BenQ SH960 user manual Adjusting the sound, Setting the lamp mode, Muting the sound

Page 36

English

Adjusting the sound

The sound adjustments made as below will have an effect on the projector speaker(s). Be sure you have made a correct connection to the projector audio input. See "Connecting with video equipment" on page 17 for how the audio input is connected.

Muting the sound

To temporarily turn off the sound:

1.Press MENU/EXIT to open the OSD menu and press / to highlight the Advanced Setup menu.

2.Press to highlight Audio Settings and press ENTER. The Audio Settings page is displayed.

3.Highlight Mute and press / to select On.

If available, you can also press MUTE on the remote control to toggle projector audio between on and off.

Adjusting the sound level

To adjust the sound level, press VOLUME+/VOLUME- on the remote control, or:

1.Repeat steps 1-2above.

2.Press to highlight Volume and press / to select a desired sound level.

Turning off the Power On/Off Ring Tone

To turn off the ring tone:

1.Repeat steps 1-2above.

2.Press to highlight Power On/Off Ring Tone and press / to select Off.

The only way to change Power On/Off Ring Tone is setting On or Off here. Setting the sound mute or changing the sound level will not affect the Power On/Off Ring Tone.

Setting the lamp mode

This projector is capable of dual-lamp projection and provides several lamp modes for different purposes:

Lamp mode

 

User Benefit

Suitable environment

Dual-Brightest

• Delivering super-bright and clear images

Large, well lit meeting

Suitable for high-ambient-light environments

(Two lamps are used in normal

Allowing continuous and non-stop operation

rooms or auditoriums

mode)

 

under critical situations

 

 

 

 

 

 

 

 

Dual-Reliable

Extending the lamp life

Mid-large boardrooms

(Two lamps are used in

Allowing continuous and non-stop operation

economic mode)

 

under critical situations

 

 

 

 

 

Single-Alternative

 

 

 

(The lamp with shorter operating

Extending the total operation time

Normal sized rooms

hours is selected automatically

Reducing lamp replacement frequency

 

and used in normal mode)

 

 

 

 

 

 

 

Single-Eco

Extending the lamp life

 

(The lamp with shorter operating

Small to normal sized

hours is selected automatically

• Extending the total operation time

rooms

• Reducing lamp replacement frequency

and used in economic mode)

 

 

 

 

 

 

 

 

You can perform the following steps to choose a lamp mode according to your preference.

1.Press MENU/EXIT and then press / until the Advanced Setup menu is highlighted.

2.Press to highlight Lamp Settings and press ENTER.

3.Press to highlight Lamp Mode and press ENTER.

4.Press to highlight your preferred lamp mode and press ENTER.

5.A confirmation message displays. Highlight Yes and press ENTER.

36 Using the projector

Image 36
Contents Welcome Table of contents Important safety instructions Do not cover the projector with any item Moisture condensation Avoid volatile liquidsDisposal Shipping contents OverviewRemote control batteries Remote control operationCeiling mounting the projector Projector features Front and upper side view Rear viewUnder view Controls and functions Control panelRemote control MuteOperating the Laser pointer Choosing a location Floor FrontCeiling Front Floor RearObtaining a preferred projected image size Projection dimensions Installation for a 169 ratio screenInstallation for a 43 ratio screen HighestLens Height HShifting the projection lens To use the lens shift leverConnecting Hdmi devices PreparationsTerminal appearance Reference Picture quality ComponentConnecting component-video devices Connecting S-Video or video devicesConnecting a computer Connecting a monitorConnect the projector to a computer with a VGA cable Turning the projector on PreparationsUsing the OSD menu Selecting an input sourceChanging Color Space Using the menus Using a security cable lockUse / to highlight the System Setup menu Press MENU/EXIT twice* to leave and save the settingsUtilizing the password function Setting a passwordIf you forget the password To leave the OSD menu, press MENU/EXITEntering the password recall procedure Changing the passwordDisabling the password function Write down the number and turn off your projectorAdjusting the projected image Adjusting the projection angleAuto-adjusting the image Fine-tuning the image size and clarityCorrecting picture distortion Ii. See step iv below for further operationTwo parallel sides No parallel sidesUsing the preset and user modes Selecting a preset modeFine-tuning the selected picture mode To select a picture mode that suits your needSetting the User 1/User 2 mode Resetting the picture modeTo reset the picture mode to the preset factory values Renaming user modesFine-tuning the picture quality Setting Black Level Selecting a color temperatureAdvanced picture quality controls Controlling image claritySetting a preferred color temperature Selecting a Gamma settingAdjusting Brilliant Color To set a preferred color temperatureSetting Film Mode To adjust and store the settingsTo leave and save the settings, press MENU/EXIT Color ManagementSetting 3D Comb Filter Selecting the aspect ratioAbout the aspect ratio Using Panamorph lenses optional Image Using the entire resolutionAspect ratio Aspect ratio image 169 displayUtilizing FAQ function Hiding the imageFreezing the image Press EnterAdjusting the sound Setting the lamp modeAdjusting the sound level Turning off the Power On/Off Ring ToneConfiguring the Lan Control Settings Controlling the projector through a Lan environmentIf you are in a Dhcp environment If you are in a non-DHCP environmentIi To switch input source, click on your desired signal Controlling the projector remotely through a web browserAuto Source Menu itemCategory Item Input Length Maximum Number To activate High Altitude Mode Operating in a high altitude environmentDisplaying more than one image source simultaneously To display the PIP windowHighlight PIP and press / to select On PIP function is effective at below source combinationsPOWER/ON II again Turning the projector offOn-Screen Display OSD menus On-Screen Display OSD structureMain menu Sub-menu Options System Setup DisplaySetup InformationPicture -- Basic menu Picture -- Advanced menuFunction Description Display menu System Setup menu Advanced Setup menu Information menu Cleaning the lens Cleaning the projector caseCare of the projector Storing the projectorSetting Lamp Mode as Dual-Reliable Setting Auto Power OffLamp information Getting to know the lamp hourTiming of replacing the lamp Replacing the lampStatus Message English Resetting the lamp timer Reset Lamp Timer? Indicators Power eventsLight Status & Description Troubleshooting Problem Cause RemedySpecifications OpticalElectrical TerminalsDimensions Ceiling mount installationMm x 354.7 mm x 167 mm W x D x H Timing chart Format Resolution Refresh rate FrequencySupported timing for PC input KHz MHzFormat Resolution Refresh rate Hz Freq. KHz Pixel Freq. MHz Format Resolution Refresh rate Freq. KHz Pixel Freq MHzSupported timing for Hdmi Hdcp input Supported timing for Edtv and Hdtv via Component inputsWarranty CopyrightDisclaimer