Runco XP-65, XP-50 operation manual Transparency cannot be used when Insert is set to on

Page 58

Operation

•TRANSPARENCY/TRANSPARENCY LEVEL: If you are using the Blend PIP feature, you can make the overlay (sub) image transparent so that the main (background) image shows through.

To do this, select TRANSPARENCY from the MULTI PIP SETUP menu and set it to ON. Then, select TRANSPARENCY LEVEL from the MULTI PIP SETUP menu to control the degree to which you want the main image to show through.

TRANSPARENCY = 0% TRANSPARENCY = 50% TRANSPARENCY = 90%

A B C D A B C D A B C D

TRANSPARENCY cannot be used when INSERT is set to ON.

Note

•INSERT/INSERT LEVEL: If you are using the Blend PIP feature, you can divide the overlay (sub) image into transparent and non-transparent areas. The CinemaWall then “inserts” only the non-transparent areas of the overlay image into the main (background) image.

To use this feature, select INSERT from the MULTI PIP SETUP menu and set it to ON. Then, select INSERT LEVEL from the MULTI PIP SETUP menu to set the brightness level threshold for distinguishing between the transparent and non-transparent areas of the overlay image.

INSERT LEVEL = 1%

A B C D

INSERT LEVEL = 5%

A B C D

INSERT LEVEL = 10%

A B C

INSERT cannot be used when TRANSPARENCY is set to ON.

Note

44	CinemaWall XP-50/XP-65 Installation/Operation Manual

Image 58

Contents XP-50 XP-65 Page RuncoCare Standard Two Year Limited Warranty RuncoCare Standard FeaturesRuncoCare Claim Procedure Page Copyright and Trademarks Important Safety Instructions Compliance Information Declaration of ConformityFCC Part Page Table of Contents Appendix A. Default Settings Maintenance and TroubleshootingSpecifications OperationList of Figures List of Figures Xiv Introduction About This ManualSignificance. They also provide supplemental information Using This ManualCertain features Degrade performance or cause a malfunctionDescription, Features and Benefits Key Features and BenefitsOptional Accessories XP-50 Controls and Functions Controls and IndicatorsCinemaWall at a Glance Display Stand Connectors XP-506 XP-65Power Input CinemaWall Remote Control Surround buttonControls and Functions Remote Control InstallationOther surfaces Installation specialist Quick SetupStep Procedure For Details, refer to Installation Considerations Ambient Light VentilationOther Considerations CinemaWall Connecting SourceConnections to Components toRCA-BNC adapter plug Analog RGB Connections RS-232 Controller Connecting External Speakers OptionalConnector Pin Assignments ConnectionAC Power Connection Setting the Day and Time Turning on the Power Changing the OSD LanguageOperation Setting the Computer Display Properties Selecting an Input Source Changing the Aspect Ratio Aspect ratio selection is saved independently for each input169 149Played at the left and right 43 431 linearly scalesSource image horizon Edges of the screenUsing Picture-In-Picture PIP Activating PIP Swapping the Main PIP ImagesScreen or Input Source Using the On-Screen MenusSelecting a PIP Target Changing the PIP Window PositionPOS./SIZE Options Picture This control is not available when Picture Menu is set to Typical Pluge Pattern for Adjusting Brightness Gray Yellow Cyan Green Magenta Red Blue Typical Test Pattern for Adjusting Sharpness CinemaWall memorizes position and size settings separately POS./SIZEOptions menu refer to page 50 is set to On Frequency is 108 MHz or greaterOr 1080p and the Aspect Ratio is set to 169 refer to SoundSET UP Signal Screensaver Is active On the remote control unit, or cycle power to the CinemaWall Refer to Changing the OSD Language on Order to activate multi-display mode, you must first setOn hides joints between displays C D Transparency cannot be used when Insert is set to on Insert cannot be used when Transparency is set to onCommand Timer refer to Present Time Setup Refer to Setting the Day and Time onDVD3 Operation Return Change Refer toLevel see below Currently activeMULTI-DISPLAY is active When using multiple displays such as in a video wall RuncoSome cases, power is transmitted to the slot when Picture menu is set to WarmDuring the delay period, the power indicator flashes green Using Digital ZoomOn page 21, the Clock Display setting has no effect Operation Cleaning the Display Panel Body and Remote Control Maintenance and TroubleshootingCleaning Cleaning the ScreenTroubleshooting Tips Symptom Possible Causes SolutionSerial Communications Command 3 bytes Parameter 3 bytesCommand 3 bytes Parameter 6 bytes ExamplesSerial Commands Hex DescriptionDwaovlon OSPSCR0 Specifications CinemaWall SpecificationsCinemaWall Dimensions CinemaWall Model XP-50 Dimensions with Optional Table StandCinemaWall Model XP-65 Dimensions with Optional Table Stand Supported Timings Supported Signal Timings by Input Specifications Appendix A. Default Settings Table A-1. Runco Factory Default Settings for CinemaWallDefault Settings Page 020-0970-00 Rev. B March