Panasonic DW5100UL, PT-D5700UL Powering off the projector, Direct power off function

Page 25

Powering off the projector

Press the POWER STANDBY “ ” button.

Select “OK” with or button and press the ENTER button.

(Or press the POWER STANDBY “ ” button again.)

The projection of the image stops, and the power indicator of the main unit lights up orange. (The cooling fan keeps running.)

Wait until the power indicator of the main unit turns to red (i.e., until the cooling fan stops).

Press the “ ” marked side of the MAIN POWER switch to remove all power from the projector.

Attention • Do not turn the power supply off and then immediately back on again.

Turning on the power supply may not light up the light source lamp if the lamp is in the process of cooling down after turning off the power supply. To light up the lamp, turn on the power supply again when the lamp has been cooled sufficiently. Turning on the power supply with the lamp in the hot condition may shorten the lamp life.

Note • The projector consumes approximately 10 watts of power even in standby mode after the cooling fan stops. (Power indicator lit in red.)

•If you re-power the projector after shutting off the main power inadvertently, the projection lamp may remain unlit. Please turn the main power on again after a while.

Direct power off function

The power supplied internally causes the cooling fan to continue operating and cool off in the event that the power has failed or even after the power cord is accidentally disconnected immediately after the power has been turned off.

Note • When the lamp has been cooled by the direct power off function, it sometimes

takes longer than usual for the lamp to light up again.

•While the cooling fan is operating, do not place the projector inside a box or bag.

25

Page 24 Page 26
Image 25
Page 24 Page 26
Contents Model No. PT-D5700U Commercial UseModel number PT-D5700U/PT-D5700UL/PT-DW5100U/PT-DW5100UL Dear Panasonic CustomerSerial number PT-D5700U/PT-D5700UL/PT-DW5100U/PT-DW5100UL Contents Precautions with regard to safety Do not use or handle the batteries improperly Remove empty batteries from the remote control at onceDo not disassemble the lamp unit Always disconnect all cables before moving the projectorDo not use the old lamp unit AccessoriesDo not place the projector in extremely hot locations Electric shocks can result if this is not donePrecautions on handling Name and function of parts Remote controlBottom Status LED lights Front and side of the projectorRear view of the main unit Controls on rear panel Side-mounted connection terminals Effective range of remote control operation Using the remote control unitLoading dry cells Connect to the projector to use with a cable Setting projector ID number to remote controlInstallation geometry InstallationProjection schemes PT-D5700U, PT-D5700UL Screen aspect ratio Projection distance by projection lensInstallation Screen aspect ratio PT-DW5100U, PT-DW5100ULET-DLE100 ET-DLE200 ET-DLE310 ET-DLE410 PT-DW5100U, PT-DW5100UL Screen aspect ratioCalculation formulas for projection distance by lens types Connection Setup precautionsPin assignments on the RGB2 input terminal are as follows Example of connecting with PCs Example of connecting with AV productsMaking adjustment and selection Powering up the projectorPress the I button. on the main unit or the remote control When operating at the projector, please refer toDirect power off function Powering off the projectorHow to adjust the FOCUS, Zoom and Shift How to adjust the lensHow to remove the projection lens Press the Status button on the remote control Automatic adjustmentStatus function Press the Shutter button againFor DVI signals For RGB signalsFor S-Video/Video/YPBPRsignals On-screen menusResetting to the factory default Menu items settingBasic menu operations Returning to the previousAdjusting the picture Adjusting the position Zoom Clock PhaseKeystone Digital Cinema RealityClamp Position Input ResolutionEdge Blending Sxga Mode XGA ModePress to select an item, and press to adjust the setting Raster PositionPress the Enter button Press to adjust the values OPTION1 settingsColor Matching Press to select R, G, B and WhAuto Signal Contrast ModeColor Correction Back ColorDVI Edid DVI Signal LevelFUNC1 OSD PositionInstallation OPTION2 settingsProjector ID AltitudeLamp Select Lamp PowerLamp Relay RS-232CPassword Auto Power OFFSystem Information Cycle of displayed internal test patternsConnecting the PC Setting the networkSystem requirements Connection exampleAccessing from the Web browser Using Web Browser ControlPassword change Click Change passwordBasic control Change password buttonDetail control Monitor information Error informationOK Normal operation Failed Occurrence of trouble When Failed has appeared for an item Parameter Description Mail set upAn error is detected by self- diagnosis Mail setup page ContinuingDNS server set up Authentication server set upChange the authentication method as desired Ping testAdjust clock Contents of mail sentNetwork status Network configSupported commands Using the PJLink protocolPJLink security authentication Command Control Description RemarksPassword Change Setting the securityDisplay Setting Control Device SetupPin assignments and signal names Using the serial terminalsCommunication conditions Factory setting Examples of connectionCable specifications Control commandsConnecting to a PC Computer Projector DTE specifications Pin assignments and controlIndication of lamp monitor Procedure of cleaning Cleaning and replacement of air filterClean the air filter Dismantle the air filterReplacing the lamp unit When to replace the Lamp unitLamp AfterRemove the two screws securing the fan unit Lamp unit replacement stepsLamp unit will be hot after it has been used Have a Phillips screwdriver ready ahead of timeInstallation procedure Ceiling Mount Bracket SafeguardsNot turn on Power doesNo image Image is blurredPT-D5700U PT-D5700UL PT-DW5100U SpecificationsOutside dimensions Length of power cord CabinetRemote control Power source Replacement lamp unitPAL-M/PAL60 PAL/PAL-N/SECAM Compatible Signal ListInstallation dimensions diagram DimensionsUnit mm, inch Trademark Acknowledgement Concernant LA Sécurité Ne pas surcharger la prise de courant Précautions concernant la sécuritéNe jamais tenter de modifier ou de démonter le projecteur Ne pas mettre d’objets étrangers dans le projecteurNe jamais démonter la lampe Pendant un orage, ne pas toucher le projecteur ou le câbleIl y a risque d’électrocution Il y a risque d’électrocution ou d’explosionNe pas utiliser la lampe usée Ne pas empêcher la chaleur de s’échapperSinon cela peut causer des chocs électriques Le bloc lampe risquerait de se casserPrécautions pour la manipulation Nettoyage et maintenanceMise au rebut Précautions pour l’utilisationMoment adéquat pour remplacer la lampe Remplacement de la lampeAprès Heures*2La lampe est chaude si elle vient d’être utilisée Procédure de remplacement de la lampePréparez un tournevis Phillips à l’avance Poignée LampeTechnical Support Panasonic Projector Systems CompanyPhone FAX Mail projectorsupport@us.panasonic.com Panasonic Canada Inc

