Vidikron Vision 75, Vision 65 operation manual AutoScope Lens Motor Rear

Page 47

Installation

If you are installing a Vision 65/75/CineWide with AutoScope, use the cable supplied with the AutoScope Lens Motor to connect the motor to the 12-volt trigger output as shown in Figure 3-15.

Connecting 12-Volt Trigger Output to External Theater Equipment

S-VID /

VID-S

3.5-mm mini plug

AutoScope

Lens Motor (Rear)

Power

AC Input

Switch

 

Figure 3-15. Connecting the 12-Volt Trigger Output to the AutoScope Lens Motor

If your home theater contains a retractable screen, screen mask or other 12-volt trigger-activated equipment, connect it to the 12-volt trigger output as shown in Figure 3-16.

S-VID /

VID-S

3.5-mm mini plug

to other,

 

 

12-volt

 

Black = Ground (Sleeve)

trigger-activated equipment

 

 

 

 

Red = +12V (Tip)

(screen, screen mask etc.)

 

Figure 3-16. Connecting the 12-Volt Trigger Output to Other Equipment

Vidikron Vision Model 65/Model 75 Installation/Operation Manual

31

Image 47
Contents 65/75 Page TWO Year Limited Warranty RIGHTS, Limits and Exclusions Product Information Retain for Your Records Important Safety Instructions Declaration of Conformity Compliance InformationFCC Part Table of Hazardous Substances Model Name Vision Model 75 Series 1Table of Contents Operation Maintenance and TroubleshootingSerial Communications Table of Contents Xiv 1List of Figures CIE 1931 Chromaticity Diagram This Manual 1IntroductionAbout This Manual If you need Turn to Using This ManualDescription, Features and Benefits Optional Accessories Vision 65/75 Front/Side/Top View Vision 65/75 at a GlanceTemp LED POWER/STANDBY LED Indicates power status as followsVision 65/75 Rear/Bottom/Side View Cable Access Door Open to access connectorsVision 65/75 Rear Panel Hdmi 2 Digital Comp 1 RCA connectorsComp 2 / RGB Vision 65/75 Remote ControlVolt 250 mA Trigger Output 3.5-mm, mini phono jack Cursor Keys On / OFFSource Selection Buttons VID S-VideoCOL Color Picture Adjustment Buttons BRT BrightnessMemory Preset Buttons ContrastLens Picture-In-Picture PIP ControlsOperation 3InstallationRemote Control If installing a CineWide-equipped projector Install Quick SetupInstallation Overview Step Procedure For Details, Refer toAdvantages Considerations Installation ConsiderationsProjector Installation Options Installation TypeProjector Model Throw Ratios for the Vision 65/75 SeriesThrow Range Throw Ratio Vertical and Horizontal Position Ceiling InstallationFloor Installation Up/down vertical lens shift percentages Fixed CineWide Base Plate Cylindrical Lens Installing the Optional CineWide Lens MountMotor AutoScope motor assemblyVision 65/75 with Ceiling Mount Adapters/Projector Stands AutoScope Lens Motor Installation Install Lens MotorDo not OVER-TIGHTEN the Screws Base Plate Prismatic LensVision 65/CineWide or Vision 75/CineWide Floor Mounting Upright Mounting the Vision 65/75Height or Projection Angle Adjusting the ProjectorUsing the On-Screen Menus on 65/75 Connecting SourceConnections to the Vision 65/75 11. RGB Connections 13. Composite, S-Video and Component Video Connections 14. RS-232 Control System Connection ConnectionAutoScope Lens Motor Rear 16. Connecting the 12-Volt Trigger Output to Other EquipmentPower source Turning on the PowerZo om Out Focus Changing the OSD Language Adjusting the Picture OrientationPrimary Lens Adjustments ZoomInstalling and Adjusting the CineWide Anamorphic Lens These instructions 18. Attaching the Anamorphic Lens to the Lens Adapter Ring Attach Lens Mounting Assembly to Lens Motor Carriage PlateAdjusting the Horizontal X Lens Position Installation Anamorphic Lens Top View Adjusting the GeometryWhitney Prismatic AdjustmentAdjusting the Lens Height Y Anamorphic Lens Top View Selecting An Input Source Selecting an Aspect Ratio Adjusting the Picture4Operation Selecting Video MemoryUsing the On-Screen Menus Using Picture-In-Picture PIPSource Select SetupPicture Adjust InstallationSource Select Picture AdjustPerform the adjustments in the order listed here Typical Pluge Pattern for Adjusting Brightness You must enter a passcode to access the ISF menuTypical Gray Bar Pattern for Adjusting Contrast Gray Yellow Cyan Green Magenta Red Blue Typical Test Pattern for Adjusting Sharpness Description Aspect Ratio SettingsAspect Ratio Cinema Fit a 2.351 screen InstallationVertical Keystone Correction Horizontal Keystone CorrectionPincushion Correction Operation Information SetupRefer to the instructions for your computer This menu should be used by ISF-certified technicians only Is powered off, then on againSettings reduce the image brightness CIE 1931 Chromaticity Diagram Operation Lamp assembly for replacement 5Maintenance and TroubleshootingLamp Replacement Symptom Possible Causes Solution Troubleshooting TipsTroubleshooting Chart Troubleshooting Chart Maintenance and Troubleshooting 6Serial Communications Serial Command SyntaxRS-232 Connection and Port Configuration Serial CommandsSerial Communications Serial Commands Serial Communications Vision 65/75 Specifications 7SpecificationsIndustry-Standard Specifications Vision Model 75 Series Specifications Vision Model 75 SeriesHome Theater Calibration Specifications Vision Industry-Standard Specifications Vision Model 65 SeriesLimited Warranty Power RequirementsDimensions Weight without lensVision 65/75 Dimensions with Optional Fixed Anamorphic Lens Vision 65/75 DimensionsMHz Supported Signal Timings Supported TimingsFormat Resolution Format Resolution Refresh Rate Hz Horizontal Pixel Frequency Supported Signal TimingsSdtv Signals Video / S-Video Specifications Page 020-0715-02 Rev. a March