BenQ SH960 user manual Reset Lamp Timer?

Page 56

English

1.After the start-up logo, press MENU/EXIT and then press / until the Advanced Setup menu is highlighted.

2.Press to highlight Lamp Settings and press ENTER. The Lamp Settings page is displayed.

3.Highlight Reset Lamp Timer 1/Reset Lamp Timer 2 and press ENTER. A warning message is displayed asking if you want to reset the lamp timer. Highlight Reset and press ENTER. The lamp time will be reset to "0".

Advanced Setup

Lamp Settings

ENTER

HDMI Settings

 

Baud Rate

115200

High Altitude Mode

Off

Audio Settings

 

Password

 

Lan Control Settings

 

Reset All Settings

 

Direct Power On

Off

Signal Power On

Off

Expert Mode

 

S-Video

EXIT Back

Lamp Settings

Lamp Mode

 

Reset Lamp Timer 1

ENTER

Reset Lamp Timer 2

 

Equivalent Lamp Hour #1

50 hours

Equivalent Lamp Hour #2

50 hours

 

EXIT Back

WARNING

Reset Lamp Timer?

Reset Cancel

56 Additional information

Image 56
Contents Welcome Table of contents Important safety instructions Do not cover the projector with any item Disposal Moisture condensationAvoid volatile liquids Shipping contents OverviewCeiling mounting the projector Remote control batteriesRemote control operation Projector features Under view Front and upper side viewRear view Controls and functions Control panelOperating the Laser pointer Remote controlMute Choosing a location Floor FrontCeiling Front Floor RearObtaining a preferred projected image size Projection dimensions Installation for a 169 ratio screenInstallation for a 43 ratio screen HighestLens Height HShifting the projection lens To use the lens shift leverConnecting Hdmi devices PreparationsTerminal appearance Reference Picture quality ComponentConnecting component-video devices Connecting S-Video or video devicesConnect the projector to a computer with a VGA cable Connecting a computerConnecting a monitor Turning the projector on PreparationsChanging Color Space Using the OSD menuSelecting an input source Using the menus Using a security cable lockUse / to highlight the System Setup menu Press MENU/EXIT twice* to leave and save the settingsUtilizing the password function Setting a passwordIf you forget the password To leave the OSD menu, press MENU/EXITEntering the password recall procedure Changing the passwordDisabling the password function Write down the number and turn off your projectorAdjusting the projected image Adjusting the projection angleAuto-adjusting the image Fine-tuning the image size and clarityCorrecting picture distortion Ii. See step iv below for further operationTwo parallel sides No parallel sidesUsing the preset and user modes Selecting a preset modeFine-tuning the selected picture mode To select a picture mode that suits your needSetting the User 1/User 2 mode Resetting the picture modeTo reset the picture mode to the preset factory values Renaming user modesFine-tuning the picture quality Setting Black Level Selecting a color temperatureAdvanced picture quality controls Controlling image claritySetting a preferred color temperature Selecting a Gamma settingAdjusting Brilliant Color To set a preferred color temperatureSetting Film Mode To adjust and store the settingsTo leave and save the settings, press MENU/EXIT Color ManagementAbout the aspect ratio Setting 3D Comb FilterSelecting the aspect ratio Using Panamorph lenses optional Image Using the entire resolutionAspect ratio Aspect ratio image 169 displayUtilizing FAQ function Hiding the imageFreezing the image Press EnterAdjusting the sound Setting the lamp modeAdjusting the sound level Turning off the Power On/Off Ring ToneConfiguring the Lan Control Settings Controlling the projector through a Lan environmentIf you are in a Dhcp environment If you are in a non-DHCP environmentIi To switch input source, click on your desired signal Controlling the projector remotely through a web browserAuto Source Menu itemCategory Item Input Length Maximum Number To activate High Altitude Mode Operating in a high altitude environmentDisplaying more than one image source simultaneously To display the PIP windowHighlight PIP and press / to select On PIP function is effective at below source combinationsPOWER/ON II again Turning the projector offMain menu Sub-menu Options On-Screen Display OSD menusOn-Screen Display OSD structure System Setup DisplaySetup InformationFunction Description Picture -- Basic menuPicture -- Advanced menu Display menu System Setup menu Advanced Setup menu Information menu Cleaning the lens Cleaning the projector caseCare of the projector Storing the projectorSetting Lamp Mode as Dual-Reliable Setting Auto Power OffLamp information Getting to know the lamp hourStatus Message Timing of replacing the lampReplacing the lamp English Resetting the lamp timer Reset Lamp Timer? Light Status & Description IndicatorsPower events Troubleshooting Problem Cause RemedySpecifications OpticalElectrical TerminalsMm x 354.7 mm x 167 mm W x D x H DimensionsCeiling mount installation Timing chart Format Resolution Refresh rate FrequencySupported timing for PC input KHz MHzFormat Resolution Refresh rate Hz Freq. KHz Pixel Freq. MHz Format Resolution Refresh rate Freq. KHz Pixel Freq MHzSupported timing for Hdmi Hdcp input Supported timing for Edtv and Hdtv via Component inputsDisclaimer WarrantyCopyright