Runco XP-50, XP-65 operation manual Installation, Remote Control, Other surfaces

Page 25

3. Installation

To install batteries in the remote control:

1.Press on the tab on the battery compartment cover and lift the cover in the direction of the arrow.

2.Insert the included batteries. Ensure that the polarities correctly match the and markings inside the battery compartment.

3.Close the battery compartment cover and press the tab on the cover until it clicks in place.

1

2

3

“AA” size

-

+	+
	-

3.1

Remote Control

• When installing batteries, make sure that the battery polarities are correct.

Notes on Batteries

•Do not mix an old battery with a new one or different types of batteries.

•If you will not use the remote control for a long time, remove the batteries to avoid damage from battery leakage.

•Do not drop the remote control or expose it to moisture or high temperature.

•The remote control may malfunction under a fluorescent lamp. If that occurs, move the plasma display away from the fluorescent lamp.

•Make sure that there is nothing obstructing the infrared beam between the remote control and the IR receiver on the plasma display.

Note	The signal from the remote control can be reflected by walls or
	other surfaces.

•If the effective range of the remote control decreases, or it stops working, replace the batteries with new ones.

•Ambient conditions may possibly impede the operation of the remote control. If this happens, point the remote control at the plasma display and repeat the operation.

CinemaWall XP-50/XP-65 Installation/Operation Manual

11

Image 25

Contents XP-50 XP-65 Page RuncoCare Standard Features RuncoCare Standard Two Year Limited WarrantyRuncoCare Claim Procedure Page Copyright and Trademarks Important Safety Instructions Declaration of Conformity Compliance InformationFCC Part Page Table of Contents Specifications Maintenance and TroubleshootingAppendix A. Default Settings OperationList of Figures List of Figures Xiv About This Manual IntroductionCertain features Using This ManualSignificance. They also provide supplemental information Degrade performance or cause a malfunctionKey Features and Benefits Description, Features and BenefitsOptional Accessories XP-50 Controls and Functions Controls and IndicatorsCinemaWall at a Glance Display Stand XP-506 XP-65 ConnectorsPower Input Surround button CinemaWall Remote ControlControls and Functions Remote Control InstallationOther surfaces Installation specialist Quick SetupStep Procedure For Details, refer to Installation Considerations Ventilation Ambient LightOther Considerations Connections to Connecting SourceCinemaWall Components toRCA-BNC adapter plug Analog RGB Connections Connector Pin Assignments Connecting External Speakers OptionalRS-232 Controller ConnectionAC Power Connection Setting the Day and Time Turning on the Power Changing the OSD LanguageOperation Setting the Computer Display Properties Aspect ratio selection is saved independently for each input Selecting an Input Source Changing the Aspect Ratio149 169Source image horizon 43 431 linearly scalesPlayed at the left and right Edges of the screenActivating PIP Swapping the Main PIP Images Using Picture-In-Picture PIPSelecting a PIP Target Using the On-Screen MenusScreen or Input Source Changing the PIP Window PositionPOS./SIZE Options Picture This control is not available when Picture Menu is set to Typical Pluge Pattern for Adjusting Brightness Gray Yellow Cyan Green Magenta Red Blue Typical Test Pattern for Adjusting Sharpness POS./SIZE CinemaWall memorizes position and size settings separatelyFrequency is 108 MHz or greater Options menu refer to page 50 is set to OnSound Or 1080p and the Aspect Ratio is set to 169 refer toSET UP Signal Screensaver Is active On the remote control unit, or cycle power to the CinemaWall Order to activate multi-display mode, you must first set Refer to Changing the OSD Language onOn hides joints between displays C D Insert cannot be used when Transparency is set to on Transparency cannot be used when Insert is set to onPresent Time Setup Refer to Setting the Day and Time on Command Timer refer toDVD3 Operation Refer to Return ChangeCurrently active Level see belowSome cases, power is transmitted to the slot when When using multiple displays such as in a video wall RuncoMULTI-DISPLAY is active Picture menu is set to WarmDuring the delay period, the power indicator flashes green Using Digital ZoomOn page 21, the Clock Display setting has no effect Operation Cleaning Maintenance and TroubleshootingCleaning the Display Panel Body and Remote Control Cleaning the ScreenSymptom Possible Causes Solution Troubleshooting TipsCommand 3 bytes Parameter 6 bytes Command 3 bytes Parameter 3 bytesSerial Communications ExamplesHex Description Serial CommandsDwaovlon OSPSCR0 CinemaWall Specifications SpecificationsCinemaWall Model XP-50 Dimensions with Optional Table Stand CinemaWall DimensionsCinemaWall Model XP-65 Dimensions with Optional Table Stand Supported Timings Supported Signal Timings by Input Specifications Table A-1. Runco Factory Default Settings for CinemaWall Appendix A. Default SettingsDefault Settings Page 020-0970-00 Rev. B March