Speco Technologies CS4, CS8 manual USB Hard Disk Drive Preparation

Page 87

4- & 8-Channel Digital Video Recorder

Appendix

USB Hard Disk Drive Preparation

Preparing the USB hard disk drive in Windows 2000

NOTE: Preparing a USB hard disk drive under Windows XP, Windows Vista and Windows 7 is almost identical to Windows 2000.

1.Connect the USB hard disk drive to your computer using the USB Cable.

2.Turn on your computer.

3.The USB device icon should display on the Taskbar.

4.If the USB hard disk drive is partitioned or has data, it will show up in My Computer as a hard disk drive icon. Check the file system by right clicking on the icon and checking under Properties > General > File System. If the file system is NOT FAT32 format, format the USB hard disk drive using the FAT32 format.

5.If the USB hard disk drive is not partitioned, go to Administrative Tools in Control Panel and launch Computer Management. Open Disk Management in Storage and right click an unallocated region of the USB hard disk drive. Then, click Create Partition.

6.In the Create Partition wizard, click Next then Primary Partition, and follow the instructions on the screen. Make sure that the FAT32 is selected for the file system.

NOTE: The partition size should be less than 32GB because of Microsoft limitations.

After formatting is complete, the USB hard disk drive will be added to My Computer.

7.Connect the USB hard disk drive to the DVR.

Preparing the USB hard disk drive in Windows 98

NOTE: Preparing a USB hard disk drive under Windows ME is almost identical to Windows 98.

1.Connect the USB hard disk drive to your computer using the USB Cable.

2.Turn on your computer. The Add New Hardware wizard window will appear.

3.Install the device driver for the USB backup device following the instructions provided with your USB hard disk drive.

4.If the USB hard disk drive is partitioned or contains data, it will show up in My Computer as a hard disk drive icon. Check the file system in Properties > General > File System. If the file system is NOT FAT32 format, format the USB hard disk drive with FAT32 format.

5.Run the FDISK utility by clicking Start then RUN. Type “fdisk” and click OK.

6.When the MS-DOS command prompt appears, type “Y” and hit the enter key.

7.In the FDISK Option menu, choose “5. Change current fixed disk drive.”

8.Choose the appropriate letter corresponding to the USB hard disk drive.

9.In the FDISK Option menu, choose “1. Create DOS partition or Logical DOS Drive.”

10.In the Create DOS Partition or Logical DOS Drive menu, choose “1. Create Primary DOS Partition.” And Type “Y” to use all available space and hit the enter key. Hit ESC to exit the screen after the USB hard disk drive partition is created.

11.Restart your computer and verify the newly created drive is in My Computer.

77

Image 87
Contents Page Page Compliance Notice of FCC Weee Waste Electrical & Electronic Equipment Table of Contents Operation Instruction Channel Digital Video Recorder List of Illustrations Vii Operation Instruction Viii Technical Overview FeaturesTypical DVR installation Required Installation Tools Package ContentsNetwork Port Factory Reset SwitchAudio In/Out Video OutRS485 Port Alarm Input/OutputPower Cord Connector Menu Button Front Panel ControlsCamera Buttons Copy ButtonEsc Button Play/Stop ButtonRemote Control Buttons Power LEDUSB Port Playback Buttons Login/Logout ButtonID Button Sequence ButtonPTZ Button Alarm ButtonLayout Button Zoom ButtonInitial Unit Setup Turning on the PowerLogout screen Setup ScreenInformation System SetupChannel Digital Video Recorder Date/Time Date/Time setup screenStorage Holiday setup screenStorage Information setup screen User Storage Status setup screenOperation Instruction EZ Setup screen EZ SetupDate/Time Setup Internet Connection LAN Setup Recording Setup ShutdownRecord Very High resolution Schedule Panic Record setup screenDwell in the Settings column, the DVR Pre-Event Alarm-In Event SetupAlarm-In Actions 1 setup screen Motion Detection Motion Detection Actions 1 setup screen Video Loss Motion Detection Actions 2 setup screenVideo Blind DVR checks to see if anything is blinding the camera Text-In Text-In Device setup screenOperation Instruction System Event Text-In Actions setup screenHealth Check setup screen Event Status Network Network SetupNetwork setup screen IP Address Gateway Subnet Mask Dvrns setup screen Help Desk Notification Speco Remote setup screenHighlight the + and press the button to add a mail recipient Notification SNS setup screen Camera Devices SetupHighlight the PTZ tab, and the PTZ setup screen displays Audio Alarm-OutDigital Deterrent Alarm-Out Schedule setup screenOperation Instruction Display Display OSD setup screenMain Monitor setup screen Remote Control setup screen Remote ControlOperation Instruction Live Monitoring OperationFreeze Live Monitoring Menu DisplayAlarm SequenceCamera Menu Active Cameo Mode SetupSearch Mode Login/LogoutCovert Camera Zoom ModePTZ Mode Event MonitoringZoom In / Out Recording Video Recording AudioPlaying Recorded Video Search menu Searching VideoSearch Menu Display SearchGo To Export Data Source ExitEvent Log Search Operation Instruction Record Table Search screen Record Table SearchMotion Search Configuration Digital Deterrent section for more detailsChannel Digital Video Recorder Text-In Search screen Text-In SearchClip-Copy screen Clip-CopyOperation Instruction Preparing the USB hard disk drive in Windows USB Hard Disk Drive PreparationSearch Example Text-In Search ExamplesSpeco Remote Operation Instruction Web Monitoring Mode  Change Camera Title Changes the camera name Web Search ModeChannel Digital Video Recorder System Log Notices Problem Possible Solution Error Code NoticesTroubleshooting System Upgrade Related Clip Copy RelatedMap of Screens Video SpecificationsGeneral