BenQ SH960 user manual Entering the password recall procedure, Changing the password

Page 24

English

Entering the password recall procedure

1.Make sure the Input Password page is displayed on screen. Press MODE. The projector will display a coded number on the screen.

2.Write down the number and turn off your projector.

3.Seek help from the local BenQ service center to decode the number. You may be required to provide proof of purchase documentation to verify that you are an authorized user of the projector.

Changing the password

Recall Password

Please write down the recall code, and contact your nearest BenQ Customer Center.

Recall code:

0 2 1 2

EXIT Back

1.Press MENU/EXIT and then press / until the Advanced Setup menu is highlighted.

2.Press / to highlight Password and press ENTER. The Password page is displayed.

3.Highlight Change Password and press ENTER. The Input Current Password page is displayed.

4.Enter the old password.

•If the password is correct, the message "Input New Password" is displayed.

•If the password is incorrect, the password error message is displayed lasting for three seconds, and the message "Input Current Password" is displayed for your retry. You can press MENU/EXIT to cancel the change or try another password.

5.Enter a new password.

IMPORTANT: The digits being input will be displayed as asterisks on-screen. Write your selected password down here in this manual in advance or right after the password is entered so that it is available to you should you ever forget it.

Password: __ __ __ __ __ __

Keep this manual in a safe place.

6.Confirm the new password by re-entering the new password.

7.You have successfully assigned a new password to the projector. Remember to enter the new password next time the projector is started.

8.To leave the OSD menu, press MENU/EXIT.

Disabling the password function

To disable password protection, go back to the Advanced Setup > Password > Password menu. Highlight Password and select Off by pressing / . The message "Input Password" is displayed. Enter the current password.

•If the password is correct, the OSD menu returns to the Password page with "Off" shown in the row of Password. You will not have to enter the password next time when turning on the projector.

•If the password is incorrect, the password error message is displayed lasting for three seconds, and the message "Input Password" is displayed for your retry. You can press MENU/EXIT to cancel the change or try another password.

Note that though the password function is disabled, you need to keep the old password in hand should you ever need to re-activate the password function by entering the old password.

Password

Password

Off

Change Password

EXIT Back

24 Using the projector

Page 23 Page 25
Image 24
Page 23 Page 25
Contents Welcome Table of contents Important safety instructions Do not cover the projector with any item Moisture condensation Avoid volatile liquidsDisposal Shipping contents OverviewRemote control batteries Remote control operationCeiling mounting the projector Projector features Front and upper side view Rear viewUnder view Controls and functions Control panelRemote control MuteOperating the Laser pointer Choosing a location Floor FrontCeiling Front Floor RearObtaining a preferred projected image size Projection dimensions Installation for a 169 ratio screenInstallation for a 43 ratio screen HighestLens Height HShifting the projection lens To use the lens shift leverConnecting Hdmi devices PreparationsTerminal appearance Reference Picture quality ComponentConnecting component-video devices Connecting S-Video or video devicesConnecting a computer Connecting a monitorConnect the projector to a computer with a VGA cable Turning the projector on PreparationsUsing the OSD menu Selecting an input sourceChanging Color Space Using the menus Using a security cable lockUse / to highlight the System Setup menu Press MENU/EXIT twice* to leave and save the settingsUtilizing the password function Setting a passwordIf you forget the password To leave the OSD menu, press MENU/EXITEntering the password recall procedure Changing the passwordDisabling the password function Write down the number and turn off your projectorAdjusting the projected image Adjusting the projection angleAuto-adjusting the image Fine-tuning the image size and clarityCorrecting picture distortion Ii. See step iv below for further operationTwo parallel sides No parallel sidesUsing the preset and user modes Selecting a preset modeFine-tuning the selected picture mode To select a picture mode that suits your needSetting the User 1/User 2 mode Resetting the picture modeTo reset the picture mode to the preset factory values Renaming user modesFine-tuning the picture quality Setting Black Level Selecting a color temperatureAdvanced picture quality controls Controlling image claritySetting a preferred color temperature Selecting a Gamma settingAdjusting Brilliant Color To set a preferred color temperatureSetting Film Mode To adjust and store the settingsTo leave and save the settings, press MENU/EXIT Color ManagementSetting 3D Comb Filter Selecting the aspect ratioAbout the aspect ratio Using Panamorph lenses optional Image Using the entire resolutionAspect ratio Aspect ratio image 169 displayUtilizing FAQ function Hiding the imageFreezing the image Press EnterAdjusting the sound Setting the lamp modeAdjusting the sound level Turning off the Power On/Off Ring ToneConfiguring the Lan Control Settings Controlling the projector through a Lan environmentIf you are in a Dhcp environment If you are in a non-DHCP environmentIi To switch input source, click on your desired signal Controlling the projector remotely through a web browserAuto Source Menu itemCategory Item Input Length Maximum Number To activate High Altitude Mode Operating in a high altitude environmentDisplaying more than one image source simultaneously To display the PIP windowHighlight PIP and press / to select On PIP function is effective at below source combinationsPOWER/ON II again Turning the projector offOn-Screen Display OSD menus On-Screen Display OSD structureMain menu Sub-menu Options System Setup DisplaySetup InformationPicture -- Basic menu Picture -- Advanced menuFunction Description Display menu System Setup menu Advanced Setup menu Information menu Cleaning the lens Cleaning the projector caseCare of the projector Storing the projectorSetting Lamp Mode as Dual-Reliable Setting Auto Power OffLamp information Getting to know the lamp hourTiming of replacing the lamp Replacing the lampStatus Message English Resetting the lamp timer Reset Lamp Timer? Indicators Power eventsLight Status & Description Troubleshooting Problem Cause RemedySpecifications OpticalElectrical TerminalsDimensions Ceiling mount installationMm x 354.7 mm x 167 mm W x D x H Timing chart Format Resolution Refresh rate FrequencySupported timing for PC input KHz MHzFormat Resolution Refresh rate Hz Freq. KHz Pixel Freq. MHz Format Resolution Refresh rate Freq. KHz Pixel Freq MHzSupported timing for Hdmi Hdcp input Supported timing for Edtv and Hdtv via Component inputsWarranty CopyrightDisclaimer
Top Page Image Contents