Vidikron Vision 75, Vision 65 operation manual Anamorphic Lens Top View, Adjusting the Geometry

Page 55

Installation

Adjusting the Yaw: Loosen the Yaw/X-Adjustment Levers to allow the lens to pivot freely from side to side. Then, angle the lens to even out any left-right pincushion distortion:

Anamorphic Lens (Top View)

Correct Position

Wrong Position

Once the proper lens angle has been set, firmly tighten the Yaw/X-Adjustment Levers to secure the lens in place.

Adjusting the Geometry:

1.Input an anamorphic cross-hatch test pattern to the projector.

2.Unscrew the Anamorphic Lens just enough to allow it to rotate freely.

3.Grasp the lens by the center ring and rotate the lens until the image is properly anamorphic:

Wrong Position

Correct Position

4.When the image geometry appears correct, tighten the Anamorphic Lens Set Screw (item #10) to secure the lens in place. (When viewed from the front, the rear opening on the anamorphic lens should appear as a tall, narrow oval.)

Vidikron Vision Model 65/Model 75 Installation/Operation Manual

39

Image 55

Contents 65/75 Page TWO Year Limited Warranty RIGHTS, Limits and Exclusions Product Information Retain for Your Records Important Safety Instructions Declaration of Conformity Compliance InformationFCC Part Table of Hazardous Substances Model Name Vision Model 75 Series 1Table of Contents Operation Maintenance and TroubleshootingSerial Communications Table of Contents Xiv 1List of Figures CIE 1931 Chromaticity Diagram About This Manual 1IntroductionThis Manual If you need Turn to Using This ManualDescription, Features and Benefits Optional Accessories Vision 65/75 Front/Side/Top View Vision 65/75 at a GlanceTemp LED POWER/STANDBY LED Indicates power status as followsVision 65/75 Rear/Bottom/Side View Cable Access Door Open to access connectorsVision 65/75 Rear Panel Hdmi 2 Digital Comp 1 RCA connectorsVolt 250 mA Trigger Output 3.5-mm, mini phono jack Vision 65/75 Remote ControlComp 2 / RGB Cursor Keys On / OFFSource Selection Buttons VID S-VideoCOL Color Picture Adjustment Buttons BRT BrightnessMemory Preset Buttons ContrastLens Picture-In-Picture PIP ControlsRemote Control 3InstallationOperation If installing a CineWide-equipped projector Install Quick SetupInstallation Overview Step Procedure For Details, Refer toAdvantages Considerations Installation ConsiderationsProjector Installation Options Installation TypeThrow Range Throw Ratio Throw Ratios for the Vision 65/75 SeriesProjector Model Floor Installation Ceiling InstallationVertical and Horizontal Position Up/down vertical lens shift percentages Fixed CineWide Base Plate Cylindrical Lens Installing the Optional CineWide Lens MountMotor AutoScope motor assemblyVision 65/75 with Ceiling Mount Adapters/Projector Stands AutoScope Lens Motor Installation Install Lens MotorDo not OVER-TIGHTEN the Screws Base Plate Prismatic LensVision 65/CineWide or Vision 75/CineWide Floor Mounting Upright Mounting the Vision 65/75Using the On-Screen Menus on Adjusting the ProjectorHeight or Projection Angle Connections to the Vision 65/75 Connecting Source65/75 11. RGB Connections 13. Composite, S-Video and Component Video Connections 14. RS-232 Control System Connection ConnectionAutoScope Lens Motor Rear 16. Connecting the 12-Volt Trigger Output to Other EquipmentPower source Turning on the PowerZo om Out Focus Changing the OSD Language Adjusting the Picture OrientationPrimary Lens Adjustments ZoomInstalling and Adjusting the CineWide Anamorphic Lens These instructions 18. Attaching the Anamorphic Lens to the Lens Adapter Ring Attach Lens Mounting Assembly to Lens Motor Carriage PlateAdjusting the Horizontal X Lens Position Installation Anamorphic Lens Top View Adjusting the GeometryWhitney Prismatic AdjustmentAdjusting the Lens Height Y Anamorphic Lens Top View Selecting An Input Source Selecting an Aspect Ratio Adjusting the Picture4Operation Selecting Video MemoryUsing the On-Screen Menus Using Picture-In-Picture PIPSource Select SetupPicture Adjust InstallationPerform the adjustments in the order listed here Picture AdjustSource Select Typical Pluge Pattern for Adjusting Brightness You must enter a passcode to access the ISF menuTypical Gray Bar Pattern for Adjusting Contrast Gray Yellow Cyan Green Magenta Red Blue Typical Test Pattern for Adjusting Sharpness Aspect Ratio Aspect Ratio SettingsDescription Cinema Fit a 2.351 screen InstallationVertical Keystone Correction Horizontal Keystone CorrectionPincushion Correction Operation Information SetupRefer to the instructions for your computer This menu should be used by ISF-certified technicians only Is powered off, then on againSettings reduce the image brightness CIE 1931 Chromaticity Diagram Operation Lamp Replacement 5Maintenance and TroubleshootingLamp assembly for replacement Troubleshooting Chart Troubleshooting TipsSymptom Possible Causes Solution Troubleshooting Chart Maintenance and Troubleshooting 6Serial Communications Serial Command SyntaxRS-232 Connection and Port Configuration Serial CommandsSerial Communications Serial Commands Serial Communications Vision 65/75 Specifications 7SpecificationsIndustry-Standard Specifications Vision Model 75 Series Specifications Vision Model 75 SeriesHome Theater Calibration Specifications Vision Industry-Standard Specifications Vision Model 65 SeriesLimited Warranty Power RequirementsDimensions Weight without lensVision 65/75 Dimensions with Optional Fixed Anamorphic Lens Vision 65/75 DimensionsFormat Resolution Supported Signal Timings Supported TimingsMHz Format Resolution Refresh Rate Hz Horizontal Pixel Frequency Supported Signal TimingsSdtv Signals Video / S-Video Specifications Page 020-0715-02 Rev. a March