Fluke 80 Series V manual Current Function Specifications, Function Range Resolution Accuracy Model

80 Series V

Calibration Manual

Table 4. DC Voltage, Resistance, and Conductance Function Specifications

Function	Range		Resolution		Accuracy
				Model 83	Model 87	Model 88
L	6.000	V	0.001 V	± (0.1 % + 1)	± (0.05 % + 1)	± (0.1 % + 1)
	60.00	V	0.01 V	± (0.1 % + 1)	± (0.05 % + 1)	± (0.1 % + 1)
	600.0	V	0.1 V	± (0.1 % + 1)	± (0.05 % + 1)	± (0.1 % + 1)
	1000 V		1 V	± (0.1 % + 1)	± (0.05 % + 1)	± (0.1 % + 1)
F	600.0 mV		0.1 mV	± (0.3 % + 1)	± (0.1 % + 1)	± (0.3 % + 1)
mV
e	600.0	Ω	0.1 Ω	± (0.4 % + 2)1	± (0.2 % + 2)1	± (0.4 % + 2)1
	6.000 kΩ		0.001 kΩ	± (0.4 % + 1)	± (0.2 % + 1)	± (0.4 % + 1)
	60.00 kΩ		0.01 kΩ	± (0.4 % + 1)	± (0.2 % + 1)	± (0.4 % + 1)
	600.0 kΩ		0.1 kΩ	± (0.7 % + 1)	± (0.6 % + 1)	± (0.7 % + 1)
	6.000	MΩ	0.001 MΩ	± (0.7 % + 1)	± (0.6 % + 1)	± (0.7 % + 1)
nS	50.00	MΩ	0.01 MΩ	± (1.0 % + 3)2	± (1.0 % + 3)2	± (1.0 % + 3)2
	60.00 nS		0.01 nS	± (1.0 % + 10)1	± (1.0 % + 10)1	± (1.0 % + 10)1

1. When using the REL ∆ function to compensate for offsets.

2. Add 0.5 % of reading when measuring above 30 MΩ in the 50 MΩ range, and 20 counts below 33 nS in the 60 nS range.

Table 5. Temperature Specifications (87 and 88 Only)

		Temperature		Resolution	Accuracy1,2
-200		°C to +1090 °C	0.1	°C	1 % + 10
-328		°F to +1994 °F	0.1	°F	1 % + 18
1.	Does not include error of the thermocouple probe.
2.	Accuracy specification assumes ambient temperature stable to ± 1 °C. For ambient temperature changes of ± 5 °C,

rated accuracy applies after 1 hour.

Table 6. Current Function Specifications

Function		Range		Resolution		Accuracy		Burden
					Model 831	Model 872, 3	Model 881	Voltage
								(typical)
mA		60.00 mA		0.01 mA	± (1.2 % + 2)5	± (1.0 % + 2)	± (1.2 % + 2)5	1.8 mV/mA
\		400.0 mA6		0.1 mA	± (1.2 % + 2)5	± (1.0 % + 2)	± (1.2 % + 2)5	1.8 mV/mA
		6.000	A	0.001 A	± (1.2 % + 2)5	± (1.0 % + 2)	± (1.2 % + 2)5	0.03 V/A
(45 Hz to
		10.00	A4	0.01 A	± (1.2 % + 2)5	± (1.0 % + 2)	± (1.2 % + 2)5	0.03 V/A
2 kHz)
		60.00 mA		0.01 mA	± (0.4 % + 4)	± (0.2 % + 4)	± (0.4 % + 4)	1.8 mV/mA
mA		400.0 mA6		0.1 mA	± (0.4 % + 2)	± (0.2 % + 2)	± (0.4 % + 2)	1.8 mV/mA
[		6.000	A	0.001 A	± (0.4 % + 4)	± (0.2 % + 4)	± (0.4 % + 4)	0.03 V/A
∝A B		10.00	A4	0.01 A	± (0.4 % + 2)	± (0.2 % + 2)	± (0.4 % + 2)	0.03 V/A
		600.0	∝A	0.1 ∝A	± (1.2 % + 2)5	± (1.0 % + 2)	± (1.2 % + 2)5	100 ∝V/∝A
(45 Hz to		6000 ∝A		1 ∝A	± (1.2 % + 2)5	± (1.0 % + 2)	± (1.2 % + 2)5	100 ∝V/∝A
2 kHz)
∝AF		600.0	∝A	0.1 ∝A	± (0.4 % + 4)	± (0.2 % + 4)	± (0.4 % + 4)	100 ∝V/∝A
		6000 ∝A		1 ∝A	± (0.4 % + 2)	± (0.2 % + 2)	± (0.4 % + 2)	100 ∝V/∝A
1.	AC conversion for Model 83 and 88 is ac coupled and calibrated to the rms value of a sine wave input.
2.	AC conversions for Model 87 are ac coupled, true rms responding, and valid from 3 % to 100 % of range, except
	400 mA range (5 % to 100 % of range) and 10 A range (15 % to 100 % or range).
3.	Model 87 is a true rms responding meter. When the input leads are shorted together in the ac functions, the Meter
	may display a residual reading between 1 and 30 counts. A 30 count residual reading will cause only a 2 digit
	change for readings over 3 % of range. Using REL to offset this reading may produce a much larger constant
	error in later measurements
4.	W 10 A continuous up to 35 °C; < 20 minutes on, 5 minutes off at 35 °C to 55 °C. 20 A for 30 seconds maximum;
	> 10 A unspecified.
5.	Below a reading of 200 counts, add 10 counts.
6.	400 mA continuous; 600 mA for 18 hrs maximum.

6