BenQ SH960 user manual English

Page 54

English

1.Turn the power off and disconnect the projector from the power outlet. Turn off all connected equipment and disconnect all other cables. See "Turning the projector off" on page 42 for details.

2.Loosen the screw on the lamp cover.

3. Remove the lamp cover.

5.Loosen the screw that hold the lamp to the projector. Disconnect the lamp connector from the projector.

6.Lift the handle so that it is perpendicular to the lamp. Use the handle to slowly pull the lamp out of the projector.

4.Identify the lamp you want to replace by looking at the top of the lamp.

2 1

Notes

Pulling it too quickly may cause the lamp to break and scatter broken glass in the projector. To reduce the risk of injuries to fingers and damage to internal components, use caution when removing lamp glass that has shattered.

Do not place the lamp in locations where water might splash on it, children can reach it, near or above heat sources, or near flammable materials.

Do not insert your hand into the projector when the lamp is removed. If you touch the optical components inside, it could cause blurred images.

54 Additional information

Image 54
Contents Welcome Table of contents Important safety instructions Do not cover the projector with any item Moisture condensation Avoid volatile liquidsDisposal Shipping contents OverviewRemote control batteries Remote control operationCeiling mounting the projector Projector features Front and upper side view Rear viewUnder view Controls and functions Control panelRemote control MuteOperating the Laser pointer Ceiling Front Choosing a locationFloor Front Floor RearObtaining a preferred projected image size Projection dimensions Installation for a 169 ratio screenLens Installation for a 43 ratio screenHighest Height HShifting the projection lens To use the lens shift leverTerminal appearance Reference Picture quality Connecting Hdmi devicesPreparations ComponentConnecting component-video devices Connecting S-Video or video devicesConnecting a computer Connecting a monitorConnect the projector to a computer with a VGA cable Turning the projector on PreparationsUsing the OSD menu Selecting an input sourceChanging Color Space Use / to highlight the System Setup menu Using the menusUsing a security cable lock Press MENU/EXIT twice* to leave and save the settingsIf you forget the password Utilizing the password functionSetting a password To leave the OSD menu, press MENU/EXITDisabling the password function Entering the password recall procedureChanging the password Write down the number and turn off your projectorAuto-adjusting the image Adjusting the projected imageAdjusting the projection angle Fine-tuning the image size and clarityTwo parallel sides Correcting picture distortionIi. See step iv below for further operation No parallel sidesFine-tuning the selected picture mode Using the preset and user modesSelecting a preset mode To select a picture mode that suits your needTo reset the picture mode to the preset factory values Setting the User 1/User 2 modeResetting the picture mode Renaming user modesFine-tuning the picture quality Advanced picture quality controls Setting Black LevelSelecting a color temperature Controlling image clarityAdjusting Brilliant Color Setting a preferred color temperatureSelecting a Gamma setting To set a preferred color temperatureTo leave and save the settings, press MENU/EXIT Setting Film ModeTo adjust and store the settings Color ManagementSetting 3D Comb Filter Selecting the aspect ratioAbout the aspect ratio Aspect ratio Aspect ratio image Using Panamorph lenses optionalImage Using the entire resolution 169 displayFreezing the image Utilizing FAQ functionHiding the image Press EnterAdjusting the sound level Adjusting the soundSetting the lamp mode Turning off the Power On/Off Ring ToneIf you are in a Dhcp environment Configuring the Lan Control SettingsControlling the projector through a Lan environment If you are in a non-DHCP environmentAuto Source Ii To switch input source, click on your desired signalControlling the projector remotely through a web browser Menu itemCategory Item Input Length Maximum Number To activate High Altitude Mode Operating in a high altitude environmentHighlight PIP and press / to select On Displaying more than one image source simultaneouslyTo display the PIP window PIP function is effective at below source combinationsPOWER/ON II again Turning the projector offOn-Screen Display OSD menus On-Screen Display OSD structureMain menu Sub-menu Options System Setup DisplaySetup InformationPicture -- Basic menu Picture -- Advanced menuFunction Description Display menu System Setup menu Advanced Setup menu Information menu Care of the projector Cleaning the lensCleaning the projector case Storing the projectorLamp information Setting Lamp Mode as Dual-ReliableSetting Auto Power Off Getting to know the lamp hourTiming of replacing the lamp Replacing the lampStatus Message English Resetting the lamp timer Reset Lamp Timer? Indicators Power eventsLight Status & Description Troubleshooting Problem Cause RemedyElectrical SpecificationsOptical TerminalsDimensions Ceiling mount installationMm x 354.7 mm x 167 mm W x D x H Supported timing for PC input Timing chartFormat Resolution Refresh rate Frequency KHz MHzSupported timing for Hdmi Hdcp input Format Resolution Refresh rate Hz Freq. KHz Pixel Freq. MHzFormat Resolution Refresh rate Freq. KHz Pixel Freq MHz Supported timing for Edtv and Hdtv via Component inputsWarranty CopyrightDisclaimer