Transition Networks DVP 5140K manual Introduction, Reset Button

Page 7

1 INTRODUCTION

1.3

Channel Switches

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Full-duplex/half-duplex mode selection

 

 

 

 

 

 

 

 

 

 

 

 

 

 

switches (DIP switches #1-6) allow the

 

 

 

FDX

 

 

 

 

NORM

 

network administrator to set EACH media 1

 

 

 

 

 

 

 

 

2

3

4

5

6

 

 

 

 

converter channel, separately, either to full-

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

duplex or to half-duplex.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

1

2

3

4

5

6

7

 

 

The Link Test switch (DIP switch #7)

 

 

 

HDX

 

 

 

 

TEST

enables or disables the Missing Link Test feature for a block of six (6) Multichannel Media Converter channels.

1.4Reset Button

Located only on 100BASE-TX MFETF10xx series Multichannel Media Converter models, the Rest button, if present, allows the network administrator to reset ALL Multichannel Media Converter channel ports.

1.5AC Power Supply Module/Optional Redundant AC Power Supply Module

An AC Power Supply Module, installed at the back of the Multichannel

Media Converter before shipment, supplies power to the Multichannel

Media Converter through an external power cord connected to an external

AC outlet.

NOTE: The Multichannel Media Converter does not have an ON/OFF power switch. Power is applied to, and removed from, the Multichannel Media Converter by connecting and disconnecting the power cord.

The Multichannel Media Converter rear panel also contains an expansion slot for an optional redundant Power Supply Module. When installed, the optional redundant Power Supply Module shares the power load with the main AC Power Supply Module. If one power supply fails, the remaining power supply assumes the role of providing all power to the Multichannel Media Converter, thereby protecting the Multichannel Media Converter from a system failure.

NOTE: Both the redundant Power Supply Module and the main AC Power

Supply Module can be "hot swapped".

The MAIN power LED on the front panel of the

100BASE-TX to 100BASE-FX

 

Multichannel Media ConverterLED is a steady amber

M E N T

when thef the AC Power Supply Module is operating

 

 

 

POWER

 

 

 

properly. When the optional redundant Power Supply

 

 

 

BCKP

 

 

 

MAIN

Module is installed and operating properly, the BCKP

 

 

 

 

 

 

TEST

 

 

 

 

 

 

power LED is a steady green.

 

 

 

 

MULTICHANNEL MEDIA CONVERTER

1.3

Image 7
Contents Multichannel Media Converter Compliance Information Table of Contents Operation Introduction AC Power Supply Module/Optional Redundant AC PowerMedia Converter Channels Multichannel Media Converter ModelsIntroduction Reset ButtonManagement Module LEDs Multichannel Media Converter Management ModuleSerial Port Network RJ-45 Connection Multiport Management Software at RemotePage Connecting Channel Ports to Network InstallationPreparing the Site Unpacking METTF10xx, MFETF10xx Equipment InstallationSetting Management Module Jumper Installing Optional Redundant Power Supply ModuleInstalling Power Supply Module Standard Rack Installation Installing Multichannel Media Converter at SiteTable-Top Installation Powering the Multichannel Media Converter Setting FDX/HDX Channel Configuration Switches Connecting Channel Ports to NetworkSetting Full-Duplex/Half-Duplex Configuration Switches Installing Cable Installing Fiber-optic CableTesting Fiber Links Norm Test Installing Twisted-Pair Copper CableNone Setting Network Management ParametersEthernet Parameters METTF10xx, MFETF10xx TCP/IP Installing Multiport Management Software at Remote NMSPage Operation Channel LEDs Using Status LEDsPower Supply and Link Test Switch LEDs Management LEDsOperation Using a Terminal EmulatorUsing Terminal Emulator Operation Standalone Win32* Systems Using Multiport Management Software at Remote NMSMain Power Supply Status is green for OK or red for fail Page Maintenance Is Multichannel Media Converter Receiving Power? Fault Isolation and RecoveryAre Channel Links Good? Fault Isolation and Recovery Replacing Management Module Hardware Replacement ProceduresReplacing AC Power Supply Module Power Technical SpecificationsPage Fiber-Optic Cable Channel Cable SpecificationsMETTF1011 -120 MFETF1011