BenQ SH960 user manual Indicators, Light Status & Description, Power events

Page 57

Indicators


		Light				Status & Description
POWER		TEMP	LAMP1	LAMP2
					Power events
Orange		Off	Off	Off		Stand-by mode.
Green		Off	Off	Off		Powering up.
Flashing		Off	Off	Off		Powering up.
Flashing
Green		Off	Off	Off		Normal operation.
						1. The projector needs 90 seconds to cool down as it
Orange						was abnormally shut down without the normal
Orange		Off	Off	Off		cooling down process. Or
Flashing		Off	Off	Off		cooling down process. Or
Flashing						2. The projector needs to cool for 90 seconds after the
						2. The projector needs to cool for 90 seconds after the
						power is turned off.
Orange		Off	Off	Off		The projector has shutdown automatically. If you try to re-
Flashing		Off	Off	Off
Flashing
Orange		Off	Red	Off		start the projector, it will shutdown again. Please contact
Flashing		Off	Red	Off		your dealer for assistance.
Flashing						your dealer for assistance.
Red		Off	Red	Off
Lamp events
Off		Off	Red	Off		Lamp 1 failed. The projector has entered Single-Alternative
Off		Off	Red	Off		mode automatically. Replace lamp 1 as soon as possible.
						mode automatically. Replace lamp 1 as soon as possible.
Off		Off	Off	Red		Lamp 2 failed. The projector has entered Single-Alternative
Off		Off	Off	Red		mode automatically. Replace lamp 2 as soon as possible.
						mode automatically. Replace lamp 2 as soon as possible.
Off		Off	Red	Red		The projector has shutdown automatically. If you try to re-
Orange		Off	Red	Off		start the projector, it will shutdown again. Please contact
Orange		Off	Red	Off		your dealer for assistance.
						your dealer for assistance.
Thermal events

English

Off	Red	Off	Off
Off	Red	Red	Off
Off	Red	Green	Off
Off	Red	Orange	Off
Off	Red	Off	Red
Off	Red	Off	Green
Off	Red	Off	Orange
Orange	Red	Red	Off
Orange	Red	Green	Off
Orange	Red	Orange	Off
Off	Orange	Red	Off

The projector has shutdown automatically. If you try to re- start the projector, it will shutdown again. Please contact your dealer for assistance.

Additional information

57

Image 57

Contents Welcome Table of contents Important safety instructions Do not cover the projector with any item Moisture condensation Avoid volatile liquidsDisposal Overview Shipping contentsRemote control batteries Remote control operationCeiling mounting the projector Projector features Front and upper side view Rear viewUnder view Control panel Controls and functionsRemote control MuteOperating the Laser pointer Floor Front Choosing a locationCeiling Front Floor RearObtaining a preferred projected image size Installation for a 169 ratio screen Projection dimensionsHighest Installation for a 43 ratio screenLens Height HTo use the lens shift lever Shifting the projection lensPreparations Connecting Hdmi devicesTerminal appearance Reference Picture quality ComponentConnecting S-Video or video devices Connecting component-video devicesConnecting a computer Connecting a monitorConnect the projector to a computer with a VGA cable Preparations Turning the projector onUsing the OSD menu Selecting an input sourceChanging Color Space Using a security cable lock Using the menusUse / to highlight the System Setup menu Press MENU/EXIT twice* to leave and save the settingsSetting a password Utilizing the password functionIf you forget the password To leave the OSD menu, press MENU/EXITChanging the password Entering the password recall procedureDisabling the password function Write down the number and turn off your projectorAdjusting the projection angle Adjusting the projected imageAuto-adjusting the image Fine-tuning the image size and clarityIi. See step iv below for further operation Correcting picture distortionTwo parallel sides No parallel sidesSelecting a preset mode Using the preset and user modesFine-tuning the selected picture mode To select a picture mode that suits your needResetting the picture mode Setting the User 1/User 2 modeTo reset the picture mode to the preset factory values Renaming user modesFine-tuning the picture quality Selecting a color temperature Setting Black LevelAdvanced picture quality controls Controlling image claritySelecting a Gamma setting Setting a preferred color temperatureAdjusting Brilliant Color To set a preferred color temperatureTo adjust and store the settings Setting Film ModeTo leave and save the settings, press MENU/EXIT Color ManagementSetting 3D Comb Filter Selecting the aspect ratioAbout the aspect ratio Image Using the entire resolution Using Panamorph lenses optionalAspect ratio Aspect ratio image 169 displayHiding the image Utilizing FAQ functionFreezing the image Press EnterSetting the lamp mode Adjusting the soundAdjusting the sound level Turning off the Power On/Off Ring ToneControlling the projector through a Lan environment Configuring the Lan Control SettingsIf you are in a Dhcp environment If you are in a non-DHCP environmentControlling the projector remotely through a web browser Ii To switch input source, click on your desired signalAuto Source Menu itemCategory Item Input Length Maximum Number Operating in a high altitude environment To activate High Altitude ModeTo display the PIP window Displaying more than one image source simultaneouslyHighlight PIP and press / to select On PIP function is effective at below source combinationsTurning the projector off POWER/ON II againOn-Screen Display OSD menus On-Screen Display OSD structureMain menu Sub-menu Options Display System SetupInformation SetupPicture -- Basic menu Picture -- Advanced menuFunction Description Display menu System Setup menu Advanced Setup menu Information menu Cleaning the projector case Cleaning the lensCare of the projector Storing the projectorSetting Auto Power Off Setting Lamp Mode as Dual-ReliableLamp information Getting to know the lamp hourTiming of replacing the lamp Replacing the lampStatus Message English Resetting the lamp timer Reset Lamp Timer? Indicators Power eventsLight Status & Description Problem Cause Remedy TroubleshootingOptical SpecificationsElectrical TerminalsDimensions Ceiling mount installationMm x 354.7 mm x 167 mm W x D x H Format Resolution Refresh rate Frequency Timing chartSupported timing for PC input KHz MHzFormat Resolution Refresh rate Freq. KHz Pixel Freq MHz Format Resolution Refresh rate Hz Freq. KHz Pixel Freq. MHzSupported timing for Hdmi Hdcp input Supported timing for Edtv and Hdtv via Component inputsWarranty CopyrightDisclaimer