Panasonic DW5100UL Color Correction, Contrast Mode, Auto Signal, Back Color, Startup Logo

Page 36

OPTION1 settings

After all the data has been input, press the MENU button.

The “COLOR MATCHING:MEASURE” screen will be displayed.

Inputting the coordinates of a desired color

Press to select “TARGET DATA”. Press the ENTER button.

The “TARGET DATA” screen will be displayed.

Press to select the desired colors,

and press to input their coordinates.

After all the data has been input, press the MENU button.

Note • If the target data is outside the color range of the projector, the colors will not be projected correctly.

•When “AUTO TESTPATTERN” is set to “ON”, the test pattern for adjusting the adjustment color is automatically displayed.

•Set “PICTURE MODE” to “DYNAMIC” when measuring the measured data using a colorimeter or other measuring device.

•Depending on the measuring device being used and the environment in which measurements are made, discrepancies sometimes occur in the color coordinates of the target data and the values given by the measuring device.

COLOR CORRECTION

OFF : This is the standard setting.

USER : The six colors of red, green, blue, cyan, magenta and yellow can be adjusted and registered for each of four signal systems: Video, S-Video, RGB and

YPBPR.

Press the ENTER button to make the detailed settings.

COLOR CORRECTION

 

 

RGB

R

0

G

0

B

0

Cy

0

Mg

0

Ye

0

MENU SELECT

 

ADJUST

 

The current signal system is displayed.

CONTRAST MODE

There are two modes for adjusting to the operating environment.

NORMAL : The brightness is set to maximum.

HIGH

: The contrast is set to maximum.

AUTO SIGNAL

The position where the screen is displayed can be adjusted automatically without pressing the AUTO SETUP button on the remote control each time signals are input when signals are input frequently such as when the projector is used at a conference.

ON

: Auto setup is performed automatically

 

when the video signals of the images

 

being projected have changed.

OFF

: The input auto setup function is set to

 

OFF.

BACK COLOR

You can set the colors of the screen when no signal is input to the projector.

BLUE

: Set screen color to blue.

BLACK

: Set screen color to black.

LOGO1 : The picture registered by the user will be projected.

LOGO2 : The Panasonic logo is projected.

STARTUP LOGO

This sets the startup logo that is projected when the power is turned on.

LOGO2 : This is the standard setting. The Panasonic logo is projected.

NONE : “STARTUP LOGO” is disabled.

LOGO1 : The picture registered by the user will be projected.

Note • Separate software is required in order to create the pictures to use for “LOGO1”. Consult your dealer.

SUB MEMORY LIST

Multiple sets of image adjustment data (PICTURE, POSITION, ADVANCED MENU adjustment values) for the same kind of signal can be registered.

