Transition Networks DVP 5140K manual Installing Optional Redundant Power Supply Module

Page 14

2.3Installing Optional Redundant Power Supply Module

The standard Multichannel Media Converter is shipped with one MAIN Power Supply Module installed at the back of the Multichannel Media Converter cabinet and with a protective plate covering an installation slot intended for a second, optional BACKUP Power Supply Module.

NOTE: Prior to installation of the optional redundant Power Supply Module, a jumper setting on the Management Module already installed in the Multichannel Media Converter must be changed from the NORMAL position to the B(a)CK(u)P position.

WARNING: DO NOT CONNECT POWER SUPPLY MODULE TO

EXTERNAL POWER BEFORE INSTALLING IN MULTICHANNEL MEDIA

CONVERTER. FAILURE TO OBSERVE THIS WARNING COULD RESULT

IN EQUIPMENT DAMAGE AND/OR PERSONAL INJURY OR DEATH.

CAUTION: Wear a grounding device and observe electrostatic discharge precautions when setting Management Module jumper and when installing Power Supply Module in Multichannel Media Converter. Failure to observe this caution could result in damage to, and subsequent failure of, Management Module and/or Power Supply Module.

NOTE: Power Supply Modules can be “hot swapped”.

2.3.1Setting Management Module Jumper

CAUTION: Failure to set the Management Module NJP1 jumper correctly may result in false alarms (if the jumper is set to BCKP while only one Power Supply Module is installed) or in failure to monitor the redundant power supply (if a second Power Supply Module is installed and the jumper is left in the NORMAL position).

To set the Management Module jumper:

1.Place the Multichannel Media Converter on a clean, stable surface.

2.Locate the Management Module installed at the back left of the Multichannel Media Converter.

3.Carefully remove the Management Module from the Multichannel Media Converter by unscrewing two (2) thumbscrews that secure the Management Module to the Multichannel Media Converter and then gently sliding the Management Module from the Multichannel Media Converter.

4.Place the Management Module on flat, stable surface and locate the jumper identified as NJP1.

5.Using a small needle-nosed pliers or similar device, change the 2-position jumper labelled NJP1 from the NORMAL position to the BACKUP position (indicated on Management Module circuit board).

2.4

METTF10XX, MFETF10XX

Page 13 Page 15
Image 14
Page 13 Page 15
Contents Multichannel Media Converter Compliance Information Table of Contents Operation AC Power Supply Module/Optional Redundant AC Power IntroductionMultichannel Media Converter Models Media Converter ChannelsReset Button IntroductionSerial Port Multichannel Media Converter Management ModuleManagement Module LEDs Multiport Management Software at Remote Network RJ-45 ConnectionPage Installation Connecting Channel Ports to NetworkPreparing the Site Installation Unpacking METTF10xx, MFETF10xx EquipmentInstalling Optional Redundant Power Supply Module Setting Management Module JumperInstalling Power Supply Module Installing Multichannel Media Converter at Site Standard Rack InstallationTable-Top Installation Powering the Multichannel Media Converter Setting Full-Duplex/Half-Duplex Configuration Switches Connecting Channel Ports to NetworkSetting FDX/HDX Channel Configuration Switches Testing Fiber Links Installing Fiber-optic CableInstalling Cable Installing Twisted-Pair Copper Cable Norm TestSetting Network Management Parameters NoneEthernet Parameters METTF10xx, MFETF10xx Installing Multiport Management Software at Remote NMS TCP/IPPage Operation Management LEDs Using Status LEDsPower Supply and Link Test Switch LEDs Channel LEDsUsing a Terminal Emulator OperationUsing Terminal Emulator Operation Using Multiport Management Software at Remote NMS Standalone Win32* SystemsMain Power Supply Status is green for OK or red for fail Page Maintenance Fault Isolation and Recovery Is Multichannel Media Converter Receiving Power?Are Channel Links Good? Fault Isolation and Recovery Hardware Replacement Procedures Replacing Management ModuleReplacing AC Power Supply Module Technical Specifications PowerPage Channel Cable Specifications Fiber-Optic CableMETTF1011 -120 MFETF1011

DVP 5140K specifications

Transition Networks DVP 5140K is a robust device tailored for extending Ethernet networks over longer distances. This equipment stands out due to its reliability, high performance, and advanced features, making it a dependable choice for many organizations seeking to enhance their network capabilities.

One of the most notable features of the DVP 5140K is its support for Power over Ethernet (PoE). This technology allows the device to deliver both data and power to connected devices like IP cameras, wireless access points, and VoIP phones via a single Ethernet cable. The DVP 5140K supports various PoE standards, providing flexibility and ensuring compatibility with a wide range of PoE-enabled devices.

The DVP 5140K operates on an advanced switching architecture that allows it to handle a high volume of traffic without compromising performance. Its ability to process data at wire-speed ensures minimal latency and optimal throughput, which is essential for organizations that rely on real-time data transfer for operations. The device supports VLAN tagging, enabling users to create distinct network segments for improved security and performance.

Additionally, the device is designed with robust management features. It includes a web-based graphical user interface (GUI) that simplifies configuration and monitoring tasks. Network administrators can easily manage the device via SNMP (Simple Network Management Protocol), making it compatible with existing network management systems. The DVP 5140K also supports Quality of Service (QoS) settings, ensuring that critical applications receive the necessary bandwidth and prioritization.

Another significant characteristic of the DVP 5140K is its durability and suitability for various environments. The device is built with a metal chassis, providing resilience against physical impacts and environmental factors. It operates effectively in temperatures ranging from -40°C to 70°C, making it ideal for deployment in both indoor and outdoor settings.

In conclusion, Transition Networks DVP 5140K is a versatile and powerful networking solution combining PoE support, high-performance data processing, effective management tools, and durability. These features make it an excellent choice for organizations looking to expand their network infrastructure while ensuring reliability and efficiency in their operations. Whether for enterprise networks, public spaces, or industrial applications, the DVP 5140K meets the demands of modern networking with style and precision.
Top Page Image Contents