BenQ SH960 user manual Resetting the lamp timer

Page 55

7.Insert the replacement lamp. Make sure it is pushed fully and firmly in place.

8.Tighten the screw securing the lamp box. Reconnect the lamp connector.

9.Ensure the handle is fully locked in place.

10. Replace the lamp cover.

11.Tighten the screws on the lamp cover.

12.Reapply power and turn the projector back on.

English

Notes

Please be careful to not over-tighten the screws.

Loose screws may cause a bad connection, which could result in malfunction.

Resetting the lamp timer

Do not reset the lamp timer if the lamp has not been replaced as this could cause damage.

Additional information

55

Image 55
Contents Welcome Table of contents Important safety instructions Do not cover the projector with any item Avoid volatile liquids Moisture condensationDisposal Overview Shipping contentsRemote control operation Remote control batteriesCeiling mounting the projector Projector features Rear view Front and upper side viewUnder view Control panel Controls and functionsMute Remote controlOperating the Laser pointer Floor Rear Choosing a locationFloor Front Ceiling FrontObtaining a preferred projected image size Installation for a 169 ratio screen Projection dimensionsHeight H Installation for a 43 ratio screenHighest LensTo use the lens shift lever Shifting the projection lensComponent Connecting Hdmi devicesPreparations Terminal appearance Reference Picture qualityConnecting S-Video or video devices Connecting component-video devicesConnecting a monitor Connecting a computerConnect the projector to a computer with a VGA cable Preparations Turning the projector onSelecting an input source Using the OSD menuChanging Color Space Press MENU/EXIT twice* to leave and save the settings Using the menusUsing a security cable lock Use / to highlight the System Setup menuTo leave the OSD menu, press MENU/EXIT Utilizing the password functionSetting a password If you forget the passwordWrite down the number and turn off your projector Entering the password recall procedureChanging the password Disabling the password functionFine-tuning the image size and clarity Adjusting the projected imageAdjusting the projection angle Auto-adjusting the imageNo parallel sides Correcting picture distortionIi. See step iv below for further operation Two parallel sidesTo select a picture mode that suits your need Using the preset and user modesSelecting a preset mode Fine-tuning the selected picture modeRenaming user modes Setting the User 1/User 2 modeResetting the picture mode To reset the picture mode to the preset factory valuesFine-tuning the picture quality Controlling image clarity Setting Black LevelSelecting a color temperature Advanced picture quality controlsTo set a preferred color temperature Setting a preferred color temperatureSelecting a Gamma setting Adjusting Brilliant ColorColor Management Setting Film ModeTo adjust and store the settings To leave and save the settings, press MENU/EXITSelecting the aspect ratio Setting 3D Comb FilterAbout the aspect ratio 169 display Using Panamorph lenses optionalImage Using the entire resolution Aspect ratio Aspect ratio imagePress Enter Utilizing FAQ functionHiding the image Freezing the imageTurning off the Power On/Off Ring Tone Adjusting the soundSetting the lamp mode Adjusting the sound levelIf you are in a non-DHCP environment Configuring the Lan Control SettingsControlling the projector through a Lan environment If you are in a Dhcp environmentMenu item Ii To switch input source, click on your desired signalControlling the projector remotely through a web browser Auto SourceCategory Item Input Length Maximum Number Operating in a high altitude environment To activate High Altitude ModePIP function is effective at below source combinations Displaying more than one image source simultaneouslyTo display the PIP window Highlight PIP and press / to select OnTurning the projector off POWER/ON II againOn-Screen Display OSD structure On-Screen Display OSD menusMain menu Sub-menu Options Display System SetupInformation SetupPicture -- Advanced menu Picture -- Basic menuFunction Description Display menu System Setup menu Advanced Setup menu Information menu Storing the projector Cleaning the lensCleaning the projector case Care of the projectorGetting to know the lamp hour Setting Lamp Mode as Dual-ReliableSetting Auto Power Off Lamp informationReplacing the lamp Timing of replacing the lampStatus Message English Resetting the lamp timer Reset Lamp Timer? Power events IndicatorsLight Status & Description Problem Cause Remedy TroubleshootingTerminals SpecificationsOptical ElectricalCeiling mount installation DimensionsMm x 354.7 mm x 167 mm W x D x H KHz MHz Timing chartFormat Resolution Refresh rate Frequency Supported timing for PC inputSupported timing for Edtv and Hdtv via Component inputs Format Resolution Refresh rate Hz Freq. KHz Pixel Freq. MHzFormat Resolution Refresh rate Freq. KHz Pixel Freq MHz Supported timing for Hdmi Hdcp inputCopyright WarrantyDisclaimer