Vidikron Vision 75, Vision 65 operation manual You must enter a passcode to access the ISF menu

Page 63

Operation

Picture Memory: For each input, the Vision 65/75 lets you store picture quality settings as presets that you can recall at a later time. You can create up to four presets per input and resolution, to accommodate changing lighting conditions or viewer preferences.

To select a picture memory preset, highlight Picture Memory in the Picture Adjust menu. Then, press or to select “Custom 1,” “Custom 2,” “ISF Night” or “ISF Day.” When you select “Custom 1” or “Custom 2,” any changes to picture quality settings are stored in the selected preset.

1. To store changes to the ISF Night or ISF Day Picture Memory preset,

Note select that Picture Memory in the ISF menu (refer to ISF on page 59).

You must enter a passcode to access the ISF menu.

2.The Picture Memory selection you make here is not retained when the projector is powered off, then on again. To specify which Picture Memory should take effect when the projector is powered on, select it in the ISF menu.

Copy Settings: When you select the “Custom 1” or “Custom 2” Picture Memory preset, you can copy the settings from another preset to the selected preset. This gives you a convenient starting point for creating a new, custom preset. To do this, select Copy Settings from the Picture Adjust menu and press . Then, choose “Custom 1,” “Custom 2,” “ISF Night” or “ISF Day.”

To copy changes to the ISF Night or ISF Day Picture Memory preset, select

Note that Picture Memory in the ISF menu (refer to ISF on page 59). You must enter a passcode to access the ISF menu.

Brightness: On your external test pattern source, select a PLUGE pattern. (PLUGE is an acronym for “Picture Line-Up Generation Equipment.”) Figure 4-2shows a typical PLUGE pattern.

Below Black

Above Black

Figure 4-2. Typical PLUGE Pattern for Adjusting Brightness

PLUGE patterns vary but generally consist of some combination of black, white and gray areas against a black background. The example above includes two vertical bars and four shaded boxes.

Vidikron Vision Model 65/Model 75 Installation/Operation Manual

47

Image 63
Contents 65/75 Page TWO Year Limited Warranty RIGHTS, Limits and Exclusions Product Information Retain for Your Records Important Safety Instructions Declaration of Conformity Compliance InformationFCC Part Table of Hazardous Substances Model Name Vision Model 75 Series 1Table of Contents Operation Maintenance and TroubleshootingSerial Communications Table of Contents Xiv 1List of Figures CIE 1931 Chromaticity Diagram 1Introduction About This ManualThis Manual If you need Turn to Using This ManualDescription, Features and Benefits Optional Accessories Vision 65/75 Front/Side/Top View Vision 65/75 at a GlanceTemp LED POWER/STANDBY LED Indicates power status as followsVision 65/75 Rear/Bottom/Side View Cable Access Door Open to access connectorsVision 65/75 Rear Panel Hdmi 2 Digital Comp 1 RCA connectorsVision 65/75 Remote Control Volt 250 mA Trigger Output 3.5-mm, mini phono jackComp 2 / RGB Cursor Keys On / OFFSource Selection Buttons VID S-VideoCOL Color Picture Adjustment Buttons BRT BrightnessMemory Preset Buttons ContrastLens Picture-In-Picture PIP Controls3Installation Remote ControlOperation If installing a CineWide-equipped projector Install Quick SetupInstallation Overview Step Procedure For Details, Refer toAdvantages Considerations Installation ConsiderationsProjector Installation Options Installation TypeThrow Ratios for the Vision 65/75 Series Throw Range Throw RatioProjector Model Ceiling Installation Floor InstallationVertical and Horizontal Position Up/down vertical lens shift percentages Fixed CineWide Base Plate Cylindrical Lens Installing the Optional CineWide Lens MountMotor AutoScope motor assemblyVision 65/75 with Ceiling Mount Adapters/Projector Stands AutoScope Lens Motor Installation Install Lens MotorDo not OVER-TIGHTEN the Screws Base Plate Prismatic LensVision 65/CineWide or Vision 75/CineWide Floor Mounting Upright Mounting the Vision 65/75Adjusting the Projector Using the On-Screen Menus onHeight or Projection Angle Connecting Source Connections to the Vision 65/7565/75 11. RGB Connections 13. Composite, S-Video and Component Video Connections 14. RS-232 Control System Connection ConnectionAutoScope Lens Motor Rear 16. Connecting the 12-Volt Trigger Output to Other EquipmentPower source Turning on the PowerZo om Out Focus Changing the OSD Language Adjusting the Picture OrientationPrimary Lens Adjustments ZoomInstalling and Adjusting the CineWide Anamorphic Lens These instructions 18. Attaching the Anamorphic Lens to the Lens Adapter Ring Attach Lens Mounting Assembly to Lens Motor Carriage PlateAdjusting the Horizontal X Lens Position Installation Anamorphic Lens Top View Adjusting the GeometryWhitney Prismatic AdjustmentAdjusting the Lens Height Y Anamorphic Lens Top View Selecting An Input Source Selecting an Aspect Ratio Adjusting the Picture4Operation Selecting Video MemoryUsing the On-Screen Menus Using Picture-In-Picture PIPSource Select SetupPicture Adjust InstallationPicture Adjust Perform the adjustments in the order listed hereSource Select Typical Pluge Pattern for Adjusting Brightness You must enter a passcode to access the ISF menuTypical Gray Bar Pattern for Adjusting Contrast Gray Yellow Cyan Green Magenta Red Blue Typical Test Pattern for Adjusting Sharpness Aspect Ratio Settings Aspect RatioDescription Cinema Fit a 2.351 screen InstallationVertical Keystone Correction Horizontal Keystone CorrectionPincushion Correction Operation Information SetupRefer to the instructions for your computer This menu should be used by ISF-certified technicians only Is powered off, then on againSettings reduce the image brightness CIE 1931 Chromaticity Diagram Operation 5Maintenance and Troubleshooting Lamp ReplacementLamp assembly for replacement Troubleshooting Tips Troubleshooting ChartSymptom Possible Causes Solution Troubleshooting Chart Maintenance and Troubleshooting 6Serial Communications Serial Command SyntaxRS-232 Connection and Port Configuration Serial CommandsSerial Communications Serial Commands Serial Communications Vision 65/75 Specifications 7SpecificationsIndustry-Standard Specifications Vision Model 75 Series Specifications Vision Model 75 SeriesHome Theater Calibration Specifications Vision Industry-Standard Specifications Vision Model 65 SeriesLimited Warranty Power RequirementsDimensions Weight without lensVision 65/75 Dimensions with Optional Fixed Anamorphic Lens Vision 65/75 DimensionsSupported Signal Timings Supported Timings Format ResolutionMHz Format Resolution Refresh Rate Hz Horizontal Pixel Frequency Supported Signal TimingsSdtv Signals Video / S-Video Specifications Page 020-0715-02 Rev. a March