SUB MEMORY LIST

- : RGB1-XGA60

1:RGB1-XGA60

2:VIDEO-NTSC

SELECT STORE

RETURN

36

Page 35 Page 37
Image 36
Page 35 Page 37
Contents Commercial Use Model No. PT-D5700UDear Panasonic Customer Model number PT-D5700U/PT-D5700UL/PT-DW5100U/PT-DW5100ULSerial number PT-D5700U/PT-D5700UL/PT-DW5100U/PT-DW5100UL Contents Precautions with regard to safety Remove empty batteries from the remote control at once Do not use or handle the batteries improperlyDo not disassemble the lamp unit Always disconnect all cables before moving the projectorAccessories Do not use the old lamp unitDo not place the projector in extremely hot locations Electric shocks can result if this is not donePrecautions on handling Remote control Name and function of partsBottom Front and side of the projector Status LED lightsRear view of the main unit Controls on rear panel Side-mounted connection terminals Using the remote control unit Effective range of remote control operationLoading dry cells Setting projector ID number to remote control Connect to the projector to use with a cableInstallation Installation geometryProjection schemes Projection distance by projection lens PT-D5700U, PT-D5700UL Screen aspect ratioInstallation PT-DW5100U, PT-DW5100UL Screen aspect ratioPT-DW5100U, PT-DW5100UL Screen aspect ratio ET-DLE100 ET-DLE200 ET-DLE310 ET-DLE410Calculation formulas for projection distance by lens types Setup precautions ConnectionPin assignments on the RGB2 input terminal are as follows Example of connecting with AV products Example of connecting with PCsPowering up the projector Making adjustment and selectionPress the I button. on the main unit or the remote control When operating at the projector, please refer toPowering off the projector Direct power off functionHow to adjust the lens How to adjust the FOCUS, Zoom and ShiftHow to remove the projection lens Automatic adjustment Press the Status button on the remote controlStatus function Press the Shutter button againFor RGB signals For DVI signalsFor S-Video/Video/YPBPRsignals On-screen menusMenu items setting Resetting to the factory defaultBasic menu operations Returning to the previousAdjusting the picture Adjusting the position Clock Phase ZoomKeystone Digital Cinema RealityInput Resolution Clamp PositionEdge Blending XGA Mode Sxga ModePress to select an item, and press to adjust the setting Raster PositionOPTION1 settings Press the Enter button Press to adjust the valuesColor Matching Press to select R, G, B and WhContrast Mode Auto SignalColor Correction Back ColorDVI Signal Level DVI EdidFUNC1 OSD PositionOPTION2 settings InstallationProjector ID AltitudeLamp Power Lamp SelectLamp Relay RS-232CAuto Power OFF PasswordSystem Information Cycle of displayed internal test patternsSetting the network Connecting the PCSystem requirements Connection exampleUsing Web Browser Control Accessing from the Web browserPassword change Click Change passwordChange password button Basic controlDetail control Error information Monitor informationOK Normal operation Failed Occurrence of trouble Mail set up When Failed has appeared for an item Parameter DescriptionMail setup page Continuing An error is detected by self- diagnosisAuthentication server set up DNS server set upChange the authentication method as desired Ping testContents of mail sent Adjust clockNetwork config Network statusUsing the PJLink protocol Supported commandsPJLink security authentication Command Control Description RemarksSetting the security Password ChangeDisplay Setting Control Device SetupUsing the serial terminals Pin assignments and signal namesCommunication conditions Factory setting Examples of connectionControl commands Cable specificationsConnecting to a PC Computer Projector DTE specifications Pin assignments and controlIndication of lamp monitor Cleaning and replacement of air filter Procedure of cleaningClean the air filter Dismantle the air filterWhen to replace the Lamp unit Replacing the lamp unitLamp AfterLamp unit replacement steps Remove the two screws securing the fan unitLamp unit will be hot after it has been used Have a Phillips screwdriver ready ahead of timeCeiling Mount Bracket Safeguards Installation procedurePower does Not turn onNo image Image is blurredSpecifications PT-D5700U PT-D5700UL PT-DW5100ULength of power cord Cabinet Outside dimensionsRemote control Power source Replacement lamp unitCompatible Signal List PAL-M/PAL60 PAL/PAL-N/SECAMDimensions Installation dimensions diagramUnit mm, inch Trademark Acknowledgement Concernant LA Sécurité Précautions concernant la sécurité Ne pas surcharger la prise de courantNe jamais tenter de modifier ou de démonter le projecteur Ne pas mettre d’objets étrangers dans le projecteurPendant un orage, ne pas toucher le projecteur ou le câble Ne jamais démonter la lampeIl y a risque d’électrocution Il y a risque d’électrocution ou d’explosionNe pas empêcher la chaleur de s’échapper Ne pas utiliser la lampe uséeSinon cela peut causer des chocs électriques Le bloc lampe risquerait de se casserNettoyage et maintenance Précautions pour la manipulationMise au rebut Précautions pour l’utilisationRemplacement de la lampe Moment adéquat pour remplacer la lampeAprès Heures*2Procédure de remplacement de la lampe La lampe est chaude si elle vient d’être utiliséePréparez un tournevis Phillips à l’avance Poignée LampePanasonic Projector Systems Company Technical SupportPhone FAX Mail projectorsupport@us.panasonic.com Panasonic Canada Inc

PT-DW5100U, PT-D5700U, DW5100UL, PT-D5700UL specifications

Panasonic, a leader in innovative projection technology, offers a range of high-performance projectors including the PT-D5700UL, DW5100UL, PT-D5700U, and PT-DW5100U. These models are designed for environments that require high brightness, excellent color accuracy, and advanced features for seamless integration into various applications.

The PT-D5700UL and PT-D5700U are renowned for their high brightness of up to 7,000 lumens, making them ideal for large venues such as auditoriums, conference rooms, and outdoor events. They utilize a dual-lamp system, which not only enhances brightness but also provides reliability and longevity. The unique Dual Lamp Drive system ensures that if one lamp fails, the other continues to function, minimizing downtime and maintenance concerns.

Both projectors feature a WUXGA resolution of 1920 x 1200, providing sharp, detailed images that are essential for professional presentations. Their RGB booster technology enhances color reproduction, delivering vivid and realistic colors that captivate audiences. Additionally, these models feature a contrast ratio of up to 20,000:1, allowing presentations to have deep blacks and bright highlights, critical for effective visual storytelling.

On the other hand, the DW5100UL and PT-DW5100U models are specifically tailored for applications requiring exceptional brightness and excellent color fidelity, boasting a brightness of 5,000 lumens. They offer WXGA resolution (1280 x 800), making them suitable for a wide variety of display needs in corporate, educational, and entertainment settings. The incorporation of Panasonic’s Daylight View technology significantly enhances visibility even in brightly lit environments.

All four projectors are equipped with advanced connectivity options, including HDMI, DisplayPort, and LAN, allowing for easy integration into existing AV systems. They are also compatible with Crestron and AMX control systems, making them a flexible choice for complex installations.

Furthermore, the projectors utilize Panasonic's proprietary Solid Shine laser technology, which ensures consistent brightness and color quality over time while reducing maintenance requirements. With IP6X-rated dust-proof design and a cooling system that minimizes dust accumulation, users can rely on these projectors to perform optimally in challenging conditions.

In summary, Panasonic’s PT-D5700UL, DW5100UL, PT-D5700U, and PT-DW5100U projectors are engineered to deliver outstanding performance, durability, and versatility. They set a high standard for professional projection systems, equipped with cutting-edge technologies that ensure exceptional visual quality whether for business, education, or entertainment purposes.
Top Page Image Contents