Runco XP-50 Command Timer refer to, Present Time Setup Refer to Setting the Day and Time on

Page 59

Operation

PORTRAIT SETUP: You can create a video wall consisting of three (3x1) CinemaWall displays in “portrait” mode and display an enlarged image across all of them.

1

2

3

To do this, select PORTRAIT SETUP from the SET UP menu and press the ACTION () button. Then, configure each display in the video wall as follows:

•PORTRAIT SETUP: Select PORTRAIT SETUP from the PORTRAIT SETUP menu, the set it to ON to activate portrait mode.

In order to activate portrait mode, you must first set the MULTI-PIP

Note DISPLAY MODE to “-” (normal). Refer to DISPLAY MODE on page 43.

•SEAM HIDES VIDEO: Refer to SEAM HIDES VIDEO on page 42.

•VIEWING AREA: If you are displaying SD images with a 4:3 aspect ratio in portrait mode, select VIEWING AREA from the PORTRAIT SETUP menu and set it to 4:3.

•LOCATION: Select LOCATION from the PORTRAIT SETUP menu to specify the CinemaWall’s position in the video wall. This determines which segment of the enlarged image this panel will display. Select 1 for the left portion of the image, 2 for the center portion or 3 for the right portion.

•AI SYNCHRONIZATION: Refer to AI SYNCHRONIZATION on page 42.

SET UP TIMER: To program the CinemaWall to turn on and/or off at specific times each day, select SET UP TIMER from the SET UP menu and press the ACTION () button.

Note	You cannot use the SET UP TIMER if you enable the Weekly
	Command Timer (refer to page 47).

•POWER ON FUNCTION/POWER ON TIME: To enable automatic, time-of-day power on, set POWER ON FUNCTION to ON. Then, press to select POWER ON TIME.

Press or to change the POWER ON TIME in one-minute increments. Press and hold or to change the POWER ON TIME in 15-minute increments.

•POWER OFF FUNCTION/POWER OFF TIME: To enable automatic, time-of-day shutdown, set POWER OFF FUNCTION to ON. Then, press to select POWER OFF TIME.

Press or to change the POWER OFF TIME in one-minute increments. Press and hold or to change the POWER OFF TIME in 15-minute increments.

PRESENT TIME SETUP: Refer to Setting the Day and Time on page 21.

CinemaWall XP-50/XP-65 Installation/Operation Manual

45

Image 59

Contents XP-50 XP-65 Page RuncoCare Standard Features RuncoCare Standard Two Year Limited WarrantyRuncoCare Claim Procedure Page Copyright and Trademarks Important Safety Instructions Declaration of Conformity Compliance InformationFCC Part Page Table of Contents Operation Maintenance and TroubleshootingSpecifications Appendix A. Default SettingsList of Figures List of Figures Xiv About This Manual IntroductionDegrade performance or cause a malfunction Using This ManualCertain features Significance. They also provide supplemental informationKey Features and Benefits Description, Features and BenefitsOptional Accessories XP-50 CinemaWall at a Glance Controls and IndicatorsControls and Functions Display Stand XP-506 XP-65 ConnectorsPower Input Surround button CinemaWall Remote ControlControls and Functions Other surfaces InstallationRemote Control Step Procedure For Details, refer to Quick SetupInstallation specialist Installation Considerations Ventilation Ambient LightOther Considerations Components to Connecting SourceConnections to CinemaWallRCA-BNC adapter plug Analog RGB Connections Connection Connecting External Speakers OptionalConnector Pin Assignments RS-232 ControllerAC Power Connection Operation Turning on the Power Changing the OSD LanguageSetting the Day and Time Setting the Computer Display Properties Aspect ratio selection is saved independently for each input Selecting an Input Source Changing the Aspect Ratio149 169Edges of the screen 43 431 linearly scalesSource image horizon Played at the left and rightActivating PIP Swapping the Main PIP Images Using Picture-In-Picture PIPChanging the PIP Window Position Using the On-Screen MenusSelecting a PIP Target Screen or Input SourcePOS./SIZE Options Picture This control is not available when Picture Menu is set to Typical Pluge Pattern for Adjusting Brightness Gray Yellow Cyan Green Magenta Red Blue Typical Test Pattern for Adjusting Sharpness POS./SIZE CinemaWall memorizes position and size settings separatelyFrequency is 108 MHz or greater Options menu refer to page 50 is set to OnSound Or 1080p and the Aspect Ratio is set to 169 refer toSET UP Signal Screensaver Is active On the remote control unit, or cycle power to the CinemaWall Order to activate multi-display mode, you must first set Refer to Changing the OSD Language on On hides joints between displays C D Insert cannot be used when Transparency is set to on Transparency cannot be used when Insert is set to onPresent Time Setup Refer to Setting the Day and Time on Command Timer refer toDVD3 Operation Refer to Return ChangeCurrently active Level see belowPicture menu is set to Warm When using multiple displays such as in a video wall RuncoSome cases, power is transmitted to the slot when MULTI-DISPLAY is activeOn page 21, the Clock Display setting has no effect Using Digital ZoomDuring the delay period, the power indicator flashes green Operation Cleaning the Screen Maintenance and TroubleshootingCleaning Cleaning the Display Panel Body and Remote ControlSymptom Possible Causes Solution Troubleshooting TipsExamples Command 3 bytes Parameter 3 bytesCommand 3 bytes Parameter 6 bytes Serial CommunicationsHex Description Serial CommandsDwaovlon OSPSCR0 CinemaWall Specifications SpecificationsCinemaWall Model XP-50 Dimensions with Optional Table Stand CinemaWall DimensionsCinemaWall Model XP-65 Dimensions with Optional Table Stand Supported Timings Supported Signal Timings by Input Specifications Table A-1. Runco Factory Default Settings for CinemaWall Appendix A. Default SettingsDefault Settings Page 020-0970-00 Rev. B March