Panasonic PT-D5700UL, DW5100UL OPTION2 settings, Projector ID, Installation, Altitude, Direction

Page 38

OPTION2 settings

OPTION2

 

 

PROJECTOR ID

ALL

 

INSTALLATION

FRONT-FLOOR

 

ALTITUDE

LOW

 

DIRECTION

HORIZONTAL

 

LAMP SELECT

DUAL

 

LAMP RELAY

OFF

 

LAMP POWER

HIGH

 

RS-232C

 

 

SYSTEM INFORMATION

 

 

AUTO POWER OFF

DISABLE

 

DATE AND TIME

 

 

PASSWORD

 

 

 

 

 

MENU SELECT

 

 

CHANGE

 

PROJECTOR ID

The projector has an ID number setting function that helps the user to control two or more projectors either simultaneously or separately with a single remote control. The ID number is set to “ALL” by default. Hence the ID number need not be set when only one projector is used.

1 – 64 : The ID number is set in this range.

Note • The ID number can be set to “ALL”, or selected from “1” to “64”.

If the projectors are given ID numbers, their remote controls must be assigned the same ID numbers, respectively.

If the ID number of a projector is set to “ALL”, it can be controlled by the remote control or the PC with any ID number.

If multiple projectors are used and some of them have their IDs set to “ALL”, they cannot be controlled separately from the projectors with other ID numbers.

For details on remote control ID setting, see page 15.

INSTALLATION

Switch this setting according to the projector installation method.

FRONT-FLOOR

FRONT-CEILING

REAR-FLOOR

REAR-CEILING

ALTITUDE

The fan can be controlled in accordance with the operating conditions.

LOW : This is the standard setting.

HIGH : This is selected when using the projector at an altitude of over 1 400 m (4 593.2').

DIRECTION

The fan can be controlled in accordance with the direction in which the images are to be projected.

HORIZONTAL: This is the standard setting.

VERTICAL : This is selected when projecting images at a significant angle toward the vertical (more than 30 degrees from the horizontal).

 

 

V

 

H

3 0 °

3 0 °

H

 

3 0 °

3 0 °

 

V

H:HORIZONTAL

V:VERTICAL

Attention • Select the correct “DIRECTION” setting in accordance with the direction in which the images are to be projected.

Using the projector at the wrong

“DIRECTION” setting will shorten the service life of the lamps.

