BenQ SH960 user manual Correcting picture distortion, Ii. See step iv below for further operation

Page 26

English

Correcting picture distortion

Keystoning occurs when the projector is not perpendicular to the screen and is where the projected picture displays visible as a trapezoid shape like either of the following:

•Two parallel sides (left and right, or top and bottom) but is noticeably wider on either side.

•No parallel sides.

To correct the picture’s shape, you can perform the following steps.

1.Adjust the projection angle. Move the projector to be in front of the center of the screen with the center of the lens level with the screen.

2.If the picture is stilled distorted, or the projector is unable to be positioned as described above, you will need to manually correct the picture.

•Using the remote control or projector

i. Press one of the Arrow/Keystone keys (Left / , Up / , Right / , Down / ) to display the Keystone page.

ii. See step iv below for further operation.

• Using the OSD menu

i. Press MENU/EXIT and then press / until the Display menu is highlighted.

ii.Press to highlight Keystone and press ENTER. The Keystone page is displayed.

iii.Highlight 2D Keystone and press ENTER. The keystone correction page is displayed.

iv.Press the key whose keystone icon is opposite to the shape of the projected picture. Continue pressing the same key or press the other keys until you are satisfied with the shape.

The values on the lower portion of the page change while pressing. When the values reach their maximum or minimum with repeated key presses, the picture’s shape will stop changing. You will not be able to change the picture further in that direction.

Display

Aspect Ratio	Anamorphic
Keystone	ENTER
Position
Overscan Adjustment	0
Color Space Conversion	RGB
PIP
PC & Component YPbPr Tuning
Blank Timer	Disable
Test Pattern
S-Video	EXIT Back
Keystone
2D Keystone	ENTER

Two parallel sides			EXIT	Back
			EXIT	Back
Press	Press	Keystone
/ .	/ .
No parallel sides
Press	Press
/ .	/ .		EXIT Back
		1	0

26 Using the projector

Image 26

Contents Welcome Table of contents Important safety instructions Do not cover the projector with any item Disposal Moisture condensationAvoid volatile liquids Shipping contents OverviewCeiling mounting the projector Remote control batteriesRemote control operation Projector features Under view Front and upper side viewRear view Controls and functions Control panelOperating the Laser pointer Remote controlMute Ceiling Front Choosing a locationFloor Front Floor RearObtaining a preferred projected image size Projection dimensions Installation for a 169 ratio screenLens Installation for a 43 ratio screenHighest Height HShifting the projection lens To use the lens shift leverTerminal appearance Reference Picture quality Connecting Hdmi devicesPreparations ComponentConnecting component-video devices Connecting S-Video or video devicesConnect the projector to a computer with a VGA cable Connecting a computerConnecting a monitor Turning the projector on PreparationsChanging Color Space Using the OSD menuSelecting an input source Use / to highlight the System Setup menu Using the menusUsing a security cable lock Press MENU/EXIT twice* to leave and save the settingsIf you forget the password Utilizing the password functionSetting a password To leave the OSD menu, press MENU/EXITDisabling the password function Entering the password recall procedureChanging the password Write down the number and turn off your projectorAuto-adjusting the image Adjusting the projected imageAdjusting the projection angle Fine-tuning the image size and clarityTwo parallel sides Correcting picture distortionIi. See step iv below for further operation No parallel sidesFine-tuning the selected picture mode Using the preset and user modesSelecting a preset mode To select a picture mode that suits your needTo reset the picture mode to the preset factory values Setting the User 1/User 2 modeResetting the picture mode Renaming user modesFine-tuning the picture quality Advanced picture quality controls Setting Black LevelSelecting a color temperature Controlling image clarityAdjusting Brilliant Color Setting a preferred color temperatureSelecting a Gamma setting To set a preferred color temperatureTo leave and save the settings, press MENU/EXIT Setting Film ModeTo adjust and store the settings Color ManagementAbout the aspect ratio Setting 3D Comb FilterSelecting the aspect ratio Aspect ratio Aspect ratio image Using Panamorph lenses optionalImage Using the entire resolution 169 displayFreezing the image Utilizing FAQ functionHiding the image Press EnterAdjusting the sound level Adjusting the soundSetting the lamp mode Turning off the Power On/Off Ring ToneIf you are in a Dhcp environment Configuring the Lan Control SettingsControlling the projector through a Lan environment If you are in a non-DHCP environmentAuto Source Ii To switch input source, click on your desired signalControlling the projector remotely through a web browser Menu itemCategory Item Input Length Maximum Number To activate High Altitude Mode Operating in a high altitude environmentHighlight PIP and press / to select On Displaying more than one image source simultaneouslyTo display the PIP window PIP function is effective at below source combinationsPOWER/ON II again Turning the projector offMain menu Sub-menu Options On-Screen Display OSD menusOn-Screen Display OSD structure System Setup DisplaySetup InformationFunction Description Picture -- Basic menuPicture -- Advanced menu Display menu System Setup menu Advanced Setup menu Information menu Care of the projector Cleaning the lensCleaning the projector case Storing the projectorLamp information Setting Lamp Mode as Dual-ReliableSetting Auto Power Off Getting to know the lamp hourStatus Message Timing of replacing the lampReplacing the lamp English Resetting the lamp timer Reset Lamp Timer? Light Status & Description IndicatorsPower events Troubleshooting Problem Cause RemedyElectrical SpecificationsOptical TerminalsMm x 354.7 mm x 167 mm W x D x H DimensionsCeiling mount installation Supported timing for PC input Timing chartFormat Resolution Refresh rate Frequency KHz MHzSupported timing for Hdmi Hdcp input Format Resolution Refresh rate Hz Freq. KHz Pixel Freq. MHzFormat Resolution Refresh rate Freq. KHz Pixel Freq MHz Supported timing for Edtv and Hdtv via Component inputsDisclaimer WarrantyCopyright