Panasonic DW5100UL, PT-D5700UL, PT-DW5100U Name and function of parts, Remote control

Page 9

Name and function of parts

Remote control

Remote control operation indicator lamp

The lamp flashes when any remote control button is pressed.

POWER STANDBY ( ) button (page 25)

Switched the power to the “standby” mode if the MAIN POWER has been put to the “l” position.

POWER ON ( I ) button (page 24)

Turns on the power if the MAIN POWER has been put to the “l” position.

Input selector (RGB1, RGB2, DVI-D, VIDEO, S-VIDEO) button

Use to toggle through the RGB1, RGB2, DVI-D, VIDEO and S-VIDEO input ports.

MENU button (page 29)

Displays and clears the MAIN MENU. It can also return to the previous screen when the menu is displayed.

Arrow buttons (page 29)

Use these buttons to select an item on the menu screen, change setting and adjust the level.

Also use them to enter the “SECURITY” password.

ENTER button (page 29)

Press this button to enter your menu selection or to run function.

ON SCREEN button

This button turns on and off the on-screen indication function.

TEST PATTERN button (page 40)

This displays the test pattern.

Numeric (0 - 9) buttons (pages 15, 40)

These buttons are used for systems where more than one projector is being used.

They are used to enter ID numbers when selecting an ID, and they are also used by service personnel for entering passwords when password entry is needed.

STATUS button (page 27)

Press this button to display projector information. It can also be used to send information about the projector’s status via E-mail.

AUTO SETUP button (page 27)

Pressing this button while projecting an image automatically corrects the picture positioning on the screen. While the auto setup feature is active, a message “AUTO SETUP” appears on the screen.

SHUTTER button (page 27)

Press this button to black out the image temporarily.

ASPECT button (page 31)

Switches the image aspect ratio.

9

Page 8 Page 10
Image 9
Page 8 Page 10
Contents Model No. PT-D5700U Commercial UseDear Panasonic Customer Model number PT-D5700U/PT-D5700UL/PT-DW5100U/PT-DW5100ULSerial number PT-D5700U/PT-D5700UL/PT-DW5100U/PT-DW5100UL Contents Precautions with regard to safety Do not use or handle the batteries improperly Remove empty batteries from the remote control at onceDo not disassemble the lamp unit Always disconnect all cables before moving the projectorDo not use the old lamp unit AccessoriesDo not place the projector in extremely hot locations Electric shocks can result if this is not donePrecautions on handling Name and function of parts Remote controlBottom Status LED lights Front and side of the projectorRear view of the main unit Controls on rear panel Side-mounted connection terminals Using the remote control unit Effective range of remote control operationLoading dry cells Connect to the projector to use with a cable Setting projector ID number to remote controlInstallation Installation geometryProjection schemes PT-D5700U, PT-D5700UL Screen aspect ratio Projection distance by projection lensInstallation Screen aspect ratio PT-DW5100U, PT-DW5100ULET-DLE100 ET-DLE200 ET-DLE310 ET-DLE410 PT-DW5100U, PT-DW5100UL Screen aspect ratioCalculation formulas for projection distance by lens types Setup precautions ConnectionPin assignments on the RGB2 input terminal are as follows Example of connecting with PCs Example of connecting with AV productsMaking adjustment and selection Powering up the projectorPress the I button. on the main unit or the remote control When operating at the projector, please refer toDirect power off function Powering off the projectorHow to adjust the lens How to adjust the FOCUS, Zoom and ShiftHow to remove the projection lens Press the Status button on the remote control Automatic adjustmentStatus function Press the Shutter button againFor DVI signals For RGB signalsFor S-Video/Video/YPBPRsignals On-screen menusResetting to the factory default Menu items settingBasic menu operations Returning to the previousAdjusting the picture Adjusting the position Zoom Clock PhaseKeystone Digital Cinema RealityInput Resolution Clamp PositionEdge Blending Sxga Mode XGA ModePress to select an item, and press to adjust the setting Raster PositionPress the Enter button Press to adjust the values OPTION1 settingsColor Matching Press to select R, G, B and WhAuto Signal Contrast ModeColor Correction Back ColorDVI Edid DVI Signal LevelFUNC1 OSD PositionInstallation OPTION2 settingsProjector ID AltitudeLamp Select Lamp PowerLamp Relay RS-232CPassword Auto Power OFFSystem Information Cycle of displayed internal test patternsConnecting the PC Setting the networkSystem requirements Connection exampleAccessing from the Web browser Using Web Browser ControlPassword change Click Change passwordChange password button Basic controlDetail control Error information Monitor informationOK Normal operation Failed Occurrence of trouble When Failed has appeared for an item Parameter Description Mail set upAn error is detected by self- diagnosis Mail setup page ContinuingDNS server set up Authentication server set upChange the authentication method as desired Ping testAdjust clock Contents of mail sentNetwork status Network configSupported commands Using the PJLink protocolPJLink security authentication Command Control Description RemarksPassword Change Setting the securityDisplay Setting Control Device SetupPin assignments and signal names Using the serial terminalsCommunication conditions Factory setting Examples of connectionCable specifications Control commandsConnecting to a PC Computer Projector DTE specifications Pin assignments and controlIndication of lamp monitor Procedure of cleaning Cleaning and replacement of air filterClean the air filter Dismantle the air filterReplacing the lamp unit When to replace the Lamp unitLamp AfterRemove the two screws securing the fan unit Lamp unit replacement stepsLamp unit will be hot after it has been used Have a Phillips screwdriver ready ahead of timeInstallation procedure Ceiling Mount Bracket SafeguardsNot turn on Power doesNo image Image is blurredPT-D5700U PT-D5700UL PT-DW5100U SpecificationsOutside dimensions Length of power cord CabinetRemote control Power source Replacement lamp unitPAL-M/PAL60 PAL/PAL-N/SECAM Compatible Signal ListDimensions Installation dimensions diagramUnit mm, inch Trademark Acknowledgement Concernant LA Sécurité Ne pas surcharger la prise de courant Précautions concernant la sécuritéNe jamais tenter de modifier ou de démonter le projecteur Ne pas mettre d’objets étrangers dans le projecteurNe jamais démonter la lampe Pendant un orage, ne pas toucher le projecteur ou le câbleIl y a risque d’électrocution Il y a risque d’électrocution ou d’explosionNe pas utiliser la lampe usée Ne pas empêcher la chaleur de s’échapperSinon cela peut causer des chocs électriques Le bloc lampe risquerait de se casserPrécautions pour la manipulation Nettoyage et maintenanceMise au rebut Précautions pour l’utilisationMoment adéquat pour remplacer la lampe Remplacement de la lampeAprès Heures*2La lampe est chaude si elle vient d’être utilisée Procédure de remplacement de la lampePréparez un tournevis Phillips à l’avance Poignée LampeTechnical Support Panasonic Projector Systems CompanyPhone FAX Mail projectorsupport@us.panasonic.com Panasonic Canada Inc