PT-DW5100U, PT-D5700U, DW5100UL, PT-D5700UL specifications

Panasonic, a leader in innovative projection technology, offers a range of high-performance projectors including the PT-D5700UL, DW5100UL, PT-D5700U, and PT-DW5100U. These models are designed for environments that require high brightness, excellent color accuracy, and advanced features for seamless integration into various applications.

The PT-D5700UL and PT-D5700U are renowned for their high brightness of up to 7,000 lumens, making them ideal for large venues such as auditoriums, conference rooms, and outdoor events. They utilize a dual-lamp system, which not only enhances brightness but also provides reliability and longevity. The unique Dual Lamp Drive system ensures that if one lamp fails, the other continues to function, minimizing downtime and maintenance concerns.

Both projectors feature a WUXGA resolution of 1920 x 1200, providing sharp, detailed images that are essential for professional presentations. Their RGB booster technology enhances color reproduction, delivering vivid and realistic colors that captivate audiences. Additionally, these models feature a contrast ratio of up to 20,000:1, allowing presentations to have deep blacks and bright highlights, critical for effective visual storytelling.

On the other hand, the DW5100UL and PT-DW5100U models are specifically tailored for applications requiring exceptional brightness and excellent color fidelity, boasting a brightness of 5,000 lumens. They offer WXGA resolution (1280 x 800), making them suitable for a wide variety of display needs in corporate, educational, and entertainment settings. The incorporation of Panasonic’s Daylight View technology significantly enhances visibility even in brightly lit environments.

All four projectors are equipped with advanced connectivity options, including HDMI, DisplayPort, and LAN, allowing for easy integration into existing AV systems. They are also compatible with Crestron and AMX control systems, making them a flexible choice for complex installations.

Furthermore, the projectors utilize Panasonic's proprietary Solid Shine laser technology, which ensures consistent brightness and color quality over time while reducing maintenance requirements. With IP6X-rated dust-proof design and a cooling system that minimizes dust accumulation, users can rely on these projectors to perform optimally in challenging conditions.

In summary, Panasonic’s PT-D5700UL, DW5100UL, PT-D5700U, and PT-DW5100U projectors are engineered to deliver outstanding performance, durability, and versatility. They set a high standard for professional projection systems, equipped with cutting-edge technologies that ensure exceptional visual quality whether for business, education, or entertainment purposes.
Top Page Image Contents