BenQ SH960 user manual Specifications, Optical, Electrical, Terminals

Page 59

Specifications

All specifications are subject to change without notice.

Optical

Projection system

Single-chip DLP™ system.

DMD chip

0.65" DLP (1920 x 1080)

Lens

F = 2.48 to 2.81, f = 24.1 to 36.15 mm

Projection screen size

28" to 300"

Lamp

330W

 

 

Electrical

PC: 640 x 480 to 1920 x 1200

 

 

 

 

Compatibility

 

 

 

Video: NTSC, PAL, SECAM, YPbPr (480i/480p/576i/576p/720p/

 

 

 

1080i/1080p), HDTV (720p/1080i/1080p)

Color Space

Typ. = 60% NTSC (Target Color Gamut = HDTV Rec. 709)

 

 

Terminals

Analog RGB: D-Sub 15-pin (female) x 1

 

 

 

 

Input

 

 

 

HDMI (V. 1.3) x 1

 

 

 

Component Video (Y/CB/CR, Y/PB/PR) x 1

 

 

 

Component Video (Y/CB/CR, Y/PB/PR) x 1 (shared with RGB input)

 

 

 

Composite Video x 1

 

 

 

S-Video x 1

 

 

 

Audio in x 1

Output

12VDC (Max. 0.5 A)

 

 

 

Analog RGB: D-Sub 15-pin (female) x 1

 

 

 

Audio out x 1

 

 

 

Speaker: 5W x 2

Control

Serial Connector: RS232 9 pin (male)

 

 

 

Mini B type USB x 1

 

 

 

IR receiver x 2

 

 

 

LAN x 1

 

 

General characteristics

 

 

 

 

 

 

 

Projector weight

< 11 kg (24.3 lbs)

Power

VAC 100-240V, 10 A, 50-60Hz

Power consumption

Max. 940 W; Standby < 1 W

Operating temperature

0 °C to 40 °C (without condensation)

Operating humidity

10% - 90% (without condensation)

Operating altitude

0-1499 m at 0°C-35°C

 

 

 

1500-3000 m at 0°C-30°C (with High Altitude Mode on)

Storage temperature

-20°C- 60°C/-4°F to 140°F

Storage humidity

10% - 90%

English

Additional information

59

Image 59
Contents Welcome Table of contents Important safety instructions Do not cover the projector with any item Disposal Moisture condensationAvoid volatile liquids Overview Shipping contentsCeiling mounting the projector Remote control batteriesRemote control operation Projector features Under view Front and upper side viewRear view Control panel Controls and functionsOperating the Laser pointer Remote controlMute Floor Rear Choosing a locationFloor Front Ceiling FrontObtaining a preferred projected image size Installation for a 169 ratio screen Projection dimensionsHeight H Installation for a 43 ratio screenHighest LensTo use the lens shift lever Shifting the projection lensComponent Connecting Hdmi devicesPreparations Terminal appearance Reference Picture qualityConnecting S-Video or video devices Connecting component-video devicesConnect the projector to a computer with a VGA cable Connecting a computerConnecting a monitor Preparations Turning the projector onChanging Color Space Using the OSD menuSelecting an input source Press MENU/EXIT twice* to leave and save the settings Using the menusUsing a security cable lock Use / to highlight the System Setup menuTo leave the OSD menu, press MENU/EXIT Utilizing the password functionSetting a password If you forget the passwordWrite down the number and turn off your projector Entering the password recall procedureChanging the password Disabling the password functionFine-tuning the image size and clarity Adjusting the projected imageAdjusting the projection angle Auto-adjusting the imageNo parallel sides Correcting picture distortionIi. See step iv below for further operation Two parallel sidesTo select a picture mode that suits your need Using the preset and user modesSelecting a preset mode Fine-tuning the selected picture modeRenaming user modes Setting the User 1/User 2 modeResetting the picture mode To reset the picture mode to the preset factory valuesFine-tuning the picture quality Controlling image clarity Setting Black LevelSelecting a color temperature Advanced picture quality controlsTo set a preferred color temperature Setting a preferred color temperatureSelecting a Gamma setting Adjusting Brilliant ColorColor Management Setting Film ModeTo adjust and store the settings To leave and save the settings, press MENU/EXITAbout the aspect ratio Setting 3D Comb FilterSelecting the aspect ratio 169 display Using Panamorph lenses optionalImage Using the entire resolution Aspect ratio Aspect ratio imagePress Enter Utilizing FAQ functionHiding the image Freezing the imageTurning off the Power On/Off Ring Tone Adjusting the soundSetting the lamp mode Adjusting the sound levelIf you are in a non-DHCP environment Configuring the Lan Control SettingsControlling the projector through a Lan environment If you are in a Dhcp environmentMenu item Ii To switch input source, click on your desired signalControlling the projector remotely through a web browser Auto SourceCategory Item Input Length Maximum Number Operating in a high altitude environment To activate High Altitude ModePIP function is effective at below source combinations Displaying more than one image source simultaneouslyTo display the PIP window Highlight PIP and press / to select OnTurning the projector off POWER/ON II againMain menu Sub-menu Options On-Screen Display OSD menusOn-Screen Display OSD structure Display System SetupInformation SetupFunction Description Picture -- Basic menuPicture -- Advanced menu Display menu System Setup menu Advanced Setup menu Information menu Storing the projector Cleaning the lensCleaning the projector case Care of the projectorGetting to know the lamp hour Setting Lamp Mode as Dual-ReliableSetting Auto Power Off Lamp informationStatus Message Timing of replacing the lampReplacing the lamp English Resetting the lamp timer Reset Lamp Timer? Light Status & Description IndicatorsPower events Problem Cause Remedy TroubleshootingTerminals SpecificationsOptical ElectricalMm x 354.7 mm x 167 mm W x D x H DimensionsCeiling mount installation KHz MHz Timing chartFormat Resolution Refresh rate Frequency Supported timing for PC inputSupported timing for Edtv and Hdtv via Component inputs Format Resolution Refresh rate Hz Freq. KHz Pixel Freq. MHzFormat Resolution Refresh rate Freq. KHz Pixel Freq MHz Supported timing for Hdmi Hdcp inputDisclaimer WarrantyCopyright