Agilent Technologies ES, 8753ET quick start Verify the Analyzer Operation

Page 26

Installing Your Analyzer

STEP 5. Verify the Analyzer Operation

STEP 5. Verify the Analyzer Operation

The following procedures show you how to check your analyzer for correct operation:

•viewing installed options

•initiating self-test

•running operator's check

•testing transmission mode

•testing reﬂection mode

NOTE	If the analyzer should fail any of the following tests, call the nearest Agilent
	Technologies sales or service ofﬁce to determine the type of warranty you
	have. If repair is necessary, send the analyzer (and the EEPROM backup
	disk) to the nearest Agilent Technologies service center with a description of
	any failed test and any error message. Ship the analyzer using the original
	packaging materials. Returning the analyzer in anything other than the
	original packaging may result in non-warranted damage. A table listing of
	Agilent Technologies sales and service ofﬁces is provided in Table 2-1 on
	page 2-28.


NOTE	The illustrations depicting the analyzer display were made using an ES
	model. Other analyzer displays may appear different, depending on model
	and options.

1-20

Chapter 1

Image 26

Contents Installation and Quick Start Guide Part Number Print Date FebruaryPage Certiﬁcation General Safety Considerations How to Use This Guide Documentation Map Contents Installing Your Analyzer Introduction Verify the Shipment Item Number Part Number Description Familiarize Yourself with the Analyzer Front and Rear Panels Analyzer Front PanelAnalyzer Rear Panel Test SequenceMeet Electrical and Environmental Requirements Meet Electrical and Environmental Requirements Conﬁgure the Analyzer To Conﬁgure the Standard Analyzer To Conﬁgure the Analyzer with Printers or Plotters Plotter Port Conﬁgure the Analyzer Thinkjet Deskjet SET Clock To Conﬁgure the Analyzer for Bench Top or Rack Mount Use To Attach Front Handles to the Analyzer Standard Conﬁgure the Analyzer Conﬁgure the Analyzer Verify the Analyzer Operation To View the Installed Options To Initiate the Analyzer Self-Test Service Menu Tests To Run the Operators CheckTo Test the Transmission Mode Trans FWD S21B/R or TransmissnTo Test the Reﬂection Mode Description Eeprom Backup Disk ProcedureBack Up the Eeprom Disk EquipmentBack Up the Eeprom Disk Quick Start Learning How to Make Measurements Quick Start Learning How to Make Measurements Analyzer Front Panel Analyzer Front PanelAnalyzer Front Panel Measure the device Measurement ProcedureMake a measurement calibration Output measurement resultsChoose the following measurement settings Learning to Make Transmission MeasurementsPerform a measurement calibration Connections for a Thru Calibration StandardExample Measurement of Insertion Loss Press Return Define DISK-SAVE Measuring Other Transmission Characteristics Example Measurement of 3 dB BandwidthLearning to Make Transmission Measurements Measuring Out-of-Band Rejection Example Measurement of Out-of-Band RejectionMeasuring Passband Flatness or Ripple Example Measurement of Passband Flatness or Ripple= 1 + ρ / 1 − ρ Learning to Make Reﬂection Measurements= Γ Connections for Reﬂection Measurements Make a measurement calibration Measuring Return Loss 10 Example Measurement of Return Loss11 Example Measurement Title Measuring Other Reﬂection Characteristics Measuring Reﬂection CoefﬁcientMeasuring Standing Wave Ratio SWR 13 Example Standing-Wave-Ratio Measurement TraceMeasuring S11 and S22 or Reﬂection in a Polar Format Measuring Impedance 15 Example Impedance Measurement Trace 16 Example Admittance Measurement Trace If the analyzer display does not light If You Encounter a ProblemPower-Up Problems No RF Output Data Entry ProblemsIf there is no RF signal at the front-panel port If You Encounter a Problem Agilent Technologies Sales and Service Ofﬁces European Field OperationsIndex Index

Related manuals

Manual 28 pages 56.53 Kb

Manual 61 pages 32.91 Kb