Agilent Technologies ES, 8753ET quick start Analyzer Front Panel

Page 36

Quick Start: Learning How to Make Measurements

Analyzer Front Panel

Analyzer Front Panel

CAUTION Do not mistake the line switch for the disk eject button. See the ﬁgure below. If the line switch is mistakenly pushed, the instrument will be turned off, losing all settings and data that have not been saved.

Figure 2-1 The Analyzer Front Panel

1.LINE switch. This switch controls AC power to the analyzer. 1 is on, 0 is off.

2.Display. This shows the measurement data traces, measurement annotation, and softkey labels.

3.Disk drive. This 3.5-inch drive allows you to store and recall instrument states and measurement results for later analysis.

4.Disk eject button. This button ejects the disk from the disk drive.

5.Softkeys. These keys provide access to menus that are shown on the display.

6.Return key. This key returns the previous softkey menu shown on the display.

7.STIMULUS function block. The keys in this block allow you to control the analyzer source's frequency, power, and other stimulus functions.

8.RESPONSE function block. The keys in this block allow you to control the measurement and display functions of the active display channel.

Chapter 2

2-3

Image 36

Contents Installation and Quick Start Guide Part Number Print Date FebruaryPage Certiﬁcation General Safety Considerations How to Use This Guide Documentation Map Contents Installing Your Analyzer Introduction Verify the Shipment Item Number Part Number Description Familiarize Yourself with the Analyzer Front and Rear Panels Analyzer Front PanelAnalyzer Rear Panel Test SequenceMeet Electrical and Environmental Requirements Meet Electrical and Environmental Requirements Conﬁgure the Analyzer To Conﬁgure the Standard Analyzer To Conﬁgure the Analyzer with Printers or Plotters Plotter Port Conﬁgure the Analyzer Thinkjet Deskjet SET Clock To Conﬁgure the Analyzer for Bench Top or Rack Mount Use To Attach Front Handles to the Analyzer Standard Conﬁgure the Analyzer Conﬁgure the Analyzer Verify the Analyzer Operation To View the Installed Options To Initiate the Analyzer Self-Test Service Menu Tests To Run the Operators CheckTo Test the Transmission Mode Trans FWD S21B/R or TransmissnTo Test the Reﬂection Mode Eeprom Backup Disk Procedure Back Up the Eeprom DiskDescription EquipmentBack Up the Eeprom Disk Quick Start Learning How to Make Measurements Quick Start Learning How to Make Measurements Analyzer Front Panel Analyzer Front PanelAnalyzer Front Panel Measurement Procedure Make a measurement calibrationMeasure the device Output measurement resultsChoose the following measurement settings Learning to Make Transmission MeasurementsPerform a measurement calibration Connections for a Thru Calibration StandardExample Measurement of Insertion Loss Press Return Define DISK-SAVE Measuring Other Transmission Characteristics Example Measurement of 3 dB BandwidthLearning to Make Transmission Measurements Measuring Out-of-Band Rejection Example Measurement of Out-of-Band RejectionMeasuring Passband Flatness or Ripple Example Measurement of Passband Flatness or RippleLearning to Make Reﬂection Measurements = Γ= 1 + ρ / 1 − ρ Connections for Reﬂection Measurements Make a measurement calibration Measuring Return Loss 10 Example Measurement of Return Loss11 Example Measurement Title Measuring Other Reﬂection Characteristics Measuring Reﬂection CoefﬁcientMeasuring Standing Wave Ratio SWR 13 Example Standing-Wave-Ratio Measurement TraceMeasuring S11 and S22 or Reﬂection in a Polar Format Measuring Impedance 15 Example Impedance Measurement Trace 16 Example Admittance Measurement Trace If You Encounter a Problem Power-Up ProblemsIf the analyzer display does not light Data Entry Problems If there is no RF signal at the front-panel portNo RF Output If You Encounter a Problem Agilent Technologies Sales and Service Ofﬁces European Field OperationsIndex Index

Related manuals

Manual 28 pages 56.53 Kb

Manual 61 pages 32.91 Kb