BenQ SH960 user manual Hiding the image, Freezing the image, Utilizing FAQ function, Press Enter

Page 35

Hiding the image

In order to draw the audience's full attention to the presenter, you can use

BLANK to hide the screen image. When this function is activated with an audio input connected, the audio can still be heard.

You can set the blank time in the Display > Blank Timer menu to let the projector return the image automatically after a period of time when there is no action taken on the blank screen. The length of time can be set from 5 to 30 minutes in 5-minute increments.

If the preset time spans are not suitable for your personation, select Disable.

No matter Blank Timer is activated or not, you can press any key on the projector or remote control to restore the picture.

Once BLANK is pressed, the projector lamp enters Dual-Reliable mode automatically.

Freezing the image

Press FREEZE on the remote control to freeze the image. The word

"FREEZE" will be displayed in the upper left corner of the screen. To release the function, press any key on the projector or remote control.

If your remote control has the following keys, please note that they cannot be pressed to release the function: LASER, #1, #4, PAGE UP/PAGE DOWN.

Even if an image is frozen on the screen, the pictures are running on the video or other device. If the connected devices have active audio output, you will still hear the audio even though the image is frozen onscreen.

Utilizing FAQ function

The Information menu contains possible solutions to problems regarding image quality, installation, special feature operation and service information.

To get the FAQ information:

1. Press or press MENU/EXIT to open the OSD menu and press

 

/ to highlight the Information menu.

2.

Press

to select FAQ-Image and Installation or FAQ-Features and

 

Service.

 

3.

Press ENTER.

4.

Press

/ to select a problem and press ENTER for possible

 

solutions.

5.

To leave and save the settings, press MENU/EXIT.

English

Using the projector

35

Image 35
Contents Welcome Table of contents Important safety instructions Do not cover the projector with any item Disposal Moisture condensationAvoid volatile liquids Overview Shipping contentsCeiling mounting the projector Remote control batteriesRemote control operation Projector features Under view Front and upper side viewRear view Control panel Controls and functionsOperating the Laser pointer Remote controlMute Floor Rear Choosing a locationFloor Front Ceiling FrontObtaining a preferred projected image size Installation for a 169 ratio screen Projection dimensionsHeight H Installation for a 43 ratio screenHighest LensTo use the lens shift lever Shifting the projection lensComponent Connecting Hdmi devicesPreparations Terminal appearance Reference Picture qualityConnecting S-Video or video devices Connecting component-video devicesConnect the projector to a computer with a VGA cable Connecting a computerConnecting a monitor Preparations Turning the projector onChanging Color Space Using the OSD menuSelecting an input source Press MENU/EXIT twice* to leave and save the settings Using the menusUsing a security cable lock Use / to highlight the System Setup menuTo leave the OSD menu, press MENU/EXIT Utilizing the password functionSetting a password If you forget the passwordWrite down the number and turn off your projector Entering the password recall procedureChanging the password Disabling the password functionFine-tuning the image size and clarity Adjusting the projected imageAdjusting the projection angle Auto-adjusting the imageNo parallel sides Correcting picture distortionIi. See step iv below for further operation Two parallel sidesTo select a picture mode that suits your need Using the preset and user modesSelecting a preset mode Fine-tuning the selected picture modeRenaming user modes Setting the User 1/User 2 modeResetting the picture mode To reset the picture mode to the preset factory valuesFine-tuning the picture quality Controlling image clarity Setting Black LevelSelecting a color temperature Advanced picture quality controlsTo set a preferred color temperature Setting a preferred color temperatureSelecting a Gamma setting Adjusting Brilliant ColorColor Management Setting Film ModeTo adjust and store the settings To leave and save the settings, press MENU/EXITAbout the aspect ratio Setting 3D Comb FilterSelecting the aspect ratio 169 display Using Panamorph lenses optionalImage Using the entire resolution Aspect ratio Aspect ratio imagePress Enter Utilizing FAQ functionHiding the image Freezing the imageTurning off the Power On/Off Ring Tone Adjusting the soundSetting the lamp mode Adjusting the sound levelIf you are in a non-DHCP environment Configuring the Lan Control SettingsControlling the projector through a Lan environment If you are in a Dhcp environmentMenu item Ii To switch input source, click on your desired signalControlling the projector remotely through a web browser Auto SourceCategory Item Input Length Maximum Number Operating in a high altitude environment To activate High Altitude ModePIP function is effective at below source combinations Displaying more than one image source simultaneouslyTo display the PIP window Highlight PIP and press / to select OnTurning the projector off POWER/ON II againMain menu Sub-menu Options On-Screen Display OSD menusOn-Screen Display OSD structure Display System SetupInformation SetupFunction Description Picture -- Basic menuPicture -- Advanced menu Display menu System Setup menu Advanced Setup menu Information menu Storing the projector Cleaning the lensCleaning the projector case Care of the projectorGetting to know the lamp hour Setting Lamp Mode as Dual-ReliableSetting Auto Power Off Lamp informationStatus Message Timing of replacing the lampReplacing the lamp English Resetting the lamp timer Reset Lamp Timer? Light Status & Description IndicatorsPower events Problem Cause Remedy TroubleshootingTerminals SpecificationsOptical ElectricalMm x 354.7 mm x 167 mm W x D x H DimensionsCeiling mount installation KHz MHz Timing chartFormat Resolution Refresh rate Frequency Supported timing for PC inputSupported timing for Edtv and Hdtv via Component inputs Format Resolution Refresh rate Hz Freq. KHz Pixel Freq. MHzFormat Resolution Refresh rate Freq. KHz Pixel Freq MHz Supported timing for Hdmi Hdcp inputDisclaimer WarrantyCopyright