PT-DW5100U, PT-D5700U, DW5100UL, PT-D5700UL specifications

Panasonic, a leader in innovative projection technology, offers a range of high-performance projectors including the PT-D5700UL, DW5100UL, PT-D5700U, and PT-DW5100U. These models are designed for environments that require high brightness, excellent color accuracy, and advanced features for seamless integration into various applications.

The PT-D5700UL and PT-D5700U are renowned for their high brightness of up to 7,000 lumens, making them ideal for large venues such as auditoriums, conference rooms, and outdoor events. They utilize a dual-lamp system, which not only enhances brightness but also provides reliability and longevity. The unique Dual Lamp Drive system ensures that if one lamp fails, the other continues to function, minimizing downtime and maintenance concerns.

Both projectors feature a WUXGA resolution of 1920 x 1200, providing sharp, detailed images that are essential for professional presentations. Their RGB booster technology enhances color reproduction, delivering vivid and realistic colors that captivate audiences. Additionally, these models feature a contrast ratio of up to 20,000:1, allowing presentations to have deep blacks and bright highlights, critical for effective visual storytelling.

On the other hand, the DW5100UL and PT-DW5100U models are specifically tailored for applications requiring exceptional brightness and excellent color fidelity, boasting a brightness of 5,000 lumens. They offer WXGA resolution (1280 x 800), making them suitable for a wide variety of display needs in corporate, educational, and entertainment settings. The incorporation of Panasonic’s Daylight View technology significantly enhances visibility even in brightly lit environments.

All four projectors are equipped with advanced connectivity options, including HDMI, DisplayPort, and LAN, allowing for easy integration into existing AV systems. They are also compatible with Crestron and AMX control systems, making them a flexible choice for complex installations.

Furthermore, the projectors utilize Panasonic's proprietary Solid Shine laser technology, which ensures consistent brightness and color quality over time while reducing maintenance requirements. With IP6X-rated dust-proof design and a cooling system that minimizes dust accumulation, users can rely on these projectors to perform optimally in challenging conditions.

In summary, Panasonic’s PT-D5700UL, DW5100UL, PT-D5700U, and PT-DW5100U projectors are engineered to deliver outstanding performance, durability, and versatility. They set a high standard for professional projection systems, equipped with cutting-edge technologies that ensure exceptional visual quality whether for business, education, or entertainment purposes.
Top Page Image Contents