Vidikron Vision 75, Vision 65 operation manual These instructions

Page 51

 

Installation

 

 

The Cylindrical Anamorphic lens mount kit consists of everything shown in Figure 3-17.

Cylindrical Anamorphic Lens

Some components shipped with your projector may differ slightly from what is shown in

Installation and Adjustment

these instructions.

 

1Lens Adapter Ring and Mounting Screws (3x)

10 Anamorphic Lens

Set Screw

9 Pitch Adjustment

T-Nut (2x)

2 Pitch Adjustment Yoke for Lens

3 Height/Y Adjustment

T-Screw and Washer

(2x)

4 Pitch Adjustment

T-Screw and

Washer (2x)

5 Anamorphic Lens

Holder

8 Yaw/X Adjustment

Lever (2x)

6 1/4-20 Hex Bolt (2x)

and Washer (2x)

7 AutoScope Carriage Plate or Fixed CineWide Base Plate

Figure 3-17. Cylindrical Anamorphic Lens Mounting Assembly - Exploded View

Vidikron Vision Model 65/Model 75 Installation/Operation Manual

35

Image 51
Contents 65/75 Page TWO Year Limited Warranty RIGHTS, Limits and Exclusions Product Information Retain for Your Records Important Safety Instructions Declaration of Conformity Compliance InformationFCC Part Table of Hazardous Substances Model Name Vision Model 75 Series 1Table of Contents Operation Maintenance and TroubleshootingSerial Communications Table of Contents Xiv 1List of Figures CIE 1931 Chromaticity Diagram 1Introduction About This ManualThis Manual If you need Turn to Using This ManualDescription, Features and Benefits Optional Accessories Vision 65/75 Front/Side/Top View Vision 65/75 at a GlanceTemp LED POWER/STANDBY LED Indicates power status as followsVision 65/75 Rear/Bottom/Side View Cable Access Door Open to access connectorsVision 65/75 Rear Panel Hdmi 2 Digital Comp 1 RCA connectorsVision 65/75 Remote Control Volt 250 mA Trigger Output 3.5-mm, mini phono jackComp 2 / RGB Cursor Keys On / OFFSource Selection Buttons VID S-VideoCOL Color Picture Adjustment Buttons BRT BrightnessMemory Preset Buttons ContrastLens Picture-In-Picture PIP Controls3Installation Remote ControlOperation If installing a CineWide-equipped projector Install Quick SetupInstallation Overview Step Procedure For Details, Refer toAdvantages Considerations Installation ConsiderationsProjector Installation Options Installation TypeThrow Ratios for the Vision 65/75 Series Throw Range Throw RatioProjector Model Ceiling Installation Floor InstallationVertical and Horizontal Position Up/down vertical lens shift percentages Fixed CineWide Base Plate Cylindrical Lens Installing the Optional CineWide Lens MountMotor AutoScope motor assemblyVision 65/75 with Ceiling Mount Adapters/Projector Stands AutoScope Lens Motor Installation Install Lens MotorDo not OVER-TIGHTEN the Screws Base Plate Prismatic LensVision 65/CineWide or Vision 75/CineWide Floor Mounting Upright Mounting the Vision 65/75Adjusting the Projector Using the On-Screen Menus onHeight or Projection Angle Connecting Source Connections to the Vision 65/7565/75 11. RGB Connections 13. Composite, S-Video and Component Video Connections 14. RS-232 Control System Connection ConnectionAutoScope Lens Motor Rear 16. Connecting the 12-Volt Trigger Output to Other EquipmentPower source Turning on the PowerZo om Out Focus Changing the OSD Language Adjusting the Picture OrientationPrimary Lens Adjustments ZoomInstalling and Adjusting the CineWide Anamorphic Lens These instructions 18. Attaching the Anamorphic Lens to the Lens Adapter Ring Attach Lens Mounting Assembly to Lens Motor Carriage PlateAdjusting the Horizontal X Lens Position Installation Anamorphic Lens Top View Adjusting the GeometryWhitney Prismatic AdjustmentAdjusting the Lens Height Y Anamorphic Lens Top View Selecting An Input Source Selecting an Aspect Ratio Adjusting the Picture4Operation Selecting Video MemoryUsing the On-Screen Menus Using Picture-In-Picture PIPSource Select SetupPicture Adjust InstallationPicture Adjust Perform the adjustments in the order listed hereSource Select Typical Pluge Pattern for Adjusting Brightness You must enter a passcode to access the ISF menuTypical Gray Bar Pattern for Adjusting Contrast Gray Yellow Cyan Green Magenta Red Blue Typical Test Pattern for Adjusting Sharpness Aspect Ratio Settings Aspect RatioDescription Cinema Fit a 2.351 screen InstallationVertical Keystone Correction Horizontal Keystone CorrectionPincushion Correction Operation Information SetupRefer to the instructions for your computer This menu should be used by ISF-certified technicians only Is powered off, then on againSettings reduce the image brightness CIE 1931 Chromaticity Diagram Operation 5Maintenance and Troubleshooting Lamp ReplacementLamp assembly for replacement Troubleshooting Tips Troubleshooting ChartSymptom Possible Causes Solution Troubleshooting Chart Maintenance and Troubleshooting 6Serial Communications Serial Command SyntaxRS-232 Connection and Port Configuration Serial CommandsSerial Communications Serial Commands Serial Communications Vision 65/75 Specifications 7SpecificationsIndustry-Standard Specifications Vision Model 75 Series Specifications Vision Model 75 SeriesHome Theater Calibration Specifications Vision Industry-Standard Specifications Vision Model 65 SeriesLimited Warranty Power RequirementsDimensions Weight without lensVision 65/75 Dimensions with Optional Fixed Anamorphic Lens Vision 65/75 DimensionsSupported Signal Timings Supported Timings Format ResolutionMHz Format Resolution Refresh Rate Hz Horizontal Pixel Frequency Supported Signal TimingsSdtv Signals Video / S-Video Specifications Page 020-0715-02 Rev. a March