Vidikron Vision 75, Vision 65 operation manual Gray Yellow Cyan Green Magenta Red Blue

Page 65

Operation

Color: On your external test pattern source, select a color bar pattern like the one shown in

Figure 4-4.

gray

yellow

cyan

green

magenta

red

blue

Figure 4-4. Typical Color Bar Pattern for Adjusting Color Saturation and Tint

Select Color from the Picture Adjust menu and press ENTER. While looking at the color bar pattern through a blue filter, adjust the color saturation level until the outermost (gray and blue) color bars appear to be a single shade of blue:

gray

yellow

cyan

green

magenta

red

blue

Tint: Tint or “hue” is essentially the ratio of red to green in the color portion of the image. When tint is decreased, the image appears redder; when it is increased the image appears greener. To set the tint, select Tint from the Picture Adjust menu and press ENTER. While looking at the color bar pattern through a blue filter, adjust the tint level until the cyan and magenta color bars (on either side of the green bar) appear to be a single shade of blue.

Like the Brightness and Contrast controls, the color and tint controls are

Note interactive. A change to one may require a subtle change to the other in order to achieve the optimum setting.

Vidikron Vision Model 65/Model 75 Installation/Operation Manual

49

Image 65
Contents 65/75 Page TWO Year Limited Warranty RIGHTS, Limits and Exclusions Product Information Retain for Your Records Important Safety Instructions Declaration of Conformity Compliance InformationFCC Part Table of Hazardous Substances Model Name Vision Model 75 Series 1Table of Contents Operation Maintenance and TroubleshootingSerial Communications Table of Contents Xiv 1List of Figures CIE 1931 Chromaticity Diagram This Manual 1IntroductionAbout This Manual If you need Turn to Using This ManualDescription, Features and Benefits Optional Accessories Vision 65/75 Front/Side/Top View Vision 65/75 at a GlanceTemp LED POWER/STANDBY LED Indicates power status as followsVision 65/75 Rear/Bottom/Side View Cable Access Door Open to access connectorsVision 65/75 Rear Panel Hdmi 2 Digital Comp 1 RCA connectorsComp 2 / RGB Vision 65/75 Remote ControlVolt 250 mA Trigger Output 3.5-mm, mini phono jack Source Selection Buttons On / OFFVID S-Video Cursor KeysMemory Preset Buttons Picture Adjustment Buttons BRT BrightnessContrast COL ColorLens Picture-In-Picture PIP ControlsOperation 3InstallationRemote Control Installation Overview Quick SetupStep Procedure For Details, Refer to If installing a CineWide-equipped projector InstallProjector Installation Options Installation ConsiderationsInstallation Type Advantages ConsiderationsProjector Model Throw Ratios for the Vision 65/75 SeriesThrow Range Throw Ratio Vertical and Horizontal Position Ceiling InstallationFloor Installation Up/down vertical lens shift percentages Fixed CineWide Base Plate Cylindrical Lens Installing the Optional CineWide Lens MountMotor AutoScope motor assemblyVision 65/75 with Ceiling Mount Adapters/Projector Stands AutoScope Lens Motor Installation Install Lens MotorDo not OVER-TIGHTEN the Screws Base Plate Prismatic LensVision 65/CineWide or Vision 75/CineWide Floor Mounting Upright Mounting the Vision 65/75Height or Projection Angle Adjusting the ProjectorUsing the On-Screen Menus on 65/75 Connecting SourceConnections to the Vision 65/75 11. RGB Connections 13. Composite, S-Video and Component Video Connections 14. RS-232 Control System Connection ConnectionAutoScope Lens Motor Rear 16. Connecting the 12-Volt Trigger Output to Other EquipmentPower source Turning on the PowerPrimary Lens Adjustments Changing the OSD Language Adjusting the Picture OrientationZoom Zo om Out FocusInstalling and Adjusting the CineWide Anamorphic Lens These instructions 18. Attaching the Anamorphic Lens to the Lens Adapter Ring Attach Lens Mounting Assembly to Lens Motor Carriage PlateAdjusting the Horizontal X Lens Position Installation Anamorphic Lens Top View Adjusting the GeometryWhitney Prismatic AdjustmentAdjusting the Lens Height Y Anamorphic Lens Top View 4Operation Selecting an Aspect Ratio Adjusting the PictureSelecting Video Memory Selecting An Input SourceUsing the On-Screen Menus Using Picture-In-Picture PIPPicture Adjust SetupInstallation Source SelectSource Select Picture AdjustPerform the adjustments in the order listed here Typical Pluge Pattern for Adjusting Brightness You must enter a passcode to access the ISF menuTypical Gray Bar Pattern for Adjusting Contrast Gray Yellow Cyan Green Magenta Red Blue Typical Test Pattern for Adjusting Sharpness Description Aspect Ratio SettingsAspect Ratio Cinema Fit a 2.351 screen InstallationVertical Keystone Correction Horizontal Keystone CorrectionPincushion Correction Operation Information SetupRefer to the instructions for your computer This menu should be used by ISF-certified technicians only Is powered off, then on againSettings reduce the image brightness CIE 1931 Chromaticity Diagram Operation Lamp assembly for replacement 5Maintenance and TroubleshootingLamp Replacement Symptom Possible Causes Solution Troubleshooting TipsTroubleshooting Chart Troubleshooting Chart Maintenance and Troubleshooting RS-232 Connection and Port Configuration Serial Command SyntaxSerial Commands 6Serial CommunicationsSerial Communications Serial Commands Serial Communications Vision 65/75 Specifications 7SpecificationsHome Theater Calibration Specifications Vision Specifications Vision Model 75 SeriesIndustry-Standard Specifications Vision Model 65 Series Industry-Standard Specifications Vision Model 75 SeriesDimensions Power RequirementsWeight without lens Limited WarrantyVision 65/75 Dimensions with Optional Fixed Anamorphic Lens Vision 65/75 DimensionsMHz Supported Signal Timings Supported TimingsFormat Resolution Format Resolution Refresh Rate Hz Horizontal Pixel Frequency Supported Signal TimingsSdtv Signals Video / S-Video Specifications Page 020-0715-02 Rev. a March