Runco XP-50, XP-65 operation manual Refer to Changing the OSD Language on

Page 55

Operation

POWER SAVE: Select POWER SAVE from the SET UP menu and set it to ON to reduce the overall image intensity by a small amount, thereby reducing power consumption.

STANDBY SAVE: Select STANDBY SAVE from the SET UP menu and set it to ON to minimize power consumption during standby mode.

POWER MANAGEMENT: Select POWER MANAGEMENT from the SET UP menu and set it to ON to activate the power management function for the PC INPUT. This feature, when enabled, operates as follows:

•When no video or sync signals are detected on the PC INPUT for approximately 30 seconds, the power is turned off (standby) and the power indicator lights orange.

•When a signal is subsequently detected, power is restored and the power indicator lights green.

AUTO POWER OFF: Select AUTO POWER OFF from the SET UP menu and set it to ON to have the CinemaWall power itself off after 10 minutes when no signal is present on the

PC INPUT.

Note

OSD LANGUAGE:

POWER MANAGEMENT and AUTO POWER OFF operate only on the PC INPUT and only under the following conditions:

•SYNC is set to AUTO.

•COMPONENT/RGB IN SELECT is set to RGB.

•MULTI PIP is off.

Refer to Changing the OSD Language on page 21.

MULTI DISPLAY SETUP: You can create a video wall consisting of up to 25 (5x5) CinemaWall displays and display an enlarged image across all of them. To do this, select MULTI DISPLAY SETUP from the SET UP menu and press the ACTION () button. Then, configure each display in the video wall as follows:

•MULTI DISPLAY SETUP: Select MULTI DISPLAY SETUP from the MULTI DISPLAY SETUP menu, the set it to ON to activate multi-display mode.

In order to activate multi-display mode, you must first set the

Note MULTI-PIP DISPLAY MODE to “-” (normal). Refer to DISPLAY MODE on page 43.

•HORIZONTAL SCALE: Select HORIZONTAL SCALE from the MULTI DISPLAY SETUP menu to specify the number of displays in each row of the video wall.

•VERTICAL SCALE: Select VERTICAL SCALE from the MULTI DISPLAY SETUP menu to specify the number of displays in each column of the video wall.

CinemaWall XP-50/XP-65 Installation/Operation Manual

41

Image 55

Contents XP-50 XP-65 Page RuncoCare Standard Features RuncoCare Standard Two Year Limited WarrantyRuncoCare Claim Procedure Page Copyright and Trademarks Important Safety Instructions Declaration of Conformity Compliance InformationFCC Part Page Table of Contents Operation Maintenance and TroubleshootingSpecifications Appendix A. Default SettingsList of Figures List of Figures Xiv About This Manual IntroductionDegrade performance or cause a malfunction Using This ManualCertain features Significance. They also provide supplemental informationKey Features and Benefits Description, Features and BenefitsOptional Accessories XP-50 Controls and Functions Controls and IndicatorsCinemaWall at a Glance Display Stand XP-506 XP-65 ConnectorsPower Input Surround button CinemaWall Remote ControlControls and Functions Remote Control InstallationOther surfaces Installation specialist Quick SetupStep Procedure For Details, refer to Installation Considerations Ventilation Ambient LightOther Considerations Components to Connecting SourceConnections to CinemaWallRCA-BNC adapter plug Analog RGB Connections Connection Connecting External Speakers OptionalConnector Pin Assignments RS-232 ControllerAC Power Connection Setting the Day and Time Turning on the Power Changing the OSD LanguageOperation Setting the Computer Display Properties Aspect ratio selection is saved independently for each input Selecting an Input Source Changing the Aspect Ratio149 169Edges of the screen 43 431 linearly scalesSource image horizon Played at the left and rightActivating PIP Swapping the Main PIP Images Using Picture-In-Picture PIPChanging the PIP Window Position Using the On-Screen MenusSelecting a PIP Target Screen or Input SourcePOS./SIZE Options Picture This control is not available when Picture Menu is set to Typical Pluge Pattern for Adjusting Brightness Gray Yellow Cyan Green Magenta Red Blue Typical Test Pattern for Adjusting Sharpness POS./SIZE CinemaWall memorizes position and size settings separatelyFrequency is 108 MHz or greater Options menu refer to page 50 is set to OnSound Or 1080p and the Aspect Ratio is set to 169 refer to SET UP Signal Screensaver Is active On the remote control unit, or cycle power to the CinemaWall Order to activate multi-display mode, you must first set Refer to Changing the OSD Language onOn hides joints between displays C D Insert cannot be used when Transparency is set to on Transparency cannot be used when Insert is set to onPresent Time Setup Refer to Setting the Day and Time on Command Timer refer toDVD3 Operation Refer to Return ChangeCurrently active Level see belowPicture menu is set to Warm When using multiple displays such as in a video wall RuncoSome cases, power is transmitted to the slot when MULTI-DISPLAY is activeDuring the delay period, the power indicator flashes green Using Digital ZoomOn page 21, the Clock Display setting has no effect Operation Cleaning the Screen Maintenance and TroubleshootingCleaning Cleaning the Display Panel Body and Remote ControlSymptom Possible Causes Solution Troubleshooting TipsExamples Command 3 bytes Parameter 3 bytesCommand 3 bytes Parameter 6 bytes Serial CommunicationsHex Description Serial CommandsDwaovlon OSPSCR0 CinemaWall Specifications SpecificationsCinemaWall Model XP-50 Dimensions with Optional Table Stand CinemaWall DimensionsCinemaWall Model XP-65 Dimensions with Optional Table Stand Supported Timings Supported Signal Timings by Input Specifications Table A-1. Runco Factory Default Settings for CinemaWall Appendix A. Default SettingsDefault Settings Page 020-0970-00 Rev. B March