BenQ SH960 user manual Shifting the projection lens, To use the lens shift lever

Page 16

English

Shifting the projection lens

The lens shift control provides flexibility for installing your projector. It allows the projector to be positioned off the center of the screen.

The lens shift is expressed as a percentage of the projected image height or width. It is measured as an offset from the projected image’s vertical or horizontal center. You can use the lever to shift the projection lens in any direction within the allowable range depending on your desired image position.

To use the lens shift lever:

1.Release the lever by turning it counterclockwise.

2.Move the lever to adjust the projected image position.

3.Lock the lever by turning it clockwise.

• When the screen position is fixed
Projector
	Range of
Screen	placement
	Center of lens
• When the projector position is fixed
100%
25%
-25%
-100%
41.3%	41.3%

• Please do not over-tighten the lever.

•Lens shift adjustment will not result in a degraded picture quality. In the unlikely event that the image distortion is produced, see "Adjusting the projected image" on page 25 for details.

16 Positioning your projector

Image 16

Contents Welcome Table of contents Important safety instructions Do not cover the projector with any item Avoid volatile liquids Moisture condensationDisposal Shipping contents OverviewRemote control operation Remote control batteriesCeiling mounting the projector Projector features Rear view Front and upper side viewUnder view Controls and functions Control panelMute Remote controlOperating the Laser pointer Choosing a location Floor FrontCeiling Front Floor RearObtaining a preferred projected image size Projection dimensions Installation for a 169 ratio screenInstallation for a 43 ratio screen HighestLens Height HShifting the projection lens To use the lens shift leverConnecting Hdmi devices PreparationsTerminal appearance Reference Picture quality ComponentConnecting component-video devices Connecting S-Video or video devicesConnecting a monitor Connecting a computerConnect the projector to a computer with a VGA cable Turning the projector on PreparationsSelecting an input source Using the OSD menuChanging Color Space Using the menus Using a security cable lockUse / to highlight the System Setup menu Press MENU/EXIT twice* to leave and save the settingsUtilizing the password function Setting a passwordIf you forget the password To leave the OSD menu, press MENU/EXITEntering the password recall procedure Changing the passwordDisabling the password function Write down the number and turn off your projectorAdjusting the projected image Adjusting the projection angleAuto-adjusting the image Fine-tuning the image size and clarityCorrecting picture distortion Ii. See step iv below for further operationTwo parallel sides No parallel sidesUsing the preset and user modes Selecting a preset modeFine-tuning the selected picture mode To select a picture mode that suits your needSetting the User 1/User 2 mode Resetting the picture modeTo reset the picture mode to the preset factory values Renaming user modesFine-tuning the picture quality Setting Black Level Selecting a color temperatureAdvanced picture quality controls Controlling image claritySetting a preferred color temperature Selecting a Gamma settingAdjusting Brilliant Color To set a preferred color temperatureSetting Film Mode To adjust and store the settingsTo leave and save the settings, press MENU/EXIT Color ManagementSelecting the aspect ratio Setting 3D Comb FilterAbout the aspect ratio Using Panamorph lenses optional Image Using the entire resolutionAspect ratio Aspect ratio image 169 displayUtilizing FAQ function Hiding the imageFreezing the image Press EnterAdjusting the sound Setting the lamp modeAdjusting the sound level Turning off the Power On/Off Ring ToneConfiguring the Lan Control Settings Controlling the projector through a Lan environmentIf you are in a Dhcp environment If you are in a non-DHCP environmentIi To switch input source, click on your desired signal Controlling the projector remotely through a web browserAuto Source Menu itemCategory Item Input Length Maximum Number To activate High Altitude Mode Operating in a high altitude environmentDisplaying more than one image source simultaneously To display the PIP windowHighlight PIP and press / to select On PIP function is effective at below source combinationsPOWER/ON II again Turning the projector offOn-Screen Display OSD structure On-Screen Display OSD menusMain menu Sub-menu Options System Setup DisplaySetup InformationPicture -- Advanced menu Picture -- Basic menuFunction Description Display menu System Setup menu Advanced Setup menu Information menu Cleaning the lens Cleaning the projector caseCare of the projector Storing the projectorSetting Lamp Mode as Dual-Reliable Setting Auto Power OffLamp information Getting to know the lamp hourReplacing the lamp Timing of replacing the lampStatus Message English Resetting the lamp timer Reset Lamp Timer? Power events IndicatorsLight Status & Description Troubleshooting Problem Cause RemedySpecifications OpticalElectrical TerminalsCeiling mount installation DimensionsMm x 354.7 mm x 167 mm W x D x H Timing chart Format Resolution Refresh rate FrequencySupported timing for PC input KHz MHzFormat Resolution Refresh rate Hz Freq. KHz Pixel Freq. MHz Format Resolution Refresh rate Freq. KHz Pixel Freq MHzSupported timing for Hdmi Hdcp input Supported timing for Edtv and Hdtv via Component inputsCopyright WarrantyDisclaimer