Vidikron Vision 65, Vision 75 Temp LED, POWER/STANDBY LED Indicates power status as follows

Page 22

Controls and Functions

5.POWER/STANDBY LED Indicates power status as follows:

•Orange when the projector is in standby mode

•Flashes green for approximately 45 seconds after the projector is turned on to indicate that the lamp is warming up

•Green during normal operation

•Flashes orange for approximately 110 seconds after the projector is turned off to indicate that the lamp is cooling down

•Red when an internal failure requiring service has occurred

6.TEMP LED

Indicates fan status and internal temperature as follows:

•Off during normal operation

•Red when internal temperature is too high or a fan failure occurs

7.INTAKE VENT

8. VIDIKRON LOGO

The logo can be rotated to match the projector orientation: inverted (ceiling-mounted) or upright. To rotate the logo, grip it at the sides, pull it away from the projector and rotate it 180 degrees.

9.FRONT IR SENSOR

10.PROJECTION LENS

To adjust the focus, grasp the lens by the outer ring and rotate it.

6	Vidikron Vision Model 65/Model 75 Installation/Operation Manual

Image 22

Contents 65/75 Page TWO Year Limited Warranty RIGHTS, Limits and Exclusions Product Information Retain for Your Records Important Safety Instructions Compliance Information Declaration of ConformityFCC Part Table of Hazardous Substances Model Name Vision Model 75 Series 1Table of Contents Maintenance and Troubleshooting OperationSerial Communications Table of Contents Xiv 1List of Figures CIE 1931 Chromaticity Diagram About This Manual 1IntroductionThis Manual Using This Manual If you need Turn toDescription, Features and Benefits Optional Accessories Vision 65/75 at a Glance Vision 65/75 Front/Side/Top ViewPOWER/STANDBY LED Indicates power status as follows Temp LEDCable Access Door Open to access connectors Vision 65/75 Rear/Bottom/Side ViewHdmi 2 Digital Comp 1 RCA connectors Vision 65/75 Rear PanelVolt 250 mA Trigger Output 3.5-mm, mini phono jack Vision 65/75 Remote ControlComp 2 / RGB VID S-Video On / OFFSource Selection Buttons Cursor KeysContrast Picture Adjustment Buttons BRT BrightnessMemory Preset Buttons COL ColorPicture-In-Picture PIP Controls LensRemote Control 3InstallationOperation Step Procedure For Details, Refer to Quick SetupInstallation Overview If installing a CineWide-equipped projector InstallInstallation Type Installation ConsiderationsProjector Installation Options Advantages ConsiderationsThrow Range Throw Ratio Throw Ratios for the Vision 65/75 SeriesProjector Model Floor Installation Ceiling InstallationVertical and Horizontal Position Up/down vertical lens shift percentages Installing the Optional CineWide Lens Mount Fixed CineWide Base Plate Cylindrical LensAutoScope motor assembly MotorVision 65/75 with Ceiling Mount Adapters/Projector Stands Install Lens Motor AutoScope Lens Motor InstallationBase Plate Prismatic Lens Do not OVER-TIGHTEN the ScrewsVision 65/CineWide or Vision 75/CineWide Mounting the Vision 65/75 Floor Mounting UprightUsing the On-Screen Menus on Adjusting the ProjectorHeight or Projection Angle Connections to the Vision 65/75 Connecting Source65/75 11. RGB Connections 13. Composite, S-Video and Component Video Connections Connection 14. RS-232 Control System Connection16. Connecting the 12-Volt Trigger Output to Other Equipment AutoScope Lens Motor RearTurning on the Power Power sourceZoom Changing the OSD Language Adjusting the Picture OrientationPrimary Lens Adjustments Zo om Out FocusInstalling and Adjusting the CineWide Anamorphic Lens These instructions Attach Lens Mounting Assembly to Lens Motor Carriage Plate 18. Attaching the Anamorphic Lens to the Lens Adapter RingAdjusting the Horizontal X Lens Position Installation Adjusting the Geometry Anamorphic Lens Top ViewAdjustment Whitney PrismaticAdjusting the Lens Height Y Anamorphic Lens Top View Selecting Video Memory Selecting an Aspect Ratio Adjusting the Picture4Operation Selecting An Input SourceUsing Picture-In-Picture PIP Using the On-Screen MenusInstallation SetupPicture Adjust Source SelectPerform the adjustments in the order listed here Picture AdjustSource Select You must enter a passcode to access the ISF menu Typical Pluge Pattern for Adjusting BrightnessTypical Gray Bar Pattern for Adjusting Contrast Gray Yellow Cyan Green Magenta Red Blue Typical Test Pattern for Adjusting Sharpness Aspect Ratio Aspect Ratio SettingsDescription Cinema Installation Fit a 2.351 screenHorizontal Keystone Correction Vertical Keystone CorrectionPincushion Correction Operation Setup InformationRefer to the instructions for your computer Is powered off, then on again This menu should be used by ISF-certified technicians onlySettings reduce the image brightness CIE 1931 Chromaticity Diagram Operation Lamp Replacement 5Maintenance and TroubleshootingLamp assembly for replacement Troubleshooting Chart Troubleshooting TipsSymptom Possible Causes Solution Troubleshooting Chart Maintenance and Troubleshooting Serial Commands Serial Command SyntaxRS-232 Connection and Port Configuration 6Serial CommunicationsSerial Communications Serial Commands Serial Communications 7Specifications Vision 65/75 SpecificationsIndustry-Standard Specifications Vision Model 65 Series Specifications Vision Model 75 SeriesHome Theater Calibration Specifications Vision Industry-Standard Specifications Vision Model 75 SeriesWeight without lens Power RequirementsDimensions Limited WarrantyVision 65/75 Dimensions Vision 65/75 Dimensions with Optional Fixed Anamorphic LensFormat Resolution Supported Signal Timings Supported TimingsMHz Supported Signal Timings Format Resolution Refresh Rate Hz Horizontal Pixel FrequencySdtv Signals Video / S-Video Specifications Page 020-0715-02 Rev. a March