Agilent Technologies ES, 8753ET quick start Index

Page 62

Index

Numerics

3 dB bandwidth measuring, 2-10

6 dB bandwidth measuring, 2-11

A

active channel keys location, 2-3

admittance measuring, 2-23

Agilent Technologies Sales and

Service Offices, 2-28analyzer configuration, 1-91-19

attaching cabinet flanges with front handles, 1-19

attaching cabinet flanges without front handles, 1-18

attaching front handles, 1-17for bench top use, 1-16

for rack mount use, 1-16option 1D5, 1-10standard, 1-10

with printers or plotters, 1-11

B

backing up EEPROM disk, 1-26bench top configuration, 1-16

C

connectors

probe power source, 2-4R channel, 2-4

D

definitions magnitude of reflection

coefficient, 2-14reflection coefficient, 2-14return loss (dB), 2-14standing-wave-ratio (SWR),

2-14

disk drive location, 2-3disk eject button, 2-3display location, 2-3

E

EEPROM backup disk, 1-26electrical and environmental

requirements, 1-7entry block location, 2-4

F

front panel, 1-5,2-3

H

high stability frequency reference configuration, 1-10

I

impedance measuring, 2-22

insertion loss measuring, 2-8

installation, 1-2

instrument state function block keys, 2-4

L

line switch, 2-3location

active channel keys, 2-3disk drive, 2-3

disk eject button, 2-3display, 2-3

entry block, 2-4

instrument state function block keys, 2-4

line switch, 2-3PORT 1, 2-4PORT 2, 2-4Preset key, 2-4

probe power source connectors, 2-4

R channel connectors, 2-4REFLECTION port, 2-4response function block keys,

2-3Return key, 2-3softkeys, 2-3

stimulus function block keys, 2-3

TRANSMISSION port, 2-4

M

making measurements, 2-12-24measurement procedure, 2-5

choosing measurement parameters, 2-5making a measurement calibration, 2-5measuring a device, 2-5outputting measurement

results, 2-5measuring insertion loss with

marker functions, 2-10

O

operation, 1-201-25installed options, 1-21

operator’s check, 1-23self-test,1-22

testing reflection mode, 1-25testing transmission mode, 1-24

operator’s check, 1-23out-of-band rejection measuring, 2-12

P

parts list

parts received, 1-4passband flatness

measuring, 2-13passband ripple

measuring, 2-13plotter configuration, 1-11polar format

measuring, 2-21PORT 1

location, 2-4PORT 2

location, 2-4Preset key

location, 2-4

printer configuration, 1-11probe power connectors

location, 2-4problems, data entry, 2-26

controls do not respond, 2-26parameters not accepted, 2-26

problems, power-up,2-252-26display does not light, 2-25display lights but fan does not

start, 2-26problems, RF output, 2-26

no RF signal at front panel port, 2-26

R

R channel connectors location, 2-4

rack mount configuration, 1-16rear panel, 1-6

reflection measurements, 2-142-24

admittance, 2-23choosing measurement

parameters, 2-15impedance, 2-22making a measurement

calibration, 2-16measuring in polar format, 2-21measuring in smith chart

format, 2-22

measuring reflection coefficient, 2-19

measuring return loss, 2-17

Index

1

Image 62
Contents Installation and Quick Start Guide Part Number Print Date FebruaryPage Certification General Safety Considerations How to Use This Guide Documentation Map Contents Installing Your Analyzer Introduction Verify the Shipment Item Number Part Number Description Familiarize Yourself with the Analyzer Front and Rear Panels Analyzer Front PanelAnalyzer Rear Panel Test SequenceMeet Electrical and Environmental Requirements Meet Electrical and Environmental Requirements Configure the Analyzer To Configure the Standard Analyzer To Configure the Analyzer with Printers or Plotters Plotter Port Configure the Analyzer Thinkjet Deskjet SET Clock To Configure the Analyzer for Bench Top or Rack Mount Use To Attach Front Handles to the Analyzer Standard Configure the Analyzer Configure the Analyzer Verify the Analyzer Operation To View the Installed Options To Initiate the Analyzer Self-Test Service Menu Tests To Run the Operators CheckTo Test the Transmission Mode Trans FWD S21B/R or TransmissnTo Test the Reflection Mode Description Eeprom Backup Disk ProcedureBack Up the Eeprom Disk EquipmentBack Up the Eeprom Disk Quick Start Learning How to Make Measurements Quick Start Learning How to Make Measurements Analyzer Front Panel Analyzer Front PanelAnalyzer Front Panel Measure the device Measurement ProcedureMake a measurement calibration Output measurement resultsChoose the following measurement settings Learning to Make Transmission MeasurementsPerform a measurement calibration Connections for a Thru Calibration StandardExample Measurement of Insertion Loss Press Return Define DISK-SAVE Measuring Other Transmission Characteristics Example Measurement of 3 dB BandwidthLearning to Make Transmission Measurements Measuring Out-of-Band Rejection Example Measurement of Out-of-Band RejectionMeasuring Passband Flatness or Ripple Example Measurement of Passband Flatness or Ripple= 1 + ρ / 1 − ρ Learning to Make Reflection Measurements= Γ Connections for Reflection Measurements Make a measurement calibration Measuring Return Loss 10 Example Measurement of Return Loss11 Example Measurement Title Measuring Other Reflection Characteristics Measuring Reflection CoefficientMeasuring Standing Wave Ratio SWR 13 Example Standing-Wave-Ratio Measurement TraceMeasuring S11 and S22 or Reflection in a Polar Format Measuring Impedance 15 Example Impedance Measurement Trace 16 Example Admittance Measurement Trace If the analyzer display does not light If You Encounter a ProblemPower-Up Problems No RF Output Data Entry ProblemsIf there is no RF signal at the front-panel port If You Encounter a Problem Agilent Technologies Sales and Service Offices European Field OperationsIndex Index
Related manuals
Manual 28 pages 56.53 Kb Manual 61 pages 32.91 Kb