Speco Technologies CS8, CS4 manual IP Address Gateway Subnet Mask

Page 54

Operation Instruction

Figure 46 ─ LAN (Manual) setup screen.

Highlight the box beside Type and press the button. You can select the type of network configuration from: Manual, DHCP and ADSL (with PPPoE). Select the desired type and press the button.

Selecting Manual from the Type allows you to set up LAN parameters manually.

Change the numbers by highlighting them and using the Up and Down arrow buttons to increase or decrease the number. The factory default LAN settings are:

IP Address: 192.168.1.129

Gateway: 192.168.1.254

Subnet Mask: 255.255.255.0

NOTE: You will need to get the appropriate IP Address, Gateway and Subnet Mask from your network administrator.

Highlight the box beside DNS Server. Press the Up and Down arrow buttons to set the IP address of the DNS server.

Highlight Use UPnP and press the button to toggle between On and Off. When it is On, port forwarding from the NAT (Network Address Translation) device to the DVR will be enabled automatically via UPnP (Universal Plug and Play) service. This function will be especially useful when accessing a port on a private IP address.

NOTE: For the UPnP service to work, the NAT device should support the UPnP Port Forwarding function and the function should be set to enabled.

NOTE: You cannot change the port settings when Use UPnP is On.

Highlight the Status box and press the button to display the port numbers forwarded from the NAT device via UPnP service.

Highlight the Port Number Setup… box and press the button. The Port Number Setup screen appears.

Change the numbers by highlighting them and using the Up and Down arrow buttons to increase or decrease the number. The factory default Port settings are:

Remote Admin:

8200

Remote Callback:

8201

Remote Watch:

8016

Remote Search:

10019

Remote Audio:

8116

 

 

NOTE: You will need to get the appropriate Port Numbers for each Speco Central and Speco Remote related program (Admin, Callback, Watch, Search and Audio) from your network administrator.

NOTE: Do NOT use the same port number for two different programs, otherwise, the DVR cannot be connected with the PC running Speco Central or Speco Remote.

44

Image 54
Contents Page Page Compliance Notice of FCC Weee Waste Electrical & Electronic Equipment Table of Contents Operation Instruction Channel Digital Video Recorder List of Illustrations Vii Operation Instruction Viii Features Technical OverviewTypical DVR installation Package Contents Required Installation ToolsVideo Out Factory Reset SwitchAudio In/Out Network PortAlarm Input/Output RS485 PortPower Cord Connector Front Panel Controls Menu ButtonPlay/Stop Button Copy ButtonEsc Button Camera ButtonsRemote Control Buttons Power LEDUSB Port Sequence Button Login/Logout ButtonID Button Playback ButtonsZoom Button Alarm ButtonLayout Button PTZ ButtonTurning on the Power Initial Unit SetupSetup Screen Logout screenSystem Setup InformationChannel Digital Video Recorder Date/Time setup screen Date/TimeHoliday setup screen StorageStorage Information setup screen Storage Status setup screen UserOperation Instruction EZ Setup EZ Setup screenDate/Time Setup Internet Connection LAN Setup Recording Setup ShutdownRecord Very High resolution Panic Record setup screen ScheduleDwell in the Settings column, the DVR Pre-Event Event Setup Alarm-InAlarm-In Actions 1 setup screen Motion Detection Motion Detection Actions 1 setup screen Motion Detection Actions 2 setup screen Video LossVideo Blind DVR checks to see if anything is blinding the camera Text-In Device setup screen Text-InOperation Instruction Text-In Actions setup screen System EventHealth Check setup screen Event Status Network Setup NetworkNetwork setup screen IP Address Gateway Subnet Mask Dvrns setup screen Help Desk Speco Remote setup screen NotificationHighlight the + and press the button to add a mail recipient Notification SNS setup screen Devices Setup CameraHighlight the PTZ tab, and the PTZ setup screen displays Alarm-Out AudioAlarm-Out Schedule setup screen Digital DeterrentOperation Instruction Display OSD setup screen DisplayMain Monitor setup screen Remote Control Remote Control setup screenOperation Instruction Operation Live MonitoringLive Monitoring Menu Display FreezeAlarm SequenceCamera Menu Login/Logout SetupSearch Mode Active Cameo ModeEvent Monitoring Zoom ModePTZ Mode Covert CameraZoom In / Out Recording Video Recording AudioPlaying Recorded Video Searching Video Search menuSearch Menu Display SearchGo To Export Data Source ExitEvent Log Search Operation Instruction Record Table Search Record Table Search screenConfiguration Digital Deterrent section for more details Motion SearchChannel Digital Video Recorder Text-In Search Text-In Search screenClip-Copy Clip-Copy screenOperation Instruction USB Hard Disk Drive Preparation Preparing the USB hard disk drive in WindowsText-In Search Examples Search ExampleSpeco Remote Operation Instruction Web Monitoring Mode Web Search Mode  Change Camera Title Changes the camera nameChannel Digital Video Recorder System Log Notices System Upgrade Related Clip Copy Related Error Code NoticesTroubleshooting Problem Possible SolutionMap of Screens Specifications VideoGeneral