Vidikron Vision 65, Vision 75 operation manual Operation, Maintenance and Troubleshooting

Page 12

Table of Contents

	Mounting the Vision 65/75	25
	Floor Mounting (Upright)	25
	Ceiling Mounting (Inverted)	25
	Adjusting the Projector Height or Projection Angle	26
	Connections to the Vision 65/75	27
	Connector Panel Access	27
	Connecting Source Components to the Vision 65/75	27
	RS-232 Controller Connection	30
	Connecting 12-Volt Trigger Output to External Theater Equipment	31
	Connecting to AC Power	32
	Turning on the Power	32
	Primary Lens Adjustments	33
	Focus and Zoom	33
	Vertical Lens Shift	33
	Changing the OSD Language	33
	Adjusting the Picture Orientation	33
	Installing and Adjusting the CineWide Anamorphic Lens	34
	Cylindrical Anamorphic Lens Installation and Adjustment	35
	Whitney (Prismatic) Anamorphic Lens Installation and Adjustment	40
4.	Operation	43
	Selecting Video Memory	43
	Selecting an Aspect Ratio	43
	Adjusting the Picture	43
	Selecting An Input Source	43
	Using Picture-In-Picture (PIP)	44
	Using the On-Screen Menus	44
	Main Menu	46
	Source Select	46
	Picture Adjust	46
	Aspect Ratio	51
	Installation	53
	Information	57
	Setup	57
	ISF	59
5.	Maintenance and Troubleshooting	63
	Lamp Replacement	63
	Troubleshooting Tips	64

xii	Vidikron Vision Model 65/Model 75 Installation/Operation Manual

Image 12

Contents 65/75 Page TWO Year Limited Warranty RIGHTS, Limits and Exclusions Product Information Retain for Your Records Important Safety Instructions Compliance Information Declaration of ConformityFCC Part Table of Hazardous Substances Model Name Vision Model 75 Series 1Table of Contents Maintenance and Troubleshooting OperationSerial Communications Table of Contents Xiv 1List of Figures CIE 1931 Chromaticity Diagram 1Introduction About This ManualThis Manual Using This Manual If you need Turn toDescription, Features and Benefits Optional Accessories Vision 65/75 at a Glance Vision 65/75 Front/Side/Top ViewPOWER/STANDBY LED Indicates power status as follows Temp LEDCable Access Door Open to access connectors Vision 65/75 Rear/Bottom/Side ViewHdmi 2 Digital Comp 1 RCA connectors Vision 65/75 Rear PanelVision 65/75 Remote Control Volt 250 mA Trigger Output 3.5-mm, mini phono jackComp 2 / RGB On / OFF Source Selection ButtonsVID S-Video Cursor KeysPicture Adjustment Buttons BRT Brightness Memory Preset ButtonsContrast COL ColorPicture-In-Picture PIP Controls Lens3Installation Remote ControlOperation Quick Setup Installation OverviewStep Procedure For Details, Refer to If installing a CineWide-equipped projector InstallInstallation Considerations Projector Installation OptionsInstallation Type Advantages ConsiderationsThrow Ratios for the Vision 65/75 Series Throw Range Throw RatioProjector Model Ceiling Installation Floor InstallationVertical and Horizontal Position Up/down vertical lens shift percentages Installing the Optional CineWide Lens Mount Fixed CineWide Base Plate Cylindrical LensAutoScope motor assembly MotorVision 65/75 with Ceiling Mount Adapters/Projector Stands Install Lens Motor AutoScope Lens Motor InstallationBase Plate Prismatic Lens Do not OVER-TIGHTEN the ScrewsVision 65/CineWide or Vision 75/CineWide Mounting the Vision 65/75 Floor Mounting UprightAdjusting the Projector Using the On-Screen Menus onHeight or Projection Angle Connecting Source Connections to the Vision 65/7565/75 11. RGB Connections 13. Composite, S-Video and Component Video Connections Connection 14. RS-232 Control System Connection16. Connecting the 12-Volt Trigger Output to Other Equipment AutoScope Lens Motor RearTurning on the Power Power sourceChanging the OSD Language Adjusting the Picture Orientation Primary Lens AdjustmentsZoom Zo om Out FocusInstalling and Adjusting the CineWide Anamorphic Lens These instructions Attach Lens Mounting Assembly to Lens Motor Carriage Plate 18. Attaching the Anamorphic Lens to the Lens Adapter RingAdjusting the Horizontal X Lens Position Installation Adjusting the Geometry Anamorphic Lens Top ViewAdjustment Whitney PrismaticAdjusting the Lens Height Y Anamorphic Lens Top View Selecting an Aspect Ratio Adjusting the Picture 4OperationSelecting Video Memory Selecting An Input SourceUsing Picture-In-Picture PIP Using the On-Screen MenusSetup Picture AdjustInstallation Source SelectPicture Adjust Perform the adjustments in the order listed hereSource Select You must enter a passcode to access the ISF menu Typical Pluge Pattern for Adjusting BrightnessTypical Gray Bar Pattern for Adjusting Contrast Gray Yellow Cyan Green Magenta Red Blue Typical Test Pattern for Adjusting Sharpness Aspect Ratio Settings Aspect RatioDescription Cinema Installation Fit a 2.351 screenHorizontal Keystone Correction Vertical Keystone CorrectionPincushion Correction Operation Setup InformationRefer to the instructions for your computer Is powered off, then on again This menu should be used by ISF-certified technicians onlySettings reduce the image brightness CIE 1931 Chromaticity Diagram Operation 5Maintenance and Troubleshooting Lamp ReplacementLamp assembly for replacement Troubleshooting Tips Troubleshooting ChartSymptom Possible Causes Solution Troubleshooting Chart Maintenance and Troubleshooting Serial Command Syntax RS-232 Connection and Port ConfigurationSerial Commands 6Serial CommunicationsSerial Communications Serial Commands Serial Communications 7Specifications Vision 65/75 SpecificationsSpecifications Vision Model 75 Series Home Theater Calibration Specifications VisionIndustry-Standard Specifications Vision Model 65 Series Industry-Standard Specifications Vision Model 75 SeriesPower Requirements DimensionsWeight without lens Limited WarrantyVision 65/75 Dimensions Vision 65/75 Dimensions with Optional Fixed Anamorphic LensSupported Signal Timings Supported Timings Format ResolutionMHz Supported Signal Timings Format Resolution Refresh Rate Hz Horizontal Pixel FrequencySdtv Signals Video / S-Video Specifications Page 020-0715-02 Rev. a March