38

Image 38
Contents Commercial Use Model No. PT-D5700USerial number Dear Panasonic CustomerModel number PT-D5700U/PT-D5700UL/PT-DW5100U/PT-DW5100UL PT-D5700U/PT-D5700UL/PT-DW5100U/PT-DW5100UL Contents Precautions with regard to safety Do not disassemble the lamp unit Remove empty batteries from the remote control at onceDo not use or handle the batteries improperly Always disconnect all cables before moving the projectorDo not place the projector in extremely hot locations AccessoriesDo not use the old lamp unit Electric shocks can result if this is not donePrecautions on handling Remote control Name and function of partsBottom Front and side of the projector Status LED lightsRear view of the main unit Controls on rear panel Side-mounted connection terminals Loading dry cells Using the remote control unitEffective range of remote control operation Setting projector ID number to remote control Connect to the projector to use with a cableProjection schemes InstallationInstallation geometry Projection distance by projection lens PT-D5700U, PT-D5700UL Screen aspect ratioInstallation PT-DW5100U, PT-DW5100UL Screen aspect ratioPT-DW5100U, PT-DW5100UL Screen aspect ratio ET-DLE100 ET-DLE200 ET-DLE310 ET-DLE410Calculation formulas for projection distance by lens types Pin assignments on the RGB2 input terminal are as follows Setup precautionsConnection Example of connecting with AV products Example of connecting with PCsPress the I button. on the main unit or the remote control Powering up the projectorMaking adjustment and selection When operating at the projector, please refer toPowering off the projector Direct power off functionHow to remove the projection lens How to adjust the lensHow to adjust the FOCUS, Zoom and Shift Status function Automatic adjustmentPress the Status button on the remote control Press the Shutter button againFor S-Video/Video/YPBPRsignals For RGB signalsFor DVI signals On-screen menusBasic menu operations Menu items settingResetting to the factory default Returning to the previousAdjusting the picture Adjusting the position Keystone Clock PhaseZoom Digital Cinema RealityEdge Blending Input ResolutionClamp Position Press to select an item, and press to adjust the setting XGA ModeSxga Mode Raster PositionColor Matching OPTION1 settingsPress the Enter button Press to adjust the values Press to select R, G, B and WhColor Correction Contrast ModeAuto Signal Back ColorFUNC1 DVI Signal LevelDVI Edid OSD PositionProjector ID OPTION2 settingsInstallation AltitudeLamp Relay Lamp PowerLamp Select RS-232CSystem Information Auto Power OFFPassword Cycle of displayed internal test patternsSystem requirements Setting the networkConnecting the PC Connection examplePassword change Using Web Browser ControlAccessing from the Web browser Click Change passwordDetail control Change password buttonBasic control OK Normal operation Failed Occurrence of trouble Error informationMonitor information Mail set up When Failed has appeared for an item Parameter DescriptionMail setup page Continuing An error is detected by self- diagnosisChange the authentication method as desired Authentication server set upDNS server set up Ping testContents of mail sent Adjust clockNetwork config Network statusPJLink security authentication Using the PJLink protocolSupported commands Command Control Description RemarksDisplay Setting Setting the securityPassword Change Control Device SetupCommunication conditions Factory setting Using the serial terminalsPin assignments and signal names Examples of connectionConnecting to a PC Computer Projector DTE specifications Control commandsCable specifications Pin assignments and controlIndication of lamp monitor Clean the air filter Cleaning and replacement of air filterProcedure of cleaning Dismantle the air filterLamp When to replace the Lamp unitReplacing the lamp unit AfterLamp unit will be hot after it has been used Lamp unit replacement stepsRemove the two screws securing the fan unit Have a Phillips screwdriver ready ahead of timeCeiling Mount Bracket Safeguards Installation procedureNo image Power doesNot turn on Image is blurredSpecifications PT-D5700U PT-D5700UL PT-DW5100URemote control Power source Length of power cord CabinetOutside dimensions Replacement lamp unitCompatible Signal List PAL-M/PAL60 PAL/PAL-N/SECAMUnit mm, inch DimensionsInstallation dimensions diagram Trademark Acknowledgement Concernant LA Sécurité Ne jamais tenter de modifier ou de démonter le projecteur Précautions concernant la sécuritéNe pas surcharger la prise de courant Ne pas mettre d’objets étrangers dans le projecteurIl y a risque d’électrocution Pendant un orage, ne pas toucher le projecteur ou le câbleNe jamais démonter la lampe Il y a risque d’électrocution ou d’explosionSinon cela peut causer des chocs électriques Ne pas empêcher la chaleur de s’échapperNe pas utiliser la lampe usée Le bloc lampe risquerait de se casserMise au rebut Nettoyage et maintenancePrécautions pour la manipulation Précautions pour l’utilisationAprès Remplacement de la lampeMoment adéquat pour remplacer la lampe Heures*2Préparez un tournevis Phillips à l’avance Procédure de remplacement de la lampeLa lampe est chaude si elle vient d’être utilisée Poignée LampePhone FAX Mail projectorsupport@us.panasonic.com Panasonic Projector Systems CompanyTechnical Support Panasonic Canada Inc

PT-DW5100U, PT-D5700U, DW5100UL, PT-D5700UL specifications

Panasonic, a leader in innovative projection technology, offers a range of high-performance projectors including the PT-D5700UL, DW5100UL, PT-D5700U, and PT-DW5100U. These models are designed for environments that require high brightness, excellent color accuracy, and advanced features for seamless integration into various applications.

The PT-D5700UL and PT-D5700U are renowned for their high brightness of up to 7,000 lumens, making them ideal for large venues such as auditoriums, conference rooms, and outdoor events. They utilize a dual-lamp system, which not only enhances brightness but also provides reliability and longevity. The unique Dual Lamp Drive system ensures that if one lamp fails, the other continues to function, minimizing downtime and maintenance concerns.

Both projectors feature a WUXGA resolution of 1920 x 1200, providing sharp, detailed images that are essential for professional presentations. Their RGB booster technology enhances color reproduction, delivering vivid and realistic colors that captivate audiences. Additionally, these models feature a contrast ratio of up to 20,000:1, allowing presentations to have deep blacks and bright highlights, critical for effective visual storytelling.

On the other hand, the DW5100UL and PT-DW5100U models are specifically tailored for applications requiring exceptional brightness and excellent color fidelity, boasting a brightness of 5,000 lumens. They offer WXGA resolution (1280 x 800), making them suitable for a wide variety of display needs in corporate, educational, and entertainment settings. The incorporation of Panasonic’s Daylight View technology significantly enhances visibility even in brightly lit environments.

All four projectors are equipped with advanced connectivity options, including HDMI, DisplayPort, and LAN, allowing for easy integration into existing AV systems. They are also compatible with Crestron and AMX control systems, making them a flexible choice for complex installations.

Furthermore, the projectors utilize Panasonic's proprietary Solid Shine laser technology, which ensures consistent brightness and color quality over time while reducing maintenance requirements. With IP6X-rated dust-proof design and a cooling system that minimizes dust accumulation, users can rely on these projectors to perform optimally in challenging conditions.

In summary, Panasonic’s PT-D5700UL, DW5100UL, PT-D5700U, and PT-DW5100U projectors are engineered to deliver outstanding performance, durability, and versatility. They set a high standard for professional projection systems, equipped with cutting-edge technologies that ensure exceptional visual quality whether for business, education, or entertainment purposes.