BenQ SH960 Setting the User 1/User 2 mode, Renaming user modes, Resetting the picture mode

Page 28

English

Setting the User 1/User 2 mode

There are two user-definable modes if the current available picture modes are not suitable for your need. You can use one of the picture modes (except the selected User mode) as a starting point and customize the settings.

1.In the Picture -- Basic menu, highlight Picture Mode and press /

to select User 1 or User 2 mode.

2.Press to highlight Load Settings From.

This function is only available when User 1 or User 2 mode is selected up in the Picture Mode sub-menu item.

3.Press ENTER to display the Load Settings From page.

4.Press to highlight a picture mode that is closest to your need and press ENTER.

5.Press to select a sub-menu item to be changed and adjust the value with / . See "Fine-tuning the picture quality" on page 29 and "Advanced picture quality controls" on page 30 for details.

6.When all settings have been done, press MENU/EXIT to save and leave the settings.

Picture -- Basic

Picture Mode

User 1

 

Load Settings From

ENTER

 

Brightness

+50

 

Contrast

+50

 

Color

+50

 

Tint

0

 

Sharpness

+ 3

 

Reset Picture Settings

 

 

Rename User Mode

 

 

S-Video

EXIT

Back

Load Settings From

 

 

Expert Mode 1

 

 

Expert Mode 2

 

 

Cinema

ENTER

 

Dynamic

 

 

Presentation

 

 

sRGB

 

 

User 1

 

 

User 2

 

 

 

EXIT

Back

Renaming user modes

You can change User 1 and User 2 to the names easy to be identified or understood by the users of this projector. The new name can be up to 12 characters including English letters (A-Z, a-z), digits (0-9), and space (_).

To rename user modes:

1.In the Picture -- Basic menu, highlight Rename User Mode and press ENTER to display the Rename User Mode page.

2.Press / to highlight the item you want to rename and press ENTER. The first letter will be highlighted by a white box.

3.Press / to select the first character.

4.Press to move along until the new name is set and press ENTER to confirm.

5.Repeat steps 2-4if you want to change the other names.

Resetting the picture mode

All of the adjustments you’ve done in the Picture -- Basic and Picture -- Advanced menus can be returned to the factory preset values with a key press on the highlight of Reset.

To reset the picture mode to the preset factory values:

1.In the Picture -- Basic menu, highlight Picture Mode and press / to select the picture mode (including User 1 or User 2) you want to reset.

2.Press to highlight Reset Picture Settings and press ENTER. The confirmation message is displayed.

3.Press / to highlight Reset and press ENTER. The picture mode will return to the factory preset settings.

4.Repeat steps 1-3if you want to reset other picture modes.

• The following settings will still remain: Color Temperature, Color Temperature User_ Fine Tuning, Gamma Selection, Film Mode, 3D Comb Filter.

•Do not to be confused with the Reset Picture Settings function here with the Reset All Settings in the Advanced Setup menu. The Reset All Settings function returns most of the settings to the factory preset values system wide. See "Reset All Settings" on page 49 for details.

28 Using the projector

Page 27 Page 29
Image 28
Page 27 Page 29
Contents Welcome Table of contents Important safety instructions Do not cover the projector with any item Avoid volatile liquids Moisture condensationDisposal Shipping contents OverviewRemote control operation Remote control batteriesCeiling mounting the projector Projector features Rear view Front and upper side viewUnder view Controls and functions Control panelMute Remote controlOperating the Laser pointer Choosing a location Floor FrontCeiling Front Floor RearObtaining a preferred projected image size Projection dimensions Installation for a 169 ratio screenInstallation for a 43 ratio screen HighestLens Height HShifting the projection lens To use the lens shift leverConnecting Hdmi devices PreparationsTerminal appearance Reference Picture quality ComponentConnecting component-video devices Connecting S-Video or video devicesConnecting a monitor Connecting a computerConnect the projector to a computer with a VGA cable Turning the projector on PreparationsSelecting an input source Using the OSD menuChanging Color Space Using the menus Using a security cable lockUse / to highlight the System Setup menu Press MENU/EXIT twice* to leave and save the settingsUtilizing the password function Setting a passwordIf you forget the password To leave the OSD menu, press MENU/EXITEntering the password recall procedure Changing the passwordDisabling the password function Write down the number and turn off your projectorAdjusting the projected image Adjusting the projection angleAuto-adjusting the image Fine-tuning the image size and clarityCorrecting picture distortion Ii. See step iv below for further operationTwo parallel sides No parallel sidesUsing the preset and user modes Selecting a preset modeFine-tuning the selected picture mode To select a picture mode that suits your needSetting the User 1/User 2 mode Resetting the picture modeTo reset the picture mode to the preset factory values Renaming user modesFine-tuning the picture quality Setting Black Level Selecting a color temperatureAdvanced picture quality controls Controlling image claritySetting a preferred color temperature Selecting a Gamma settingAdjusting Brilliant Color To set a preferred color temperatureSetting Film Mode To adjust and store the settingsTo leave and save the settings, press MENU/EXIT Color ManagementSelecting the aspect ratio Setting 3D Comb FilterAbout the aspect ratio Using Panamorph lenses optional Image Using the entire resolutionAspect ratio Aspect ratio image 169 displayUtilizing FAQ function Hiding the imageFreezing the image Press EnterAdjusting the sound Setting the lamp modeAdjusting the sound level Turning off the Power On/Off Ring ToneConfiguring the Lan Control Settings Controlling the projector through a Lan environmentIf you are in a Dhcp environment If you are in a non-DHCP environmentIi To switch input source, click on your desired signal Controlling the projector remotely through a web browserAuto Source Menu itemCategory Item Input Length Maximum Number To activate High Altitude Mode Operating in a high altitude environmentDisplaying more than one image source simultaneously To display the PIP windowHighlight PIP and press / to select On PIP function is effective at below source combinationsPOWER/ON II again Turning the projector offOn-Screen Display OSD structure On-Screen Display OSD menusMain menu Sub-menu Options System Setup DisplaySetup InformationPicture -- Advanced menu Picture -- Basic menuFunction Description Display menu System Setup menu Advanced Setup menu Information menu Cleaning the lens Cleaning the projector caseCare of the projector Storing the projectorSetting Lamp Mode as Dual-Reliable Setting Auto Power OffLamp information Getting to know the lamp hourReplacing the lamp Timing of replacing the lampStatus Message English Resetting the lamp timer Reset Lamp Timer? Power events IndicatorsLight Status & Description Troubleshooting Problem Cause RemedySpecifications OpticalElectrical TerminalsCeiling mount installation DimensionsMm x 354.7 mm x 167 mm W x D x H Timing chart Format Resolution Refresh rate FrequencySupported timing for PC input KHz MHzFormat Resolution Refresh rate Hz Freq. KHz Pixel Freq. MHz Format Resolution Refresh rate Freq. KHz Pixel Freq MHzSupported timing for Hdmi Hdcp input Supported timing for Edtv and Hdtv via Component inputsCopyright WarrantyDisclaimer
Top Page Image Contents