Vidikron Vision 65, Vision 75 operation manual Picture-In-Picture PIP Controls, Lens

Page 28

Controls and Functions

9.Picture-In-Picture (PIP) Controls:

ACT

Press to switch to the active window in PIP mode.

PIP

Press to activate PIP mode.

PIP+

Press to enlarge the PIP window.

PIP-

Press to shrink the size of the PIP window.

10.LENS

Press to access the lens shift controls.

12

Vidikron Vision Model 65/Model 75 Installation/Operation Manual

Image 28
Contents 65/75 Page TWO Year Limited Warranty RIGHTS, Limits and Exclusions Product Information Retain for Your Records Important Safety Instructions Compliance Information Declaration of ConformityFCC Part Table of Hazardous Substances Model Name Vision Model 75 Series 1Table of Contents Maintenance and Troubleshooting OperationSerial Communications Table of Contents Xiv 1List of Figures CIE 1931 Chromaticity Diagram About This Manual 1IntroductionThis Manual Using This Manual If you need Turn toDescription, Features and Benefits Optional Accessories Vision 65/75 at a Glance Vision 65/75 Front/Side/Top ViewPOWER/STANDBY LED Indicates power status as follows Temp LEDCable Access Door Open to access connectors Vision 65/75 Rear/Bottom/Side ViewHdmi 2 Digital Comp 1 RCA connectors Vision 65/75 Rear PanelVolt 250 mA Trigger Output 3.5-mm, mini phono jack Vision 65/75 Remote ControlComp 2 / RGB On / OFF Source Selection ButtonsVID S-Video Cursor KeysPicture Adjustment Buttons BRT Brightness Memory Preset ButtonsContrast COL ColorPicture-In-Picture PIP Controls LensRemote Control 3InstallationOperation Quick Setup Installation OverviewStep Procedure For Details, Refer to If installing a CineWide-equipped projector InstallInstallation Considerations Projector Installation OptionsInstallation Type Advantages ConsiderationsThrow Range Throw Ratio Throw Ratios for the Vision 65/75 SeriesProjector Model Floor Installation Ceiling InstallationVertical and Horizontal Position Up/down vertical lens shift percentages Installing the Optional CineWide Lens Mount Fixed CineWide Base Plate Cylindrical LensAutoScope motor assembly MotorVision 65/75 with Ceiling Mount Adapters/Projector Stands Install Lens Motor AutoScope Lens Motor InstallationBase Plate Prismatic Lens Do not OVER-TIGHTEN the ScrewsVision 65/CineWide or Vision 75/CineWide Mounting the Vision 65/75 Floor Mounting UprightUsing the On-Screen Menus on Adjusting the ProjectorHeight or Projection Angle Connections to the Vision 65/75 Connecting Source65/75 11. RGB Connections 13. Composite, S-Video and Component Video Connections Connection 14. RS-232 Control System Connection16. Connecting the 12-Volt Trigger Output to Other Equipment AutoScope Lens Motor RearTurning on the Power Power sourceChanging the OSD Language Adjusting the Picture Orientation Primary Lens AdjustmentsZoom Zo om Out FocusInstalling and Adjusting the CineWide Anamorphic Lens These instructions Attach Lens Mounting Assembly to Lens Motor Carriage Plate 18. Attaching the Anamorphic Lens to the Lens Adapter RingAdjusting the Horizontal X Lens Position Installation Adjusting the Geometry Anamorphic Lens Top ViewAdjustment Whitney PrismaticAdjusting the Lens Height Y Anamorphic Lens Top View Selecting an Aspect Ratio Adjusting the Picture 4OperationSelecting Video Memory Selecting An Input SourceUsing Picture-In-Picture PIP Using the On-Screen MenusSetup Picture AdjustInstallation Source SelectPerform the adjustments in the order listed here Picture AdjustSource Select You must enter a passcode to access the ISF menu Typical Pluge Pattern for Adjusting BrightnessTypical Gray Bar Pattern for Adjusting Contrast Gray Yellow Cyan Green Magenta Red Blue Typical Test Pattern for Adjusting Sharpness Aspect Ratio Aspect Ratio SettingsDescription Cinema Installation Fit a 2.351 screenHorizontal Keystone Correction Vertical Keystone CorrectionPincushion Correction Operation Setup InformationRefer to the instructions for your computer Is powered off, then on again This menu should be used by ISF-certified technicians onlySettings reduce the image brightness CIE 1931 Chromaticity Diagram Operation Lamp Replacement 5Maintenance and TroubleshootingLamp assembly for replacement Troubleshooting Chart Troubleshooting TipsSymptom Possible Causes Solution Troubleshooting Chart Maintenance and Troubleshooting Serial Command Syntax RS-232 Connection and Port ConfigurationSerial Commands 6Serial CommunicationsSerial Communications Serial Commands Serial Communications 7Specifications Vision 65/75 SpecificationsSpecifications Vision Model 75 Series Home Theater Calibration Specifications VisionIndustry-Standard Specifications Vision Model 65 Series Industry-Standard Specifications Vision Model 75 SeriesPower Requirements DimensionsWeight without lens Limited WarrantyVision 65/75 Dimensions Vision 65/75 Dimensions with Optional Fixed Anamorphic LensFormat Resolution Supported Signal Timings Supported TimingsMHz Supported Signal Timings Format Resolution Refresh Rate Hz Horizontal Pixel FrequencySdtv Signals Video / S-Video Specifications Page 020-0715-02 Rev. a March