Sanyo PLV-HD2000E, PLV-HD2000N owner manual Lens Replacement and Installation Procedure

Page 57

LENS REPLACEMENT AND INSTALLATION PROCEDURE

NOTE : The installation procedure and needed parts for lens installation depend on the type of the Projection Lens. Check the Model No. of the Projection Lens and be sure to install or replace the lens following procedure below.

1

Remove Lens Cover. Remove 2 Screws A. Push

part B and pull Upper Lens Cover up.

(See Fig. 1.)

UPPER LENS

COVER

B

2

Remove 4 Screws C. Pull Lower Lens Cover

toward front and remove. (See Fig. 2.)

LOWER LENS

COVER

A

C

C

D

Fig-1

Fig-2

3

Remove 2 Screws D and Cover Plate on the

back of Upper Lens Cover. (See Fig. 3.)

UPPER LENS

COVER

COVER PLATE

Fig-3

- 2 -

Page 56 Page 58
Image 57
Page 56 Page 58
Contents Model PLV-HD2000N/E Risk of Electric Shock Do not Open To the OwnerVoor de klanten in Nederland Safety InstructionsFederal Communication Commission Notice CompliancesTable of Contents Compatibility Features and DesignName of Each Part of Projector PreparationConnecting AC Power Cord SETTING-UP ProjectorPreparation Lens Installation Lens Shift AdjustmentPositioning Projector Installing Projector in Proper Position Preparation Picture Level and Tilt AdjustmentPreparation Moving Projector Connecting Projector Replacement of TerminalTerminals of Projector Input 2 Connecting Projector INPUT/OUTPUT Terminals and Jacks InputSerial Port Terminal Connecting ProjectorCables used for connection Connecting to ComputerConnecting to Video Equipment External Audio EquipmentAudio Amplifier Audio Speaker stereo Before Operation Side Controls and IndicatorsFront Indicators Indicators0WIRED Remote Jack Operation of Remote ControlCode Change Remote Control Batteries InstallationHOW to Operate ON-SCREEN Menu Operating ON-SCREEN MenuFlow of ON-SCREEN Menu Operation System BOX Before Operation Menu BARTurning on / OFF Projector Basic OperationTurning on Projector Turning OFF ProjectorAdjusting Screen Picture Freeze FunctionNo Show Function Direct Operation Selecting Input SourceMenu Operation InputWhen Select Input 2 5 BNC Terminal Automatic MULTI-SCAN System System SelectSystem Menu System Select Menu PCBasic Operation Select Video System System Select Menu SDIAuto Display Adjustments Display AdjustScreen Adjustments Screen Adjustment DirectAuto PC Adj Display Adjust Auto PC AdjustmentDisplay Adjust Manual Display Adjustments Clamp Current modeImage Adjust Menu Image AdjustmentsImage Level Select Direct Image Level Select MenuDisplay Adjust Image Level Adjustments Progressive Noise reductionAuto picture control Auto lamp controlMenu COLOR.MList COLOR.M Menu Color Palette DELGamma balance Closes Image Adjust MenuSetting Setting MenuSetting Menu Logo Menu positionCeiling RearPower management Remote controlOn start Factory default Lamp counter resetKey lock QuitMaintenance AIR Filter Care and CleaningAppendix Appendix Lamp Management Yellow Lamp Dim Lamp Red LampMark on Lamp Front Indicators Rear Indicators Appendix Lamp ReplacementOrder Replacement Lamp Cleaning Projection LensProblem Try these Solutions TroubleshootingService Appendix Indicators and Projector Condition Indicators Projector ConditionMenu Tree Display adjustImage adjust Remote Control Transmitter Technical SpecificationsDVI-I Terminal DIGITAL/ANALOG Appendix Configurations of TerminalsResolution Appendix Compatible Computer SpecificationsOptional Parts Dimensions LCD Projector Lens Replacement and Installation Procedure Fig-4 Fig-8 Fig-9 Focus Adjustment For Model LNS-W03 Correcting the focus MAX Side MAX Model No Zoom 100 120 150 180 200 250 300 350 400 500 600Part No 327 3082 1AA6P1P5055-- MA4A
Top Page Image Contents