Vidikron Vision 65, Vision 75 operation manual Using This Manual, If you need Turn to

Page 18

Introduction

1.2

Using This Manual

Graphic Conventions: These symbols appear in numerous places throughout the manual, to emphasize points that you must keep in mind to avoid problems with your equipment or injury:

Tip

TIPS highlight time-saving short cuts and helpful guidelines for using

certain features.

Note

NOTES emphasize text with unusual importance or special significance.

They also provide supplemental information.

 

Caution

CAUTIONS alert users that a given action or omitted action can degrade

performance or cause a malfunction.

 

WARNING

WARNINGS appear when a given action or omitted action can result in

damage to the equipment, or possible non-fatal injury to the user.

DANGER appears when a given action can cause severe injury or death.

DANGER!

Use the following table to locate the specific information you need in this manual.

If you need...

... Turn to page:

 

 

Information about obtaining service

iv

General information about the Vision Model 65 and Model 75 DLP

3

Home Theater Projectors

 

Installation instructions

13

First-time configuration instructions

33

Advanced configuration instructions

57

Troubleshooting tips

64

Specifications for the Vision Model 65 and Model 75 DLP Home

71

Theater Projectors

 

 

 

2

Vidikron Vision Model 65/Model 75 Installation/Operation Manual

Image 18
Contents 65/75 Page TWO Year Limited Warranty RIGHTS, Limits and Exclusions Product Information Retain for Your Records Important Safety Instructions Compliance Information Declaration of ConformityFCC Part Table of Hazardous Substances Model Name Vision Model 75 Series 1Table of Contents Maintenance and Troubleshooting OperationSerial Communications Table of Contents Xiv 1List of Figures CIE 1931 Chromaticity Diagram 1Introduction About This ManualThis Manual Using This Manual If you need Turn toDescription, Features and Benefits Optional Accessories Vision 65/75 at a Glance Vision 65/75 Front/Side/Top ViewPOWER/STANDBY LED Indicates power status as follows Temp LEDCable Access Door Open to access connectors Vision 65/75 Rear/Bottom/Side ViewHdmi 2 Digital Comp 1 RCA connectors Vision 65/75 Rear PanelVision 65/75 Remote Control Volt 250 mA Trigger Output 3.5-mm, mini phono jackComp 2 / RGB VID S-Video On / OFFSource Selection Buttons Cursor KeysContrast Picture Adjustment Buttons BRT BrightnessMemory Preset Buttons COL ColorPicture-In-Picture PIP Controls Lens3Installation Remote ControlOperation Step Procedure For Details, Refer to Quick SetupInstallation Overview If installing a CineWide-equipped projector InstallInstallation Type Installation ConsiderationsProjector Installation Options Advantages ConsiderationsThrow Ratios for the Vision 65/75 Series Throw Range Throw RatioProjector Model Ceiling Installation Floor InstallationVertical and Horizontal Position Up/down vertical lens shift percentages Installing the Optional CineWide Lens Mount Fixed CineWide Base Plate Cylindrical LensAutoScope motor assembly MotorVision 65/75 with Ceiling Mount Adapters/Projector Stands Install Lens Motor AutoScope Lens Motor InstallationBase Plate Prismatic Lens Do not OVER-TIGHTEN the ScrewsVision 65/CineWide or Vision 75/CineWide Mounting the Vision 65/75 Floor Mounting UprightAdjusting the Projector Using the On-Screen Menus onHeight or Projection Angle Connecting Source Connections to the Vision 65/7565/75 11. RGB Connections 13. Composite, S-Video and Component Video Connections Connection 14. RS-232 Control System Connection16. Connecting the 12-Volt Trigger Output to Other Equipment AutoScope Lens Motor RearTurning on the Power Power sourceZoom Changing the OSD Language Adjusting the Picture OrientationPrimary Lens Adjustments Zo om Out FocusInstalling and Adjusting the CineWide Anamorphic Lens These instructions Attach Lens Mounting Assembly to Lens Motor Carriage Plate 18. Attaching the Anamorphic Lens to the Lens Adapter RingAdjusting the Horizontal X Lens Position Installation Adjusting the Geometry Anamorphic Lens Top ViewAdjustment Whitney PrismaticAdjusting the Lens Height Y Anamorphic Lens Top View Selecting Video Memory Selecting an Aspect Ratio Adjusting the Picture4Operation Selecting An Input SourceUsing Picture-In-Picture PIP Using the On-Screen MenusInstallation SetupPicture Adjust Source SelectPicture Adjust Perform the adjustments in the order listed hereSource Select You must enter a passcode to access the ISF menu Typical Pluge Pattern for Adjusting BrightnessTypical Gray Bar Pattern for Adjusting Contrast Gray Yellow Cyan Green Magenta Red Blue Typical Test Pattern for Adjusting Sharpness Aspect Ratio Settings Aspect RatioDescription Cinema Installation Fit a 2.351 screenHorizontal Keystone Correction Vertical Keystone CorrectionPincushion Correction Operation Setup InformationRefer to the instructions for your computer Is powered off, then on again This menu should be used by ISF-certified technicians onlySettings reduce the image brightness CIE 1931 Chromaticity Diagram Operation 5Maintenance and Troubleshooting Lamp ReplacementLamp assembly for replacement Troubleshooting Tips Troubleshooting ChartSymptom Possible Causes Solution Troubleshooting Chart Maintenance and Troubleshooting Serial Commands Serial Command SyntaxRS-232 Connection and Port Configuration 6Serial CommunicationsSerial Communications Serial Commands Serial Communications 7Specifications Vision 65/75 SpecificationsIndustry-Standard Specifications Vision Model 65 Series Specifications Vision Model 75 SeriesHome Theater Calibration Specifications Vision Industry-Standard Specifications Vision Model 75 SeriesWeight without lens Power RequirementsDimensions Limited WarrantyVision 65/75 Dimensions Vision 65/75 Dimensions with Optional Fixed Anamorphic LensSupported Signal Timings Supported Timings Format ResolutionMHz Supported Signal Timings Format Resolution Refresh Rate Hz Horizontal Pixel FrequencySdtv Signals Video / S-Video Specifications Page 020-0715-02 Rev. a March