Speco Technologies CS8, CS4 manual Very High resolution

Page 36

Operation Instruction

NOTE: The total ips of all camera channels will be limited to 120 ips (60 ips for 4-ch Model) when set to High resolution and 60 ips (30 ips for 4-ch Model) when set to Very High resolution.

NOTE: When set to High or Very High resolution, the maximum recording speed of each camera channel might decrease so as not to exceed the total ips of all camera channels. The 8-channel model DVR has two camera groups (No. 1: cameras 1 to 4 and No. 2: cameras 5 to 8), and setting resolution will be applied to all the cameras within the same camera group. See the table below.

No. of cameras set to On and

High resolution

0

1

2

3

4

30 ips

30 ips

20 ips

15 ips

No. of cameras set to On and

Very High resolution

0

1

2

3

4

30 ips

15 ips

10 ips

7.5 ips

Highlight the Event Record Dwell box and set the length of time you would like to record for the associated event. You can set the dwell from 5 seconds to 15 minutes. Refer to Event Actions screen in this chapter for information regarding event recording.

Highlighting Record Audio and pressing the button toggles between On and Off. When set to On, the DVR will record audio when video is recording.

NOTE: The DVR will NOT record audio when the recording speed is set to less than 1 ips.

Highlight the box beside Auto Deletion, and use the Left and Right arrow buttons to adjust the length of time recorded data will be kept from 1 to 999 days. The DVR automatically deletes video recorded earlier than the user-defined period under three conditions: at midnight, whenever the system reboots or whenever the user changes the Auto Deletion settings. Selecting Never will disable the Auto Deletion function.

Highlight the slide bar beside Limit Time-Lapse Recording, and use the Left and Right arrow buttons to adjust the length of the maximum storage time for time-lapse recording from 1 to 99 days. The Limit Time-Lapse Recording feature will function when the storage device has enough space to record video data longer than the preset period. When this feature is On, the DVR records over the oldest “time-lapse” video once all available storage has been used in the Recycle mode, so more event video can be saved. Selecting Never will disable the Limit Time-Lapse Recording function.

NOTE: When the storage device does not have enough space to record video data longer than the preset Limit Time-Lapse Recording period, the DVR records over the oldest video data (time-lapse or event video) as it would in the Recycle mode even if this feature is turned On.

NOTE: The maximum storage time is only an estimate because the amount of space required to store video varies depending on many factors such as motion and image complexity.

Highlight the Panic Record tab, and the Panic Record setup screen appears.

26

Image 36
Contents Page Page Compliance Notice of FCC Weee Waste Electrical & Electronic Equipment Table of Contents Operation Instruction Channel Digital Video Recorder List of Illustrations Vii Operation Instruction Viii Features Technical OverviewTypical DVR installation Package Contents Required Installation ToolsFactory Reset Switch Audio In/OutVideo Out Network PortAlarm Input/Output RS485 PortPower Cord Connector Front Panel Controls Menu ButtonCopy Button Esc ButtonPlay/Stop Button Camera ButtonsRemote Control Buttons Power LEDUSB Port Login/Logout Button ID ButtonSequence Button Playback ButtonsAlarm Button Layout ButtonZoom Button PTZ ButtonTurning on the Power Initial Unit SetupSetup Screen Logout screenSystem Setup InformationChannel Digital Video Recorder Date/Time setup screen Date/TimeHoliday setup screen StorageStorage Information setup screen Storage Status setup screen UserOperation Instruction EZ Setup EZ Setup screenDate/Time Setup Internet Connection LAN Setup Recording Setup ShutdownRecord Very High resolution Panic Record setup screen ScheduleDwell in the Settings column, the DVR Pre-Event Event Setup Alarm-InAlarm-In Actions 1 setup screen Motion Detection Motion Detection Actions 1 setup screen Motion Detection Actions 2 setup screen Video LossVideo Blind DVR checks to see if anything is blinding the camera Text-In Device setup screen Text-InOperation Instruction Text-In Actions setup screen System EventHealth Check setup screen Event Status Network Setup NetworkNetwork setup screen IP Address Gateway Subnet Mask Dvrns setup screen Help Desk Speco Remote setup screen NotificationHighlight the + and press the button to add a mail recipient Notification SNS setup screen Devices Setup CameraHighlight the PTZ tab, and the PTZ setup screen displays Alarm-Out AudioAlarm-Out Schedule setup screen Digital DeterrentOperation Instruction Display OSD setup screen DisplayMain Monitor setup screen Remote Control Remote Control setup screenOperation Instruction Operation Live MonitoringLive Monitoring Menu Display FreezeAlarm SequenceCamera Menu Setup Search ModeLogin/Logout Active Cameo ModeZoom Mode PTZ ModeEvent Monitoring Covert CameraZoom In / Out Recording Video Recording AudioPlaying Recorded Video Searching Video Search menuSearch Menu Display SearchGo To Export Data Source ExitEvent Log Search Operation Instruction Record Table Search Record Table Search screenConfiguration Digital Deterrent section for more details Motion SearchChannel Digital Video Recorder Text-In Search Text-In Search screenClip-Copy Clip-Copy screenOperation Instruction USB Hard Disk Drive Preparation Preparing the USB hard disk drive in WindowsText-In Search Examples Search ExampleSpeco Remote Operation Instruction Web Monitoring Mode Web Search Mode  Change Camera Title Changes the camera nameChannel Digital Video Recorder System Log Notices Error Code Notices TroubleshootingSystem Upgrade Related Clip Copy Related Problem Possible SolutionMap of Screens Specifications VideoGeneral