if an unauthorized change or modification is made.

•Avoid moving this product to locations where temperature differences are extreme.

Avoid the Hazards of Electrical Shock and Fire

•

•

Do not handle the power cord with wet hands. Do not pull on the power cord when disconnecting it from an AC wall outlet. Grasp it by the plug.

•If by accident, water is spilled on your the product, unplug the power cord immediately and take the product to our Authorized Service Center for servicing.

•Do not place anything directly on top of the product.

A Note about Recycling

This product’s packaging materials are recyclable and can be reused. Please dispose of any materials in accordance with your local recycling regulations.

Batteries should never be thrown away or incinerated but disposed of in accordance with your local regulations concerning chemical wastes.

4

EN

Image 4

Contents INSTRUCCIONES EN ESPAÑOL INCLUIDAS THAT MAKE USING YOUR MAGNAVOX PRODUCT MORE ENJOYABLETB110MW9 DTV Digital to Analog Converter Set Top BoxImportant Safeguards Before UsingRISK OF ELECTRIC SHOCK DO NOT OPEN Before Using INSERTDealer Phone No Model NoPrecautions Install the product in a horizontal positionLocation Avoid the Hazards of Electrical Shock and FireBefore Using Initial Setup Setup WizardT a b l e o f C o n t e n t s Advanced OperationOverview Conexión a un TV sin tomas de A/VConexión a un TV con tomas de A/V Conexión a una caja de cableAccessories Installing BatteriesCheck the following accessories when unpacking the STB 1 Unsnap the battery cover from theRemote Control Location of ControlsUbicación del control 2 Number buttons 3 OK button1 Remote control sensor 2 POWER indicator 1 AC power cordFront Panel Rear PanelA Connecting to a TV without A/V Jacks B Connecting to a TV with A/V JacksConnections white red yellowC Connecting to a Cable Box Optional Note to the Cable TV System Installerwhite y ellowD Connecting to Other Devices Conexión a otros dispositivosred yellow on the STB to the audio input jack on the DVDInitial Setup Setup Wizard Initial Setup1 Press STANDBY-ON on the remote control to activate the STB ”SETUP WIZARD” screen automatically appears3 Select “CONTINUE” using s / B, then press OK 4 Select the language using K / L, then press OK6 Select your time zone using K / L, then press OK 9 Select “AUTOSCAN” using K / L, then press OKusing CH K / L If the main channel number is 1 digit, press . when finish enteringIf the sub-channel number is 1 digit, press OK when finish entering “NO SIGNAL” appears after the sub-channel broadcast is overTo cancel still mode Press AUDIO repeatedlyPress STILL Choosing Audio Language2 Select the desired program using s / B provide signals for “EPG”Press DISPLAY 1 Press EPG while watching TV1 Press SETUP 2 Select “CHANNEL” using K / L, then press OK 3 Select “AUTOSCAN” using K / L, then press OK4 Select “AUTOSCAN” using K / L, then press OK 1 Press SETUP6 Press SETUP to exit 4 Select “DELETE” using K / L, then press OK5 Press OK again to add the channel to the channel map OperationAdjusting Antenna 2 Press SETUP 3 Select “CHANNEL” using K / L, then press OK4 Select “ANTENNA” using K / L, then press OK 1 Press SETUP 2 Select “DETAIL” using K / L, then press OKSetting the Time Zone and D.S.T Daylight Saving Time 1 Press SETUP 2 Select “TIME” using K / L , then press OK3 Select “TIME ZONE” using K / L , then press OK 4 Select your time zone using K / L , then press OK3 Select “D.S.T” using K / L , then press OK 4 Select “ON” or “OFF” using s / B , then press OK1 Press SETUP 2 Select “DETAIL” using K / L , then press OK 3 Select “V-CHIP” using K / L , then press OK5 Select the desired rating type using K / L , then press OK 6 Select the desired rating usingK / L , then press OK repeatedly to switch between view and block MPAA Rating7 Press SETUP to exit 4 Enter 4737 in the password entry field5 Select “NEW PASSWORD” using K / L , then press OK 6 Enter the new 4-digit password using the Number buttons5 Select “MANUAL” using K / L , then press OK 3 Select “CLOSED CAPTION” using K / L , then press OK4 Select the desired closed caption item using K / L , then press OK 5 Select the desired DTV closed caption using K / L , then press OK3 Select “AUTO POWER DOWN” using K / L , then press OK Auto Power Down4 Select desired amount of time using K / L , then press OK You can view analog TV by switching “RF OUT” setting You cannot view Digital TV with this settingYou cannot view Analog TV with this setting Viewing Analog TVYou can view analog TV without switching “RF OUT” setting Method 2 Método2 Select “RF THROUGH” in “RF OUT” 3 Select the desired channel on your TVSetting RF OUT Using SETUP to Switch “RF OUT” Setting2 Select “CHANNEL” using K / L, then press OK 3 Select “RF OUT” using K / L, then press OKTroubleshooting No powerto the remote control Low volumeSpecifications Connecting Jacks ANT. IN/OUTPower Source Power ConsumptionLIMITED WARRANTY WARRANTY STATEMENT REGARDING NON AUTHORIZED REPAIRSFUNAI SERVICE CORPORATION Customer Service