Panasonic PT-DW5100U, DW5100UL Cleaning and replacement of air filter, Procedure of cleaning

Page 55

Cleaning and replacement of air filter

If too much dust accumulates on the air filter, [CLEAN THE AIR FILTER]* appears at the lower left of the screen, and the temperature monitor (TEMP) will blink once. If even more dust is allowed to accumulate, the temperature inside the main unit will rise, the temperature monitor (TEMP) will blink twice, and the power is turned off.

Clean the air filter section once every 100 hours or so as a guideline depending on the location of projector operation.

*It appears only for 30 seconds within 3 minutes after the power is turned on. It disappears if any of the buttons on the rear side of the main unit or on the remote control is pressed.

Procedure of cleaning

Turn off the main power and remove the power plug from the receptacle.

Turn off the main power supply observing the procedure (Powering off the projector) on page 25 and then remove the power plug.

Dismantle the air filter.

There are two air filters, one at the left and one at the right.

Use your finger to pull the air filter tab toward you, and remove it from the main unit.

Clean the air filter.

Suck off deposited dust with a vacuum cleaner.

Air filter

Attention • Do not to suck in the air filter itself.

•Do not rinse off the air filter with water. Doing so will impair the filter’s ability to provide protection from dust.

Set the air filter.

Set the air filter in the reverse order to step .

Attention • Fit the air filters into place with the filter material facing the back. (The left and right filters have the same shape.)

•The air filter must be fitted in place when using the projector.

Using the projector without the air filter fitted inside, dirt and dust are sucked into the projector, causing failure.

Note • If cleaning cannot remove the dust completely, then it is a sign to replace the air filter. Consult the dealer. In addition, when the lamp unit is replaced, also replace the air filter.

•Be absolutely sure to use the air filter specifically designed for use with the projector.

55

Page 54 Page 56
Image 55
Page 54 Page 56
Contents Model No. PT-D5700U Commercial UseModel number PT-D5700U/PT-D5700UL/PT-DW5100U/PT-DW5100UL Dear Panasonic CustomerSerial number PT-D5700U/PT-D5700UL/PT-DW5100U/PT-DW5100UL Contents Precautions with regard to safety Always disconnect all cables before moving the projector Remove empty batteries from the remote control at onceDo not use or handle the batteries improperly Do not disassemble the lamp unitElectric shocks can result if this is not done AccessoriesDo not use the old lamp unit Do not place the projector in extremely hot locationsPrecautions on handling Name and function of parts Remote controlBottom Status LED lights Front and side of the projectorRear view of the main unit Controls on rear panel Side-mounted connection terminals Effective range of remote control operation Using the remote control unitLoading dry cells Connect to the projector to use with a cable Setting projector ID number to remote controlInstallation geometry InstallationProjection schemes PT-D5700U, PT-D5700UL Screen aspect ratio Projection distance by projection lensInstallation Screen aspect ratio PT-DW5100U, PT-DW5100ULET-DLE100 ET-DLE200 ET-DLE310 ET-DLE410 PT-DW5100U, PT-DW5100UL Screen aspect ratioCalculation formulas for projection distance by lens types Connection Setup precautionsPin assignments on the RGB2 input terminal are as follows Example of connecting with PCs Example of connecting with AV productsWhen operating at the projector, please refer to Powering up the projectorMaking adjustment and selection Press the I button. on the main unit or the remote controlDirect power off function Powering off the projectorHow to adjust the FOCUS, Zoom and Shift How to adjust the lensHow to remove the projection lens Press the Shutter button again Automatic adjustmentPress the Status button on the remote control Status functionOn-screen menus For RGB signalsFor DVI signals For S-Video/Video/YPBPRsignalsReturning to the previous Menu items settingResetting to the factory default Basic menu operationsAdjusting the picture Adjusting the position Digital Cinema Reality Clock PhaseZoom KeystoneClamp Position Input ResolutionEdge Blending Raster Position XGA ModeSxga Mode Press to select an item, and press to adjust the settingPress to select R, G, B and Wh OPTION1 settingsPress the Enter button Press to adjust the values Color MatchingBack Color Contrast ModeAuto Signal Color CorrectionOSD Position DVI Signal LevelDVI Edid FUNC1Altitude OPTION2 settingsInstallation Projector IDRS-232C Lamp PowerLamp Select Lamp RelayCycle of displayed internal test patterns Auto Power OFFPassword System InformationConnection example Setting the networkConnecting the PC System requirementsClick Change password Using Web Browser ControlAccessing from the Web browser Password changeBasic control Change password buttonDetail control Monitor information Error informationOK Normal operation Failed Occurrence of trouble When Failed has appeared for an item Parameter Description Mail set upAn error is detected by self- diagnosis Mail setup page ContinuingPing test Authentication server set upDNS server set up Change the authentication method as desiredAdjust clock Contents of mail sentNetwork status Network configCommand Control Description Remarks Using the PJLink protocolSupported commands PJLink security authenticationControl Device Setup Setting the securityPassword Change Display SettingExamples of connection Using the serial terminalsPin assignments and signal names Communication conditions Factory settingPin assignments and control Control commandsCable specifications Connecting to a PC Computer Projector DTE specificationsIndication of lamp monitor Dismantle the air filter Cleaning and replacement of air filterProcedure of cleaning Clean the air filterAfter When to replace the Lamp unitReplacing the lamp unit LampHave a Phillips screwdriver ready ahead of time Lamp unit replacement stepsRemove the two screws securing the fan unit Lamp unit will be hot after it has been usedInstallation procedure Ceiling Mount Bracket SafeguardsImage is blurred Power doesNot turn on No imagePT-D5700U PT-D5700UL PT-DW5100U SpecificationsReplacement lamp unit Length of power cord CabinetOutside dimensions Remote control Power sourcePAL-M/PAL60 PAL/PAL-N/SECAM Compatible Signal ListInstallation dimensions diagram DimensionsUnit mm, inch Trademark Acknowledgement Concernant LA Sécurité Ne pas mettre d’objets étrangers dans le projecteur Précautions concernant la sécuritéNe pas surcharger la prise de courant Ne jamais tenter de modifier ou de démonter le projecteurIl y a risque d’électrocution ou d’explosion Pendant un orage, ne pas toucher le projecteur ou le câbleNe jamais démonter la lampe Il y a risque d’électrocutionLe bloc lampe risquerait de se casser Ne pas empêcher la chaleur de s’échapperNe pas utiliser la lampe usée Sinon cela peut causer des chocs électriquesPrécautions pour l’utilisation Nettoyage et maintenancePrécautions pour la manipulation Mise au rebutHeures*2 Remplacement de la lampeMoment adéquat pour remplacer la lampe AprèsPoignée Lampe Procédure de remplacement de la lampeLa lampe est chaude si elle vient d’être utilisée Préparez un tournevis Phillips à l’avancePanasonic Canada Inc Panasonic Projector Systems CompanyTechnical Support Phone FAX Mail projectorsupport@us.panasonic.com

