Agilent Technologies 8753ET, ES Familiarize Yourself with the Analyzer Front and Rear Panels

Page 11

Installing Your Analyzer

STEP 2. Familiarize Yourself with the Analyzer Front and Rear Panels

STEP 2. Familiarize Yourself with the Analyzer Front and Rear Panels

Analyzer Front Panel

CAUTION Do not mistake the line switch for the disk eject button. See the ﬁgure below. If the line switch is mistakenly pushed, the instrument will be turned off, losing all settings and data that have not been saved.


1 LINE (power on/off) switch	8 RESPONSE function block
2 Display	9 ACTIVE CHANNEL keys
3 Disk drive	10 ENTRY block
4 Disk eject button	11 INSTRUMENT STATE function block
5 Softkeys	12 Preset key
6 Return key	13 PROBE POWER connectors
7 STIMULUS function block	14 R CHANNEL connectors
	15 ES models only:	ET models only:
	PORT 1	REFLECTION
	and	and
	PORT 2	TRANSMISSION

Chapter 1

1-5

Image 11

Contents Part Number Print Date February Installation and Quick Start GuidePage Certiﬁcation General Safety Considerations How to Use This Guide Documentation Map Contents Installing Your Analyzer Introduction Verify the Shipment Item Number Part Number Description Analyzer Front Panel Familiarize Yourself with the Analyzer Front and Rear PanelsTest Sequence Analyzer Rear PanelMeet Electrical and Environmental Requirements Meet Electrical and Environmental Requirements Conﬁgure the Analyzer To Conﬁgure the Standard Analyzer To Conﬁgure the Analyzer with Printers or Plotters Plotter Port Conﬁgure the Analyzer Thinkjet Deskjet SET Clock To Conﬁgure the Analyzer for Bench Top or Rack Mount Use To Attach Front Handles to the Analyzer Standard Conﬁgure the Analyzer Conﬁgure the Analyzer Verify the Analyzer Operation To View the Installed Options To Initiate the Analyzer Self-Test To Run the Operators Check Service Menu TestsTrans FWD S21B/R or Transmissn To Test the Transmission ModeTo Test the Reﬂection Mode Equipment Eeprom Backup Disk ProcedureBack Up the Eeprom Disk DescriptionBack Up the Eeprom Disk Quick Start Learning How to Make Measurements Quick Start Learning How to Make Measurements Analyzer Front Panel Analyzer Front PanelAnalyzer Front Panel Output measurement results Measurement ProcedureMake a measurement calibration Measure the deviceLearning to Make Transmission Measurements Choose the following measurement settingsConnections for a Thru Calibration Standard Perform a measurement calibrationExample Measurement of Insertion Loss Press Return Define DISK-SAVE Example Measurement of 3 dB Bandwidth Measuring Other Transmission CharacteristicsLearning to Make Transmission Measurements Example Measurement of Out-of-Band Rejection Measuring Out-of-Band RejectionExample Measurement of Passband Flatness or Ripple Measuring Passband Flatness or Ripple= 1 + ρ / 1 − ρ Learning to Make Reﬂection Measurements= Γ Connections for Reﬂection Measurements Make a measurement calibration 10 Example Measurement of Return Loss Measuring Return Loss11 Example Measurement Title Measuring Reﬂection Coefﬁcient Measuring Other Reﬂection Characteristics13 Example Standing-Wave-Ratio Measurement Trace Measuring Standing Wave Ratio SWRMeasuring S11 and S22 or Reﬂection in a Polar Format Measuring Impedance 15 Example Impedance Measurement Trace 16 Example Admittance Measurement Trace If the analyzer display does not light If You Encounter a ProblemPower-Up Problems No RF Output Data Entry ProblemsIf there is no RF signal at the front-panel port If You Encounter a Problem European Field Operations Agilent Technologies Sales and Service OfﬁcesIndex Index

Related manuals

Manual 28 pages 56.53 Kb

Manual 61 pages 32.91 Kb