PT-DW5100U, PT-D5700U, DW5100UL, PT-D5700UL specifications

Panasonic, a leader in innovative projection technology, offers a range of high-performance projectors including the PT-D5700UL, DW5100UL, PT-D5700U, and PT-DW5100U. These models are designed for environments that require high brightness, excellent color accuracy, and advanced features for seamless integration into various applications.

The PT-D5700UL and PT-D5700U are renowned for their high brightness of up to 7,000 lumens, making them ideal for large venues such as auditoriums, conference rooms, and outdoor events. They utilize a dual-lamp system, which not only enhances brightness but also provides reliability and longevity. The unique Dual Lamp Drive system ensures that if one lamp fails, the other continues to function, minimizing downtime and maintenance concerns.

Both projectors feature a WUXGA resolution of 1920 x 1200, providing sharp, detailed images that are essential for professional presentations. Their RGB booster technology enhances color reproduction, delivering vivid and realistic colors that captivate audiences. Additionally, these models feature a contrast ratio of up to 20,000:1, allowing presentations to have deep blacks and bright highlights, critical for effective visual storytelling.

On the other hand, the DW5100UL and PT-DW5100U models are specifically tailored for applications requiring exceptional brightness and excellent color fidelity, boasting a brightness of 5,000 lumens. They offer WXGA resolution (1280 x 800), making them suitable for a wide variety of display needs in corporate, educational, and entertainment settings. The incorporation of Panasonic’s Daylight View technology significantly enhances visibility even in brightly lit environments.

All four projectors are equipped with advanced connectivity options, including HDMI, DisplayPort, and LAN, allowing for easy integration into existing AV systems. They are also compatible with Crestron and AMX control systems, making them a flexible choice for complex installations.

Furthermore, the projectors utilize Panasonic's proprietary Solid Shine laser technology, which ensures consistent brightness and color quality over time while reducing maintenance requirements. With IP6X-rated dust-proof design and a cooling system that minimizes dust accumulation, users can rely on these projectors to perform optimally in challenging conditions.

In summary, Panasonic’s PT-D5700UL, DW5100UL, PT-D5700U, and PT-DW5100U projectors are engineered to deliver outstanding performance, durability, and versatility. They set a high standard for professional projection systems, equipped with cutting-edge technologies that ensure exceptional visual quality whether for business, education, or entertainment purposes.
Top Page Image Contents